Adapter Port Terminal; Video; Settings - Pioneer Elite VSX-70 Operating Instructions Manual

13

ADAPTER PORT terminal

Symptom Remedy
The Bluetooth wireless technology Check that no object that emits electromagnetic waves in the 2.4 GHz band (microwave
device cannot be connected or oper- oven, wireless LAN device or Bluetooth wireless technology apparatus) is near the unit. If
ated. Sound from the Bluetooth wire- such an object is near the unit, set the unit far from it. Or, stop using the object emitting
less technology device is not emitted the electromagnetic waves.
or the sound is interrupted.
Check that the Bluetooth wireless technology device is not too far from the unit and that
obstructions are not set between the Bluetooth wireless technology device and the unit.
Set the Bluetooth wireless technology device and the unit so that the distance between
them is less than about 10 m (33 ft.) and no obstructions exist between them.
Check that the Bluetooth ADAPTER and the ADAPTER PORT of the unit are correctly
connected.
The Bluetooth wireless technology device may not be set to the communication mode
supporting the Bluetooth wireless technology. Check the setting of the Bluetooth wireless
technology device.
Check that pairing is correct. The pairing setting was deleted from this unit or the Blue-
tooth wireless technology device. Reset the pairing.
Check that the profile is correct. Use a Bluetooth wireless technology device that supports
A2DP profile and AVRCP profile.
The Air Jam function cannot be Disconnect the iPod from this receiver (see
used.

Video

Symptom Remedy
No image is output when an input is Check the video connections of the source component.
selected.
For HDMI, or when V.CONV is set to OFF and a TV and another component are con-
nected with different cords (in
your TV to this receiver using the same type of video cable as you used to connect your
video component. For the component video input, however, signals are only output from
the HDMI output, so when using the component video input, set V.CONV to ON.
Make sure the input assignment is correct for components connected using component
video or HDMI cables (see
Check the video output settings of the source component.
Check that the video input you selected on your TV is correct.
Some components (such as video game units) have resolutions that may not be con-
verted. If adjusting this receiver's Resolution setting (in
65) and/or the resolution settings on your component or display doesn't work, try switch-
ing V.CONV (in
Can't record video. Check that the source is not copy-protected.
The video converter is not available when making recordings. Check that the same type
of video cable is used for connecting both the recorder and the video source (the one you
want to record) to this receiver.
Noisy, intermittent, or distorted Sometimes a video deck may output a noisy video signal (during scanning, for example),
picture. or the video quality may just be poor (with some video game units, for example). The
picture quality may also depend on the settings, etc. of your display device. Switch off
the video converter and reconnect the source and display device using the same type of
connection (component or composite), then start playback again.
Air Jam on page 47).
Setting the Video options on page 65), you must connect
The Input Setup menu on page 37).
Setting the Video options
Setting the Video options on page 65) to OFF.
Symptom Remedy
Video signals are not output from the When a monitor only compatible with resolutions of 480i is connected to the component
component terminal. terminal and another monitor is connected to the HDMI terminal, the video signals may
not be output to the monitor connected to the component terminal. If this happens, do
the following:
— Turn off the power of the monitor connected to the HDMI terminal.
— Change the VIDEO PARAMETER menu RES setting (see
page
— Video signals from the HDMI terminal cannot be output to the component terminals.
Input the video signals from the player or other source to the composite or component
terminals. When using the component terminal, assign it at Input Setup (see
Setup menu
The picture's movement is unnatural. When Resolution under VIDEO PARAMETER is set to 1080/24p, the picture may not be
displayed properly for some source materials. In this case, set the resolution to some-
thing other than 1080/24p

Settings

Symptom Remedy
The Auto MCACC Setup continually The ambient noise level may be too high. Keep the noise level in the room as low as
shows an error. possible (see also
level cannot be kept low enough, you will have to set up the surround sound manually
(page
When using only one surround back speaker, connect it to the SURROUND BACK L
(Single) terminals.
To use a 5.1-channel speaker set, use the surround speakers for the surround channel,
not the surround back channel.
Make sure there are no obstacles between the speakers and the microphone.
If Reverse Phase is displayed, try the following:
— The speaker's wiring (+ and –) may be inverted. Check the speaker connections.
— Depending on the type of speakers and their installation conditions, Reverse Phase
may be displayed even if the speakers are properly connected. If this happens, select
GO NEXT and continue.
— If the speaker is not pointed to the microphone (listening position) or when using
speakers that affect the phase (dipole speakers, reflective speakers, etc.), it may not be
possible to properly identify the polarity.
After using the Auto MCACC Setup, There may have been some low frequency noise in the room from an air-conditioner,
the speaker size setting is incorrect. motor, etc. Switch off all other appliances in the room and use Auto MCACC Setup again.
Depending on a number of factors (bass reproduction capabilities of the speakers, room
on page
size, speaker placement, etc.) this may occur in some cases. Change the speaker setting
manually in
the Auto MCACC menu in
problem.
Can't adjust the Fine Speaker Dis- Check that the speakers are all in phase (make sure the positive (+) and negative (–)
tance setting properly. terminals are matched up properly).
The display shows KEY LOCK ON
With the receiver in standby, press u STANDBY/ON for about 5 seconds while holding
when you try to make settings. down SPEAKERS to disable the key lock.
Most recent settings have been The power cord was disconnected from the wall while adjusting this setting.
erased.
Settings are only stored if all the zones are turned off. Turn off all the zones before unplug-
ging the power cord.
95
Setting the Video options
65).
on page 37).
(page 65).
Problems when using the Auto MCACC Setup
84).
Speaker Setting on page 84, and use the ALL (Keep SP System) option for
Automatic MCACC (Expert) on page 77
FAQ
on
The Input
on page 37). If the noise
if this is a recurring