Level Cal (Level Calibration); Audio Adjust - Onkyo HT-S5600 Owner's Manual

6. Level Cal (Level Calibration)

1 2 3 4
Menu Level Cal
This setting is set automatically by Audyssey 2EQ
Room Correction and Speaker Setup
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
Note
• These settings cannot be calibrated in either of the following
cases:
– A pair of headphones is connected.
– The "Audio TV Out" setting is set to "On"
– "HDMI CEC (RIHD)" is set to "On" (➔ page
you're listening through your TV speakers.
– The AV receiver is muted.
■
Left, Front High Left, Center , Front High Right,
*1
Right, Surround Right, Surr Back Right, Surr
Back Left, Surround Left
–12 dB to 0 dB to +12 dB in 1 dB step.
■
Subwoofer *1
–15 dB to 0 dB to +12 dB in 1 dB step.
Note
• Speakers that you set to "No" or "None" in the "4. Sp Config
(Speaker Configuration)" (➔ page 39) cannot be selected.
• When the "Powered Zone 2" setting is set to "Yes" and Zone 2
is turned on, the surround back and front high speakers cannot be
used.
*1 For the center speaker and subwoofer, the level settings made
by using the Home menu are saved in this menu
Tip
• If you're using a handheld sound level meter, adjust the level of
each speaker so that it reads 75 dB SPL at the listening position,
measured with C-weighting and slow reading.

7. Audio Adjust

5 6 1 2
Menu
With the Audio Adjust functions and settings, you can
®
adjust the sound and listening modes as you like.
(➔ page 26).
Multiplex/Mono
■
Multiplex
Input Ch (Mux)
Main
Sub
Main/Sub
(➔ page 46).
This setting determines which channel of a stereo
46) and
multiplex source is output. Use it to select audio channels
or languages with multiplex sources, multilingual TV
broadcasts, and so on.
■
Mono
Input Ch (Mono)
Left + Right
Left
Right
This setting specifies the channel to be used for playing
any 2-channel digital source such as Dolby Digital, or 2-
channel analog/PCM source in the Mono listening mode.
(➔ page 47).
3 4 5 6
Audio Adjust
En-41
Advanced Operations
Dolby
■
PL IIx Music (2ch Input)
These settings apply to only 2-channel stereo sources.
If you're not using any surround back speakers, these
settings apply to Dolby Pro Logic II, not Dolby Pro Logic
IIx.
Panorama
On
Off
With this setting, you can broaden the width of the front
stereo image when using the Dolby Pro Logic IIx Music
listening mode.
Dimension
–3 to 0 to +3
With this setting, you can move the sound field forward or
backward when using the Dolby Pro Logic IIx Music
listening mode. Higher settings move the sound field
backward. Lower settings move it forward.
If the stereo image feels too wide, or there's too much
surround sound, move the sound field forward to improve
the balance. Conversely, if the stereo image feels like it's
in mono, or there's not enough surround sound, move it
backward.
Center Width
0 to 3 to 7
With this setting, you can adjust the width of the sound
from the center speaker when using the Dolby Pro Logic
IIx Music listening mode. Normally, if you're using a
center speaker, the center channel sound is output from
only the center speaker. (If you're not using a center
speaker, the center channel sound will be distributed to the
front left and right speakers to create a phantom center).
This setting controls the front left, right, and center mix,
allowing you to adjust the weight of the center channel
sound.