Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: www.sears.com/craftsman Save this manual for future reference 983000-760 7-05...
If this Craftsman tool fails to give complete satisfaction within one year from date of purchase, RETURN IT TO THE NEAREST SEARS STORE IN THE UNITED STATES, and Sears will replace it, free of charge. If this Craftsman tool is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase.
Use battery only with charger listed. power tools. Such preventive safety measures reduce MODEL BATTERY PACK CHARGER the risk of starting the power tool accidentally. 315.115760 130279003 Model No. 1425301 n Store idle power tools out of the reach of children 130279005 (Item No.
GENERAL SAFETY RULES n Use the power tool, accessories and tool bits etc., make a connection from one terminal to another. in accordance with these instructions and in the Shorting the battery terminals together may cause manner intended for the particular type of power burns or a fire.
SAFETY RULES FOR CHARGER could result in a risk of fire and electric shock. If WARNING! READ AND UNDERSTAND ALL extension cord must be used, make sure: INSTRUCTIONS. Failure to follow all instructions a. That pins on plug of extension cord are the listed below, may result in electric shock, fire same number, size and shape as those of and/or serious personal injury.
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION Volts Voltage Amperes Current Hertz Frequency (cycles per second)
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING Indicates an imminently hazardous situation, which, if not avoided, will DANGER: result in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, could WARNING: result in death or serious injury.
FEATURES PRODUCT SPECIFICATIONS Chuck ................................3/8 in. Keyless Motor ...................................19.2 Volt DC Switch................................Variable Speed No Load Speed ..............................0-1,050/min. Charger Input ............................120 V, 60 Hz, AC only Charge Rate ..................................1 hour Torque..................................150 in.lb. KEYLESS CHUCK WORKLIGHT SWITCH TRIGGER DIRECTION OF ROTATION SELECTOR (FORWARD/REVERSE/...
FEATURES KNOW YOUR RIGHT ANGLE DRILL-DRIVER LED WORKLIGHT See Figure 1. The LED worklight, located below the chuck, illuminates Before attempting to use this product, familiarize yourself when the switch trigger is depressed. This provides extra with all operating features and safety rules. light for increased visibility.
OPERATION CHARGING THE BATTERY PACK WARNING: Do not allow familiarity with tools to Battery packs for this tool are shipped in a low charge make you careless. Remember that a careless condition to prevent possible problems. Therefore, you fraction of a second is sufficient to inflict serious should charge it until the green LED on the front of the injury.
OPERATION n Red LED should remain on for approximately 1 hour TO INSTALL BATTERY PACK then the green LED will come on. Green LED on See Figure 3. indicates battery pack is fully charged and charger is n Lock the switch trigger on the drill by placing the direc- in maintenance charge mode.
OPERATION SCREWDRIVER WARNING: Make sure to insert the drill bit straight into the chuck jaws. Do not insert the drill bit into the chuck jaws at an angle then tighten, as shown in fig- ure 8. This could cause the drill bit to be thrown from STORAGE AREA the drill, resulting in possible serious personal injury or damage to the chuck.
OPERATION DRILLING LED WORKLIGHT See Figure 9. See Figure 10. The LED worklight, located below the chuck, illuminates n Check the direction of rotation selector for the correct when the switch trigger is depressed. This provides setting (forward or reverse). additional lighting on the surface of the workpiece for n Secure the material to be drilled in a vise or with operation in lower-light areas.
WARNING: When servicing, use only identical Do not at any time let brake fluids, Craftsman replacement parts. Use of any other part gasoline, petroleum-based products, penetrating may create a hazard or cause product damage. oils, etc., come in contact with plastic parts. Chemi- cals can damage, weaken or destroy plastic which may result in serious personal injury.
MAINTENANCE CHUCK REMOVAL n Insert the hex key in chuck and tighten the chuck jaws securely. Tap sharply with a mallet in a counter- See Figures 11 - 13. clockwise direction. This will loosen the chuck on the The chuck may be removed and replaced by a new one. spindle.
CRAFTSMAN RIGHT ANGLE DRILL-DRIVER MODEL NUMBER 315.115760 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your RIGHT ANGLE DRILL-DRIVER or when ordering repair parts. SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS...
Get it fixed, at your home or ours! Your Home For repair – in your home – of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner’s manuals that you need to do-it-yourself.