Making An Audio Or A Video Recording; Network Settings From A Web Browser - Pioneer Elite SC-89 Operating Instructions Manual

09
ZONE 2 remote controls
Before operation, hold down Z2 on the remote control (for 1.5 seconds) until the remote control LED flashes one
time.
The following table shows the possible ZONE 2 remote controls:
Button(s) What it does
Switches on/off power in the sub zone.
u
ALL Use to select the input function in the sub zone.
Use to select the input function directly (this may not work for some functions) in the sub
Input function buttons
zone.
VOLUME +/–
Use to set the listening volume in the sub zone.
<a>
MUTE Mutes the sound or restores the sound if it has been muted (adjusting the volume also
<a> restores the sound).
a ! The volume cannot be adjusted on the receiver if Volume Level at ZONE 2 Setup under ZONE Setup is set to –40 dB Fixed
or 0 dB Fixed.
ZONE 3 remote controls
Press the remote control's Z3 to operate the corresponding zone.
The following table shows the possible ZONE 3 remote controls:
Button(s) What it does
Switches on/off power in the sub zone.
u
ALL Use to select the input function in the sub zone.
Use to select the input function directly (this may not work for some functions) in the sub
Input function buttons
zone.
VOLUME +/–
Use to set the listening volume in the sub zone.
<a>
MUTE Mutes the sound or restores the sound if it has been muted (adjusting the volume also
<a> restores the sound).
a ! The volume cannot be adjusted on the receiver if Volume Level at ZONE 3 Setup under ZONE Setup is set to –40 dB Fixed
or 0 dB Fixed.
HDZONE remote controls
Before operation, hold down HDZ on the remote control (for 1.5 seconds) until the remote control LED flashes
one time.
The following table shows the possible HDZONE remote controls:
Button(s) What it does
Switches on/off power in the HDZONE.
u
ALL Use to select the input function in the HDZONE.
Use to select the input function directly (this may not work for some functions) in the
Input function buttons
HDZONE.
VOLUME +/–
Use to set the listening volume in the HDZONE.
<a>
MUTE Mutes the sound or restores the sound if it has been muted (adjusting the volume also
<a> restores the sound).
a You can operate this only when Speaker System is set to 7.2ch + HDZONE, 5.2 Bi-Amp+HDZONE or 5.2 +ZONE 2+HDZONE.

Making an audio or a video recording

You can make an audio or a video recording from the built-in tuner, or from an audio or video source connected to
the receiver (such as a CD player or TV).
Keep in mind you can't make a digital recording from an analog source or vice-versa, so make sure the compo-
nents you are recording to/from are hooked up in the same way (see
for more on connections).
! The receiver's volume, Audio parameters (the tone controls, for example), and surround effects have no effect
on the recorded signal.
! Some digital sources are copy-protected, and can only be recorded in analog.
! Some video sources are copy-protected. These cannot be recorded.
Since the video converter is not available when making recordings (from the video OUT jacks) make sure to use
the same type of video cable for connecting your recorder as you used to connect your video source (the one you
want to record) to this receiver. For example, you must connect your recorder using Component video if your
source has also been connected using Component video.
1 Select the source you want to record.
You can use the input function buttons on the remote control or the front panel INPUT SELECTOR dial.
2 Prepare the source you want to record.
Tune to the radio station, load the CD, video, DVD etc.
3 Select the input signal according to the signal to be recorded.
Use the remote control's AUDIO P. button.
4 Prepare the recorder.
Insert a blank tape, MD, video etc. into the recording device and set the recording levels. Refer to the instructions
that came with the recorder if you are unsure how to do this. Most video recorders set the audio recording level
automatically-check the component's instruction manual if you're unsure.
5 Start recording, then start playback of the source component.

Network settings from a web browser

Network settings and Pandora account settings can be made using the browser on a computer connected to the
same LAN as the receiver.
1 Press u STANDBY/ON to switch on the receiver.
2 Turn on the computer's power and launch the Internet browser.
3 Input the receiver's IP address into the browser's address input field.
Access the IP address"http://(the receiver's IP address)" from a web browser. You can display the IP address of
the unit on the unit's display by pressing the STATUS button on the remote control.
When connected with the receiver, the AVNavigator menu screen appears in the browser.
4 On the AVNavigator menu screen, select Network Setup.
5 Select the item you want to set.
88
Using other functions
Connecting your equipment on page 20