Table of Contents
Advertisement
....
:/i
"<
i ¸
MODEL NO.
]]3.20680
JOINTER/PLANER
ONLY
113.206930
JOINTER!PLANER
WITH
LEGS AND MOTOR
Serial
Number .......................................
Model and serial
number may be found
on a plate attached
to your infeed table.
You should record both
model and serial number
in a safe place for
future use.
CAUTION:
Read
GENERAL
and
ADDiTiONAL
SAFETY
iNSTRUCTiONS
carefully
k •::
'_,/,_
__
_ i_: _i, _ ,///i
...... • ',
CRn MaNo
6_- INCH JOIN TER- PLANER
® assembly
® operating
o repair
parts
Sotd by SEARS,
ROEBUCK.
AND
CO.,
Chicago,
_t. 60684
U.S.A.
PartNo.67036
:.......... ' : : :: ':
Advertisement
Table of Contents
Related Manuals for Sears Craftsman 113.20680
Summary of Contents for Sears Craftsman 113.20680
- Page 1 CAUTION: Read GENERAL ADDiTiONAL SAFETY iNSTRUCTiONS carefully Sotd by SEARS, ROEBUCK. PartNo.67036 k •:: '_,/,_ _ i_: _i, _ ,///i ... • ', CRn MaNo 6_- INCH JOIN TER- PLANER ® assembly ®...
-
Page 2: Power Tools
FULL ONE YEAR WARRANTY year from the date of purchase, this Craftsman Jointer/Planer fails due to a defect in material rs will repair it, free of charge. THROUGHOUT SEARS, general safety 1.:KNOW YOUR POWER TOOL Read owner's manual carefully. application... -
Page 3: Operation
Safety is a combination Of operator alertness at all times when the Jointer-Planer is being used. WARNING: FOR YOUR OWN SAFETY, TEMPT TO OPERATE YOUR JOINTER-PLANER IS COMPLETELY ASSEMBLED ACCORDING TO THE INSTRUCTIONS, YOU HAVE READ AND UNDERSTOOD ING, 1. GENERAL... -
Page 4: Safety Instructions
{4) feet :long, make. sure it is supported 15. Never leave the Jointer-Planer work area with the power on, before the 3ointer-Ptaner has come to a complete stop; or without removing and storing the switch key. -
Page 5: Connecting To Power Source Outlet
• motor spec faCahons and e ectrmcalrequmrements Th_is machine is designed to use a 3450 use any motor that r._r_s faster' It is wired operation on t10-t20 nating current. MUST OPERATE VOI.TS. EVEN THOUGH RECOMMENDED MOTORS THESE CRAFTSMAN MOTORS FOUND TO BE ACCEPTABLE THIS TOOL. - Page 6 : :::i: : ::_ : _ Model t13.20680 JointeriPlaner iS shipped 'one. cartOn, DOES INCLUDE motori Model t13.206930 Jointer/Planer is shipped one carton INCLUDES Steel Legs, and Motor. Separate all: parts from packing materials one with the illustration and the list of Loose...
-
Page 7: Table Of Contents
unpacking Qnd checking TABLE OF LOOSE PARTS The Following Parts Are Included With Model 113.206930 Only Item Description End Stiffener Side Stiffener Motor Support Motor Package of Miscellaneous Small Parts, No. 67035, Consisting of the Following: Cord Clip Hex Nut, 1/4 in. -
Page 8: F Cord Clip
(touches) tighten not, follow tightening screws BLADES" slip off the wrench." HEAD SCREW ____ JO INTER/PLANER STIFFENER 1-1/4 IN. SCREW DEPTH OF CUT HANDWHEEL 5/32 IN. SETSCREW WRENCH WEDGE CUTTER GUARD blade adjustment is not required, check each of each wedge (5/32"... -
Page 9: G Hex Nut, 1/4 In
AND BELT GUARDS See page 5 for recommended motors. PARTS NEEDED 4 carriage bolts, 5]16-18 in., washers and nuts. 1 Jointer Planer Belt Guard Motor Pulley Belt Guard Belt Guard Support Belt Guard Support Bracket 1, Place motor on your workbench with... -
Page 10: 2In
¸ C_i _:!:iin:motoK pdiley and:place:Pulley:iOn f|U_h:! _itt+ end i: motor rn_:$ _iewed from +PULLEY end: 1_ Place m0tor on your workbench or on floor. 2. Stand clear of motor and plug cord into a properly grounded outlet (See page 5). Notice rotation of pulley, If it is:not= turning COUNTERCLOCKWISE, plug from outlet, and change rotation of motor accord- ing to instructiOns furnished with motor;... - Page 11 8. Snap guard into position as shown. Remove knob and washer.., lift guard up. Loosen the two MOTOR BASE CLAMP rotate the motor so that the ventilation downward, tighten base clamp screws. Install 2_t/2 "' pulley motor motor sideways until the motor pulley the pulley...
-
Page 12: Fence Locks And Stops
i ¸ know SLIDE BRACKET 11: DEPTH OF CUT HANDWHEEL. handwheel counterclockwise table to maximum depth of 1/8 in, _.. FENCE LOCKS AND STOPS. moved across the Jointer to take full advantage of the "sharpness" of the blades. The:fence should be positioned to the extreme right (toward pulley) but not beyond the end of the blades. -
Page 13: Fence Tilt Scale
b. Before tightening fence lock down outfeed table c. 90 ° Fence Stop positions fence To tilt fence, loosen sto;p out. Tilt to desired angle and tighten knobs. d. To fence at 90 ° to tables, knobs, tilt fence so t;qe stop place. - Page 14 tO know ::e. Adjust stop the same NOTE: Tilt scale will not require was= adjusted foi _ 90 ° position. CUTTER GUARD. Provides cutter head. It must always be in place and function- ing properly. Check the. guard to make sure it iS functioning perly.
- Page 15 Insert a pencit in space at end of cutterhead hold cutterguard open. Place a straightedge (large square or tong level) on outfeed table. First along one side than other. c. Raise infeed table until it touches Sight between table and straightedge high condition It is easier to adjust...
-
Page 16: On-Off Switch
IS INTENDED UNAUTHORIZED HAZARDOUS CHILDREN OTH ERS. a, Insert Key into switch. NOTE: Key is made of yellow plastic. your io nter planer LEVELING STUDS VIEW LOOKING UP FOR PARTS IDENTIFICATION studs until TIGHTEN screws are:::itight; that it wiff be... - Page 17 b, To turn machine insert finger lever and pull end of switch out. c, To turn machine OFF... PUSH lever in, Never leave machine unattended until to a complete stop. d. To lock switch in OFF position,,, with one hand... REMOVE key with WARNING:...
-
Page 18: Feeding The Workpiece
_i -_ • • - ,., For your own safetY:, ALWAYS bi0cks.when JOiN_lNGw0od 3in.. !:.o_ whenP LANt NG:w00d: that is THIN NE R than 3 in: Do not plane, joint 0r bevel wood Material this short is more difficult FEEDING THE WORKPIECE Hold board... - Page 19 :_ _:_ i_ _ : ,i Always feed WITH THE GRAIN whenever possible. If the nature of the workpiece is such that it must be fed AGAli_ST THE GRAIN, take very light cuts and feed slowly. USING THE HOLD DOWN/PUSH ALWAYS use the hold down/push...
- Page 20 when pianing wood 3/4 in, thick and NARROWER holdldownipush b!ock_ tilt block so that it clea_s"the top of the cutterguard #eeding. Never plane wood that is thinner than 1/2 in... it }s apt. to split or:Shatter and thus has a greater tenden- cy to kickback, BEVELING Adjust...
- Page 21 SWITCH "OFF"AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE ADJUSTING, MAINTAIN- ING, OR LUBRICATING YOUR JOINTER-PLANER. Remove belt guard. 2. Position fence to right . . . approximately beyond cutter blades , , . lock it in pDace. 3. Lower infeed table all the way down.
-
Page 22: Maintenance
.003 average piece Of paper). NOTE: Sears has a knife setting gauge for this purpose. Cat. # 9-2647 13. "Now install both locking setscrews and tighten (with the 5/32" setscrew wrench) alternately a little at a time. - Page 23 INSTALLING CUTTER GUARD SPRING 1. Remove cotter pin from pivot pin in cutter remove guard (located underneath Spring must appear as in sketch from feed table, will perform properly upside down. 1. Position guard as shown, with PIVOT in infeed table.
- Page 24 No. 20 or No. 30 engine 0il to pivot pin. 5. Replace guard and cotter p_n. If guard still does not return to its REST sult your local Sears Retail Store before jointer-planer, SHARPENING: CUTTER BLADES blades can be honed individually...
-
Page 25: Wiring Diagram
Keep your jointer-planer clean. Put a carton of a container underneath your iointer-ptaner chips. The container should reach above the motor. allow pitch accumulate on the tables, fence, cutter guard, the cutter head Clean them with Craftsman and Pitch... -
Page 26: Troubleshooting
CHART PROBABLE CAUSE, 1. RePlace defective parts before using machine again. 2. Consult Sears Service. Any attempt to repair this motor may create a HAZARD unlessrepair is done by a qualified service technician. Repair service is available at your nearest Sears Store. - Page 27 HARDWARE FIGURE 1 oSupptied *Standard FIGURE LEGS PARTS LIST Part Description 67033 Stiffener, 60314 o *Screw, Truss Hd. 1/4 - 20 × 5/8 STD55t225 o *Lockwasher, 1/4 External STD541025 • *Nut, Hex 1/4 - 20 67032 Stiffener, Side 62614 62204 m Clip, Cord 67034 Support,...
- Page 28 CRAFTSMAN --49 FIGURE 2 6-1!8 tNCH JOINTER-PLANER MODEL _r_SWITCH BOX ASSEMBLY SEE FIGURE 5 FOR . ./" EXPLODED VIEW No, 113.20680 AND 113,206930 SEE FIGURE 4 FOR EXPLODED VIEW ..._3...
- Page 29 Hex., 5/32 455872 Screw Mach., wiLockwasher 63410 Knob, 3_!/4 67016 Shaft, Elevating MODEL No. 113.20680 AND 113.206930 FIGURE 2 PARTS LIST Description Complete (See Fig. 3) Guard Retaining Set Screw, 2" Dia. x 1/2 '; 5/8" Bore, Keyed x 5/16, Soc Hd.
-
Page 30: 1/4-20
STD522505 "Screw, C_p, 1_/4-20 STD551025 11 : *Wastler, Pt.ai:rto 1 7/.64 : 121812 Plate, Tension *Standard Hardware items-- 3OtINTER-PLANER MODEL No. 113.20680 FIGURE 3 INFEED TABLE PARTS LIST 21422 21219 21218 P_ate) STD 551131 x 7/8 21635 STD523112 STD551031 21204 112, He×. -
Page 31: Parts List
No. 8-32 x 1/4, Bind Hd., Slotted 102817 Screw, Set, 1/4-20 Pt. Slotted FIGURE F]JGURE SEE WIRING DIAGRAM ON PAGE 25 MODEL No. 113.20680 FENCE ASSEMBLY PARTS LiST , ,,,,, ... _ Part 21229 STD551210 STD5 ! t 102 x 1-1/4, 67009... -
Page 32: Repair Parts
MODEL NUMBER 113.20680 113.206930 All parts listed may be ordered from any Sears Service Center and most Sears stores, tf the parts you need are not stocked Iocaity, your order wifl be electronically Repair Parts Distribution ROEBUCK CO., Form No. SP4401 ...::<...
Need help?
Do you have a question about the Craftsman 113.20680 and is the answer not in the manual?
Questions and answers