Hookups; Dvd/Vcr To Tv Connection; Setting The Ch3/Ch4 Switch; Connecting To A Tv - Emerson EWD2202 Owner's Manual

DVD/VCR TO TV CONNECTION

1. Disconnect the AC power cord of the TV from the
AC outlet.
2. Disconnect the antenna or cable from the TV.
3. Connect the antenna or cable to the ANT-IN jack of
the DVD/VCR.
4. Connect the DVD/VCR to the TV using the coaxial
cable.
5. Plug the AC power cords of the DVD/VCR and TV
into the AC outlets.
[VHF/UHF
[Indoor antenna]
combination antenna]
[Cable box or satellite box]
IN
OUT
From Cable or
Satellite Company
Note to CATV system installer
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that pro-
vides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected
to the grounding system of the building, as close to the point of cable entry as practical.
Antenna/Cable signal
A/V-compatible or
wide screen TV
Notes
¡
Connect the DVD/VCR directly to a TV. If the A/V cables are connected to a VCR, pictures may be
distorted due to the copy protection system.
S-VIDEO INPUT JACK OR COMPONENT VIDEO IN JACKS
FOR TVs WITH S-VIDEO INPUT JACK
Use an S-Video cable (commercially available) in place of the yellow video cable to enjoy higher quality pic-
tures.
The S-Video connection only supplies video (picture) in the DVD mode of the DVD/VCR. Therefore, in order to
use the VCR features or view TV channels on the DVD/VCR, you still need to either connect the RF coaxial cable
between the ANT-OUT jack of the DVD/VCR and the TV's Antenna In jack, or connect the yellow video cable as
described earlier (Fig.1). To connect the supplied RF coaxial cable, see "DVD/VCR TO TV CONNECTION"
above.
A/V-compatible or
wide screen TV

HOOKUPS

[Back of the DVD/VCR]
[Back of the
UHF/VHF combination TV]
Coaxial cable
OR
ANT - IN
(supplied)
UHF/VHF
OR
ANT - OUT
CH3 CH4

CONNECTING TO A TV

ANT - IN
ANT - OUT
CH3 CH4
To ANT. IN
of TV
To VIDEO INPUT jack
To Right (red) and Left (white)
AUDIO INPUT jacks
CONNECTING TO A TV THAT HAS AN
ANT - IN
ANT - OUT
CH3 CH4
To Right (red) and Left (white)
AUDIO INPUT jacks
To S-VIDEO INPUT jack
SETTING THE CH3/CH4
If your TV does not have A/V terminals:
When the DVD/VCR is in the VCR Playback mode or
when the DVD/VCR is in the VCR mode, your TV will
receive signals from the DVD/VCR on either channel
3 or channel 4. To use the DVD/VCR with your TV, set
the selector switch to CH3 or CH4 (which is located in
the back of your DVD/VCR), whichever is not used for
normal broadcasts in your area. Then set your TV to
the same channel.
DVD/VCR
OUT
IN
L
AUDO
R
VIDEO
To VIDEO OUT jack
AUDIO OUT jacks
DVD/VCR
OUT
IN
L
AUDO
R
VIDEO
AUDIO OUT jacks
To S-VIDEO OUT jack
– 14 –
SWITCH
ANT - IN
CH3 CH4
ANT - OUT
CH3 CH4
[Back of the DVD/VCR]
COMPONENT
VIDEO OUT
Y
DVD/VCR
AUDIO OUT
DIGITAL AUDIO OUT
S-VIDEO
L
Cb
PCM / BITSTREAM
OUT
COAXIAL
R Cr
COMPONENT
VIDEO OUT
Y
DVD/VCR
AUDIO OUT
DIGITAL AUDIO OUT
S-VIDEO
L
Cb
PCM / BITSTREAM
OUT
COAXIAL
R Cr
[Fig. 1]
[Fig. 2]
EN
1L25