Hitachi SJ300-EL Series Instruction Manual Supplement page 27

Function mode
Code Function name
C001 Intelligent input 1 setting
C002 Intelligent input 2 setting
C003 Intelligent input 3 setting
C004 Intelligent input 4 setting
C005 Intelligent input 5 setting
C006 Intelligent input 6 setting
C007 Intelligent input 7 setting
C008 Intelligent input 8 setting
Intelligent input 1 a/b (NO/NC)
C011
selection
Intelligent input 2 a/b (NO/NC)
C012
selection
Intelligent input 3 a/b (NO/NC)
C013
selection
Intelligent input 4 a/b (NO/NC)
C014
selection
Intelligent input 5 a/b (NO/NC)
C015
selection
Intelligent input 6 a/b
C016
(NO/NC) selection
Intelligent input 7a/b
C017
(NO/NC) selection
Intelligent input 8 a/b
C018
(NO/NC) selection
Input FW a/b (NO/NC)
C019
Selection
C021 Intelligent output 11 setting
C022 Intelligent output 12 setting
C023 Intelligent output 13 setting
C024 Intelligent output 14 setting
C025 Intelligent output 15 setting
C026 Alarm relay output
C027 FM selection
C028 AM selection
C029 AMI selection
C031 Intelligent output 11 a/b
C032 Intelligent output 12 a/b
C033 Intelligent output 13 a/b
C034 Intelligent output 14 a/b
C035 Intelligent output 15 a/b
C036 Alarm relay output a/b
Setting range
01/(RV:Reverse is valid)/02(CF1:Multi-speed1)/ 03(CF2:Multi-speed2)/
04(CF3:Multi-speed3)/07(DB:External DC braking)/
09(2CH:two-stage adjustable speed)/ 11(FRS:Free-run)/
12(EXT:External trip)/13(USP:Unattended start protection)/
14(CS:commercial change)/15(SFT:software lock)/
16(AT:Analog input voltage/current select)/18(RS:Reset inverter)/
20(STA:3wire run)/ 21(STP:3wire keep)/ 22(F/R:3wire forward/reverse)/
26(CAS:Control gain switch function)/
31(OPE:Operating by operator select)/ 32(SF1:Multi-speed bit1)/
33(SF2:Multi-speed bit2)/ 34(SF3:Multi-speed bit3)/
35(SF4:Multi-speed bit4)/36(SF5:Multi speed bit5)/
37(SF6:Multi-speed bit6)/ 38(SF7:Multi-speed bit7)/
39(OLR:Overload restriction change) / 40(TL:Torque limit select)/
41(TRQ1:Torque limit switch 1)/42(TRQ2:Torque limit switch 2)/
43((PPI:P/PI switch)/44(BOK:Braking comformation)/
45(ORT:Orientation)/ 46(LAC:LAD cancel)/
47(PCLR:Position error clear)/ 48(STAT: Permission of pulse train)/
50(SSD:Torque bias hold)/52(ECM:Changeover in case of emergency)/
no (NO: No assign)
00(NO)/01(NC)
00(NO)/01(NC)
00(NO)/01(NC)
00(NO)/01(NC)
00(NO)/01(NC)
00(NO)/01(NC)
00(NO)/01(NC)
00(NO)/01(NC)
00(NO)/01(NC)
00(RUN: running) / 01(FA1:Frequency arrival type1 signal) /
02(FA2:over setting frequency) / 03(OL: Overload advance notice signal)/
05(AL: Alarm signal)/06(FA3:Only setting frequency) /
07(OTQ: Over-torque signal) / 08(IP: On instantaneous stop) /
09(UV: Under voltage) / 10(TRQ: Torque limit)/
11(RNT: RUN time over) / 12(ONT:ON time over) / 13(THM: thermal caution) /
19(BRK: Brake release signal) / 20(BER: Brake error signal) /
21(ZS: Zero speed detect signal)/22(DSE: Speed error over signal) /
23(POK: Positioning completion signal)/24(FA4:Over frequency 2 signal)/
25(FA5: Only setting frequency) /
26(OL2: Overload advance notice signal (2)
(Intelligent output terminal 11-13 or 11-14 becomes AC0-AC2 or AC0-AC3
(Can: Alarm code output) forcibly when alarm code output is selected in C062)
00(Output frequency)/01(Output current) /02(Output torque)/
03(Digital output frequency)/04(Output voltage)/
05(Input electric power)/06(thermal load rate)/07(LAD frequency)
00(Output frequency)/01(Output current)/02(Output torque)/
04(Output voltage)/05(Input electric power)/06(thermal load rate)/
07(LAD frequency)
00(Output frequency)/01(Output current)/02(Output torque)/
04(Output voltage)/05(Input electric power)/
06(Thermal load rate)/07(LAD frequency)
00(NO)/01(NC)
00(NO)/01(NC)
00(NO)/01(NC)
00(NO)/01(NC)
00(NO)/01(NC)
00(NO)/01(NC)
27
Chapter 3 – Parameter Setting Tables
Initial data
18(RS)
15(SFT)
09(2CH)
11(FRS)
04(CF3)
03(CF2)
02(CF1)
01(RV)
00
00
00
00
00
00
00
00
00
01(FA1)
00(RUN)
03(OL)
19(BRK)
21(ZS)
05(AL)
00
00
00
00
00
00
00
00
01
remarks