Table of Contents
Advertisement
FENCE
1..
From among
the loose parts find the following:
(1) Fence
(2) Fence
Brackets
(2) Fence Segments
(2) Tilt Indicators
(2) Lock Knobs
(4) 114-20 x 3t4" Hex Cap Screws
(4) 1t4 Lock Washei's
(4) 9132 ID x 91t60D
x 11t6 Thick Washers
NOTE:USE
OF
WASHER_
LEES
THAN
1/_
THICK
LOCK KNO_
MAY
RE/;DLT
|t_
FENCE
Tt(]HTEN_ND
PROBLEM_;
_132
_DX
_Tt3_OD
(2) 9f32 ID x 17132 OD x 1/8 Thick Washers
._
j_L._,jA.2_
(6) #8-32 x !12 Flat Head Machine
Screws
FE
',o (6) #8 Fiat Washers
EASE.
HCESnAC_
,,A_2_AX_H_X w
(2) #10-24 X 112 Pan Head Machine
Screws
\,._
(2)#10
FEat Washers
1
___'_1%_";
°°c"wAsH" __
......
9132 ID x 1/16 thick
washers
and 114 lock washers, snug but do not
tighten
#t0.z4x _/2 PAN ,_0
2.
Attach
fence segments
to fence with #8-32 flat head screws,
#8 flat
_"_
I
_CH=NE SCREW
washers
and #8-32 hex nuts.
3
PIEce assembled
fence
on machine
with
fence brackets
inside the
fence segments
4
Position
lock knobs with 9/32 tD x t7/32 OD x 118 thick
washers
thru
slots
in fence segments
and thread
into fence brackets
5
Place
squa_'e against
face of fence and table surface
Bring fence
square
to table and tighten
lock knobs.
6
THERE MUST BE 1/32" TO 1t16" gap between
the lower edge of the
fence and jointer
tables (with table set for 0" cut). To adjust,
move
fence assembly
by loosening the 1t4-20 x 314 hex cap screws attach-
ing the fence
brackets
to the base
Retighten
hex cap screws
after
adjustment
has been made
7
8
9,,
Recheck
squareness
of
fence,,
_
/
TILT
INDICATOR
SHOULD
DE LINED
UP WITH
r_
t_ll
LU_=_,.--"_,_.}_'_,_
THE
FENCE
SEGMENT
AT
THE O'MARK
Install
tilt indicators
with #t0-24 x 112 pan head machine
screw
and
_- _._
_*'J_l,_
DO NOT OVER
#10 flat washers_ Set 0 ° of indicators
to 0 ° of segments
and tighten
"_-_..
_-_.._
TIGHTEN
the screw
The fence should now be adjusted
and wilt accurately
measure
angles
2r"
.'="_/"
-"
_'___
'"-
FENCE
EXTENSION
To aid in edge jointtng
of workpteces
4" and wider, you may extend
the
fence height.
The extension
can be constructed
of 1" (314" thick) stock
pine or hardwood..
Use #8 flat head wood screws of sufficient
length
to securely
attach
the
extension
to the fence
Make sure that the head of the screws
are below
the surface
of the fence
so a s not to interfere with the workpiece
For extra
stability,
additional
countersunk
holes
may be drilled
in the
fence for flat head screws.
w
C
1/4
#,8 FLATHEAD
-
'
COUNT_
SCREW_
FENCE-t
Hide quick links:
Advertisement
Table of Contents
