Advertisement
Available languages
Available languages
,0
iiiiiiiiiiiiiii_i;_iiii!ii:i_iiiilililili_ii_ii_ii_ii_ii_ii_ii_ii{!;!!!j!ij
iiiiiiiiiiiiii::i_'iiiii_:ii:ii:ii:ii:iiiiii!ii!!
iiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiililililililililiiiiiiii i!ill
,0
,0
-€
#_.
About theautomaticieemake
A newly instafled refrigerator may take 12 to 24 hours to begin making ice.
Automatic Icemaker
On dispenser models,
to access ice or reach
the power switch:
o
Lift the bin, then pull it
forward until the bin stops.
Lower the bin to access ice
or reach the power switch.
NOTE:In order to take full advantage
of the tilt-out ice bin, only store items
on the shelf below the ice bfl? that
are no taller than the Iowest point
on the bh_.
Tile icemaker
will produce
seven cubes
per cycle---aI)I)ro_mately
] 00-130
cubes
in a 94-hem" period,
depending
on fl'eezer
COilli)ai'tlllent
teillpei'attli'e_
i'OOill
temperatm'e,
nmnber
ot door openings
and other
use conditions.
If tile refl_igerator
is operated
betore
tile
water connect.ion
is made
to the icemaket;
set tile power switch in tile 0 (Of/) position.
When
the reti-igerator
has been
com_ected
to tile water SUl)l)ly, set tile power switch to
tile I (on) position.
The icemaker
will fill with water when it
cools to ] 5°F (-10°C).
A newly installed
refi_igemtor may take 12 to 24 hems to begin
making
ice cubes.
You will hear a buzzing
so/md
each time
the icemaker
fills with water
Throw
awax tile first troy batches
of ice to
allow the water line to clea_:
Be sm'e nothing
interteres
with tile sweep
of tile teeler amL
When
tile bin fills to tile level ot tile teeler
am_, tile icemaker
will stop producing
ice. It is nom_al tin" several cubes to be
joined
together.
If ice is not used fl'equentl>
old ice cubes
will become
cloudy, taste stale and shrink.
Special note about dispenser models:
Dispenser
models
have a tilt-out ice bin.
The bin can be tilted out as shown in the
illustrations,
and it will hold itself up
while you take ice out or tm'n tile
icemaker
power switch on and off'. Be
sm'e to put tile bin back in place before
closing the doo_:
To restore
your ice level from an empty
bucket
stage, the following
steps are
recommended:
12 ho/us
after the first batch
of ice
has fifllen into the bin, dispense
3 to 4 cubes.
@
_MteI" an additional
6 hom_, dispense
3 to 4 cubes again.
These steps will restore
your ice level
in the shortest
amount
of time.
Power
Switch
!cemaker
green
PowerLight
Feeler A rm
NOTE:/n homes with lower-than-averagewater
pressure,you may hear the icemakercycle mult_}91e
t_meswhen mak/bg onebatch of ice.
i i
o
Lift thebin, thenpull it
forward untilthe bin stops.
o
Lift andpull forwardagain
to removethe bin.
Removing Ice Bin (dispensermodels)
gAUTlON: The ice bin is heavy when full.
SettheI,o,,'e,'switdl to theOtomI,ositi..
before relnoxing
tile bin.
When replacing the bin, be sure to press it
firefly into place. If it does not go all tile
wa) back, remoxe
it and rotate
tile (lrixe
backmechanism
again.
1/4 turn. Then
push tile bin
Dispenser Models only
14
Advertisement
