Advertisement
initial setup
camera and power connections
step 1 ... Installing cameras
Mounting Cameras and Running Cable
Select the position for the camera and secure the camera stand. Screw the camera onto the stand. Adjust camera to the proper
view angle. Make sure the lens is upright relative to the subject. Tighten the thumb bolt. First Alert cameras can be either ceiling or
wall mounted by simply reversing the camera stand mounting. See "Camera Orientation" Info box. Holes are provided on both the
bottom and back of the camera housing to accommodate most mounting requirements. Run cable from camera to DVR location.
See Information box below on "Longer Cable Runs".
Camera - Wall Mounted
Camera - Ceiling Mounted
Step 2 ... connecting devices
Follow this diagram to make device connections. Note, some devices are
not included with this kit. See "What's in the Box" for included devices.
RCA Audio In from Audio
Smartphone
through Mobile
Internet Setup
(Smartphone Not
DVR Front Face
Connect Mouse &
included)
USB Drive
RJ45 Ethernet
to Router and
Internet
Splitter -
8 camera/
1 Power
Power
Power to Cameras
from 120V
DC Converter - 12V
Camera Orientation
It's important the camera is mounted correctly to
ensure the image is not upside down as the cam-
era lens can only be positioned one way.
Longer Cable Runs
Longer cable runs may require an upgrade to
RG59 Coax cable. First Alert kits ship with eco-
nomical AV cable that is designed to work well up
to the length of cable provided, usually around
60 feet. If longer distances between camera and
DVR are required, you will need to upgrade to RG59 Coax cable. We
provide several lengths up to 300 feet. In addition, if you need to run
cable for in-wall installations, then you may require fire rated cable,
FT-4/CMR UL approved for in-wall installations.
RCA Audio Out to
Powered Speakers
(Not included)
VGA to PC Monitor or TV
BNC to Security Camera Monitor
Cameras or Powered
(Not included)
Microphone
(Not included)
PTZ & Alarm
Power to DVR
Connections
(Cameras not
included)
Video to DVR
Channels 1-8
AV Cable: BNC/
DC Power
(1 per Camera)
Video to Camera
Power to Camera
Power to Camera
Page 6
Step 3 ... system start up
Power On/Off
To power the system On/Off, connect the power cable to the DC 12V port on the rear
panel. Flip the toggle switch on in the back of the DVR. At startup, the system performs
a basic system check and runs an initial loading sequence. After a few moments, the
system loads a live display view.
Default Video Output
The default video output for the DVR system is VGA. If you connect a BNC
(CVBS) monitor on initial setup, you will need to use the mouse "Scroll Wheel"
to switch to the BNC output to be able to use the mouse. Roll the mouse "Scroll
Wheel" backward to go to BNC and forward to go to VGA. The REMARK screen
is shown on startup.
Password
ATTENTION: By default, passwords are disabled on the system. You do not need
to enter a password when accessing any system menus. However, for security
purposes, it is highly recommended to enable passwords on the system using
the Password Menu. See "Password" section for details on setting up passwords.
Click APPLY to access the menus or click EXIT to cancel password setup and
return to the LIVE VIEW screen.
Standby Mode
The system can also be put into Standby Mode. Power will remain to the system but
will not be recording. To start/stop Standby Mode:
1.
Press and hold the POWER button on the front panel or remote control until the
prompt closes. The system enters standby mode. You can also enter Standby
mode through the Quick Access Menu. See below.
2.
To exit standby mode, press and hold the POWER button on the front panel
or remote control until the system beeps. The system will begin powering up.
Main Menu Access
To open the Main Menu: Right-click anywhere on-screen to open the Quick Access
Menu and select MAIN MENU (mouse only), or press the MENU button on the remote
control or front panel of the system.
Quick Access Menu
When using the mouse, use the Quick Access Menu to access several sys-
tem options, including the Main Menu. Select one of the following
options:
• MAIN MENU: Opens the main system menu
• KEYLOCK: Logs current user off the system. Re-login required.
• CHN SWITCH: Select type of split-screen display
• VIDEO SEARCH: Open the Search Menu to view recorded video
• PTZ : Opens the PTZ control menu
• MUTE: Mute listen-in audio on the system
• MANUAL REC: Start manual recording
• STOP REC: Stop manual recording
• ROTATION: Video rotation
• START CRUISE: Click to start preset PTZ Camera motion
• STOP CRUISE: Click to stop preset PTZ Camera motion
To close the Sub-Menu, click anywhere on-screen.
Quick Access Menu
NOTE: If passwords are enabled on the system, you need to select your Device ID and enter the 6-digit numerical password to open
the Main Menu.
Main Menu
1.
RECORD SEARCH: Search for recorded video on the system.
2.
RECORD: Configure recording parameters (quality, resolution), set record
modes, and enable/disable audio recording. Note: Audio capable cameras (not
included) are required for audio recording on the system.
3.
HDD: Display hard drive status and format the internal hard drive of the system.
4.
BASIC: Open the Basic Setup Menu, which lets you set the system language,
date and time, device IDs and passwords, and configure display, audio and
video settings.
5.
ADVANCED: Opens the Advanced Setup Menu. You can view system info, con-
figure alarm, PTZ, motion detect, maintenance, mobile, and network settings.
6.
EXIT: Closes the Main Menu.
7.
Displays information about the contents of the selected Main Menu icon.
initial setup
system operation
Switch between VGA to BNC Output
User Login Menu
No HDD installed
NOTE: If there is no HDD
installed, or the HDD is
not recognized, or the
HDD is not formatted
it will display a red【H】in the video
preview interface. You must format the
HDD in the DVR before first use. See:
Menu > HDD management > Format.
After formatting, the system will restart.
Main Viewing Screen
Showing No HDD in DVR
Main Menu
Page 7
Advertisement
