Customer Support Overview If you experience difficulties after reading the manual and/or using the product, contact the Connect Tech reseller from which you purchased the product. In most cases the reseller can help you with product installation and difficulties. In the event that the reseller is unable to resolve your problem, our highly qualified support staff can assist you.
Connect Tech Inc.'s opinion, fail to be in good working order during the warranty period, Connect Tech Inc. will, at its option, repair or replace this product at no charge, provided that the product has not been subjected to abuse, misuse, accident, disaster or non-Connect Tech Inc.
Connect Tech Xtreme/SBC PCIe/104 Single Board Computer and PCIe/104 Qseven Carrier Board - User Manual Introduction Connect Tech’s Xtreme/SBC is a small embedded carrier board that utilizes the PCI/104-Express form factor, which has the standard PC/104 dimensions with 4 x1 PCIe lanes. This carrier board includes the required connectors and cables for easy connection to 2x SATA, 2x RS-232, 2x RS- 422/485, 4x USB 2.0, 1x Gigabit Ethernet, LVDS and VGA Video.
Connect Tech Xtreme/SBC PCIe/104 Single Board Computer and PCIe/104 Qseven Carrier Board - User Manual System Block Diagram The Qseven module implements the core processing features including: processor, memory, and system physical interfaces via the southbridge. Many of the Qseven modules are based on the mobile Intel Atom architecture (Z series processor + Poulsbo / SCH US15W chipset);...
Connect Tech Xtreme/SBC PCIe/104 Single Board Computer and PCIe/104 Qseven Carrier Board - User Manual Qseven Module Interface Description The processor and Chipset are implemented on the Qseven CPU module, which connects to the Xtreme/SBC via a MXM connector. As previously mentioned, many of the existing Qseven Modules use the Intel Atom mobile architecture, Z series processor + Poulsbo / SCH US15W chipset.
Connect Tech Xtreme/SBC PCIe/104 Single Board Computer and PCIe/104 Qseven Carrier Board - User Manual LVDS Description Xtreme/SBC provides dual 18 or 24 bit LVDS display channels via P7, which are connected directly from the Qseven module . LVDS panel supply power is selected with jumper J4 and backlight power is selected with jumper J6.
Page 11
Connect Tech Xtreme/SBC PCIe/104 Single Board Computer and PCIe/104 Qseven Carrier Board - User Manual Function LVDS backlight power Location Hirose DF13-8P-1.25H connector Type Pinout Signal Description +12V +12 V DC, max. 1A +12V +12 V DC, max. 1A +5 V DC, max. 1A +5 V DC, max.
Connect Tech Xtreme/SBC PCIe/104 Single Board Computer and PCIe/104 Qseven Carrier Board - User Manual Function LVDS backlight enable polarity Selects either positive or negative. Refer to the inverter power supply documentation for proper configuration. Location Type 1x2 2mm jumper block...
Connect Tech Xtreme/SBC PCIe/104 Single Board Computer and PCIe/104 Qseven Carrier Board - User Manual USB 2.0 Description The Xtreme/SBC implements 4 of the 8 available USB 2.0 connections via two connectors. Over current protection and power supply filtering is provided.
Connect Tech Xtreme/SBC PCIe/104 Single Board Computer and PCIe/104 Qseven Carrier Board - User Manual Connector & LEDs Function SATA host Locations P10A, P10B P10A Industry standard right angle sata host Type connector Molex 0470804005 (or equivalent) Pinout Signal SATA_TX_P...
Connect Tech Xtreme/SBC PCIe/104 Single Board Computer and PCIe/104 Qseven Carrier Board - User Manual PCI-104 top mount – mechanical only, does Function not carry signals Locations P12 Industry standard Type EPT 264-60303-02 Connector is not populated by default. Note Can be installed on request.
Connect Tech Xtreme/SBC PCIe/104 Single Board Computer and PCIe/104 Qseven Carrier Board - User Manual Serial Description Two RS232 serial ports are provided on P9 and two RS485 serial ports are provided on P11. For the RS485 ports, the default configuration is full duplex without any bias or termination. Various resistors configurations can be populated to enabled TX and RX termination as well as RTS control.
Connect Tech Xtreme/SBC PCIe/104 Single Board Computer and PCIe/104 Qseven Carrier Board - User Manual PS/2 Keyboard and Mouse Description A PS/2 keyboard and PS/2 mouse interface are provided via P13; where the PS/2 voltage is selectable with J1. Refer to the specification printed on the bottom of the keyboard and mouse to determine which voltage to select;...
Connect Tech Xtreme/SBC PCIe/104 Single Board Computer and PCIe/104 Qseven Carrier Board - User Manual Power Description The Xtreme/SBC is designed to be powered from an ATX type power supply, and support many of the ACPI features like suspend to RAM. A CR1225 battery holder (P16) provides the VBAT for the Qseven module.
Page 21
Connect Tech Xtreme/SBC PCIe/104 Single Board Computer and PCIe/104 Qseven Carrier Board - User Manual Function Suspend Selection Selects either S3 or S5. Location Type 1x3 2 mm Pinout Position Description Suspend S3 Suspend S5 Floating Default Function Power Supply on...
Connect Tech Xtreme/SBC PCIe/104 Single Board Computer and PCIe/104 Qseven Carrier Board - User Manual Fan Control Description If actively cooling is required; P14 can be used to power and control a fan with J2 selecting the fan voltage. Connectors & Jumpers...
Connect Tech Xtreme/SBC PCIe/104 Single Board Computer and PCIe/104 Qseven Carrier Board - User Manual Battery Description A CR1225 battery holder is provided at P16. This is a standard 3V battery, which powers the RTC (real time clock) on the CPU module. In most cases, it is not required to preserve critical BIOS settings as most Qseven modules have a flash based BIOS.
Connect Tech Xtreme/SBC PCIe/104 Single Board Computer and PCIe/104 Qseven Carrier Board - User Manual Connect the appropriate I/O peripherals to the interface cables: keyboard, mouse, Ethernet, monitor, etc. Connect the power cable to power supply Turn on the supply.
Cables & Interconnect The following table summarizes the Xtreme/SBC’s headers and lists the matching cables included with the optional cable kit CKG001. Location PCB Connector Cable Part Drawing Description PCB End Interface End Number Number P3A, P3B Hirose CBG071 CTIC-00182 USB (dual) Hirose USB 2.0 Type A female...
Need help?
Do you have a question about the Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board and is the answer not in the manual?
Questions and answers