Care & Cleaning (Cleaning Chart) ......25 Before Setting Surface Controls ......7 Care & Cleaning ..........26 Setting Surface Controls ........9 Before You Call ..........29 Before Setting Oven Controls ....... 12 Major Appliance Warranty ........32 www.frigidaire.com USA 1-800-944-9044 www.frigidaire.ca Canada 1-800-265-8352...
WELCOME & CONGRATULATIONS Congratulations on your purchase of a new appliance! At Product Registration Electrolux Home Products, we are very proud of our Register Your Product product and are completely committed to providing you with the best service possible. Your satisfaction is our The PRODUCT number one priority.
IMPORTANT SAFETY INSTRUCTIONS Read all instructions before using this appliance. • Remove all tape and packaging wrap before using Save these instructions for future reference. the appliance. Destroy the carton and plastic bags after unpacking the appliance. Never allow DEFINITIONS children to play with packaging material.
Page 4
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT CAUTION Do not attempt to operate the appliance during a Do not store items of interest to children in the power failure. If the power fails, always turn off cabinets above the appliance. Children climbing on the unit.
Page 5
IMPORTANT SAFETY INSTRUCTIONS due to the sudden change in temperature. Check the • Do not use a broiler pan without its insert. Broiler manufacturer’s recommendations for cooktop use. pan and grid allow dripping fat to drain and be kept away from the high heat of the broiler. •...
FEATURES AT A GLANCE YOUR BUILT-IN RANGE FEATURES: Electronic oven control with kitchen timer. Left front element control and electronic display. Left rear element control and electronic display. Right rear element control and electronic display. Right front element control and electronic display. Keep warm zone control.
BEFORE SETTING SURFACE CONTROLS COOKTOP DISPLAY WINDOWS POWER FAILURE (PF) MESSAGE The cooktop controls provide a digital display for each The PF message (Figure 9) will be displayed whenever element located on the cooktop. Power levels and there has been a power interruption to the appliance. messages are easily monitored and adjusted using the The PF message will disappear by itself after a few corresponding control keypads in combination with the...
BEFORE SETTING SURFACE CONTROLS USING PROPER COOKWARE ABOUT THE RADIANT SURFACE ELEMENTS The size and type of cookware used will infl uence the The element temperature rises gradually and evenly. setting needed for best cooking results. Be sure to follow As the temperature rises, the element will glow red.
SETTING SURFACE CONTROLS SINGLE RADIANT ELEMENT To Operate the Single Radiant Surface Elements: 1. Place correctly sized cookware on the radiant surface The cooktop provides single element. radiant element located as illustrated. Use the following 2. Touch and hold the instructions when operating for the desired element position these elements.
SETTING SURFACE CONTROLS DUAL RADIANT ELEMENT The cooktop provides a dual radiant element located as illustrated. Use the following instructions when operating this element. Use the Size keypad (Fig. 1) to select which portions of the dual element are needed for heating. The dual element size may be changed anytime the element is ON.
SETTING SURFACE CONTROLS KEEP WARM ZONE CAUTION The cooktop provides a keep warm zone located as illustrated. The keep warm zone will not glow red when it is hot, Use the following instructions but becomes hot enough to cause burns. Avoid placing when operating this element.
BEFORE SETTING OVEN CONTROLS ARRANGING OVEN RACKS Oven vents location ALWAYS ARRANGE OVEN RACKS WHEN THE OVEN IS The upper and lower ovens COOL (PRIOR TO OPERATING THE OVEN). Always use are vented at the back of oven mitts when using the oven. the cooktop.
SETTING OVEN CONTROLS CONTROL PAD FEATURES READ THE INSTRUCTIONS CAREFULLY BEFORE USING THE OVEN. For satisfactory use of your oven, become familiar with the various features and functions of the oven as described below. Detailed instructions for each feature and function follow later in this Use & Care Guide. 1.
SETTING OVEN CONTROLS MINIMUM AND MAXIMUM CONTROL PAD SETTINGS All of the features listed below have minimum and maximum time or temperature settings that may be entered into the control. An ENTRY acceptance beep will sound each time a control pad is touched (the acceptance beep on the Oven Lockout pad is delayed 3 seconds).
Page 15
SETTING OVEN CONTROLS SETTING THE CLOCK SETTING CONTINUOUS BAKE OR 6 HOUR ENERGY SAVING The SET CLOCK pad is used to set the clock. The clock may be set for 12 or 24 hour time of day operation. The TIMER and SELF CLEAN pads control the The clock has been preset at the factory for the 12 hour Continuous Bake or 6 Hour Energy Saving features.
SETTING OVEN CONTROLS SETTING LOCKOUT FEATURE 2. Press SELF CLEAN to switch between normal sound operation and silent operation mode. The display will show either "bEEP On" or "bEEP OFF". pad controls the Lockout feature. The Lockout feature automatically locks the oven doors, the control Note: If "bEEP On"...
SETTING OVEN CONTROLS QUICK PREHEAT SETTING BAKE Use the quick preheat feature when using single rack The BAKE pad controls normal baking. If a rapid baking to quickly heat the oven to bake temperatures. preheating is preferred, refer to the QUICK PREHEAT Use this feature only for standard baking.
SETTING OVEN CONTROLS SETTING BAKE TIME SETTING DELAY START Bake Time allows the oven to be set to cook for a specifi c The BAKE, BAKE TIME and DELAY START pads control length of time and shut off automatically. the Delayed Time Bake feature. The automatic timer of the The oven will shut off and will beep when the countdown Delayed Time Bake will turn the oven on and off at the is fi...
SETTING OVEN CONTROLS SETTING BROIL To set a Broil of 500°F: 1. Place the broiler pan insert on the broiler pan. Then place This mode is best for meats, fi sh and poultry up to 1” the food on the broiler pan insert. DO NOT use the broiler thick.
SETTING OVEN CONTROLS SETTING PIZZA SETTING KEEP WARM The PIZZA pad has been designed to give optimum This mode is best for keeping oven baked foods warm cooking performance when cooking your favorite pizza. for serving after cooking has fi nished. The KEEP WARM The Pizza pad let you choose a preset between a frozen pad turns ON the Keep Warm feature and will maintain pizza (425°F) and a fresh pizza (400°F).
Page 21
SETTING OVEN CONTROLS SETTING THE SABBATH FEATURE (for use on NOTE the Jewish Sabbath & Holidays) The BAKE TIME and DELAY START pads are used to You may change the oven temperature once baking has set the Sabbath feature. The Sabbath feature may only be started by pressing BAKE, the numeric key pads for the used with the BAKE pad.
SETTING OVEN CONTROLS ADJUSTING OVEN TEMPERATURE OVEN LIGHT The temperature in the oven has been pre-set at the Each oven is equipped with an oven light. The oven light factory. When fi rst using the oven, be sure to follow will turn on automatically, when the oven door is opened.
SELF-CLEANING SELF-CLEANING What to Expect during Cleaning A self-cleaning oven cleans itself with high temperatures While the oven is in operation, the oven heats to (well above normal cooking temperatures) which temperatures much higher than those used in normal eliminate soils completely or reduces them to a fi ne cooking.
Page 24
SELF-CLEANING SETTING SELF-CLEAN CYCLE TIME LENGTH The SELF CLEAN and DELAY START pads controls the Delayed Self-Clean operation. The automatic timer will turn The SELF CLEAN pad controls the Self-Cleaning feature. the oven on and off at the time you select in advance. If you are planning to use the oven directly after a self- clean cycle remember to allow time for the oven to cool To set the control for the Self-Cleaning Cycle to...
CARE & CLEANING (Cleaning Chart) CLEANING VARIOUS PARTS OF YOUR APPLIANCE Before cleaning any part of the appliance, be sure all controls are turned off and the appliance is COOL. REMOVE SPILLOVERS AND HEAVY SOILING AS SOON AS POSSIBLE. REGULAR CLEANING WILL REDUCE THE NUMBER OF MAJOR CLEANING LATER.
CARE & CLEANING CERAMIC GLASS COOKTOP CLEANING & CLEANING RECOMMENDATIONS FOR THE MAINTENANCE CERAMIC GLASS COOKTOP Consistent and proper cleaning is essential to CAUTION maintaining your Ceramic glass cooktop. Before cleaning the cooktop, be sure the controls are Prior to using your cooktop for the turned to OFF and the cooktop is COOL.
CARE & CLEANING CLEANING RECOMMENDATIONS FOR THE CARE AND CLEANING OF STAINLESS STEEL Some models are equipped with stainless steel exterior CERAMIC GLASS COOKTOP (CONTINUED) parts. Special care and cleaning are required for Plastic or foods with a high sugar content: maintaining the appearance of stainless parts.
Page 28
CARE & CLEANING REMOVING AND REPLACING THE LIFT- 3. Firmly grasp both sides of oven door along the door sides (Do not use the oven door handle - See Figure 3). OFF OVEN DOOR CAUTION The door is heavy. For safe, temporary storage, lay the door fl...
BEFORE YOU CALL (Solutions to Common Problems) OVEN BAKING For best cooking results, heat the oven before baking cookies, breads, cakes, pies or pastries, etc. There is no need to preheat the oven for roasting meat or baking casseroles. The cooking times and temperatures needed to bake a product may vary slightly from your previously owned appliance.
Page 30
BEFORE YOU CALL (Solutions to Common Problems) IMPORTANT Before you call for service, review this list. It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this appliance. OCCURRENCE POSSIBLE CAUSE/SOLUTION Range is not level.
Page 31
BEFORE YOU CALL (Solutions to Common Problems) OCCURRENCE POSSIBLE CAUSE/SOLUTION Scratches or Coarse particles such as salt or sand between cooktop and utensils can cause scratches. Be abrasions on sure cooktop surface and bottoms of utensils are clean before usage. Small scratches do not cooktop surface.
MAJOR APPLIANCE WARRANTY Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and maintained in accordance with the provided instructions.