Problems And Solutions For Programmed Recordings; Programming A Recording (Without Video Plus+) - Hitachi VTMX110EUK Operating Instructions Manual

5 The decoded data appears after confirmation. You can go
back to change the data. Select the corresponding input
field using P or Q
;P+ , P- = or with the number buttons
Switching on 'VPS/PDC' in the 'START' input field
Select the 'START' input field using
switch on 'VPS/PDC' (']' lights up). If you press
SELECT
again, you will switch 'VPS/PDC' off (']' goes out).
SELECT
6 When all informations are correctly, confirm with
The programming information is stored in a TIMER block.
7 Insert a cassette with an intact security tab (unprotected).
8 Switch off with
STANDBY m
The programmed recording will only function when the
video recorder is switched off with
If any of the TIMER blocks are in use, '
the video recorder display.
Problems and solutions for
programmed recordings
The video recorder will not operate
* While a programmed recording is being made, you cannot
operate your video recorder manually. If you want to cancel
the programmed recording, press
'SWITCH TO STANDBY- TIMER RECORDING' flashes on
the TV screen
* The video recorder was switched on several minutes
before the start of a programmed recording.
Switch off the video recorder with
programmed recording (timer) will only function if the video
recorder is switched off.
Cassette is ejected during recording
* The end of the tape was reached during recording.
Error message: 'NO CASSETTE'
recorder display
* No cassette was inserted. Insert a cassette and switch off
the video recorder using
Cassette was ejected as soon as the
pressed
* A cassette was inserted with the security tab removed.
Undo the erase protection (chapter 'Manual Recording',
section 'Preventing accidental erasing of cassettes') or
insert a different cassette.
Error message: 'ALL TIMERS OCCUPIED'
* If this error message appears after pressing
all TIMER blocks are already programmed. No more
recordings can be programmed. If you want to clear a
programmed recording (TIMER block), select it with
;P+ or P- = and then press
22
. Change the data with
.
0-9
P . Using
OK
.
STANDBY m
k
' will light up on
STANDBY m .
STANDBY m
. A
k ' will flash in the video
STANDBY m .
button was
OK
TIMER
.
CLEAR (CL)
Programming a recording
(without VIDEO Plus+)
1 Switch on the TV set. If required, select the programme
number for the video recorder.
2 Press
TIMER
TIMER block will be highlighted.
3 Press
TIMER
.
screen.
TIMER
DATE
21
.
________________________________
REP.pSELECT
4 With
TIMER
(date), 'PROG.' (programme number), 'START' (start time)
and 'END' (end time).
Enter or change your information with
or with the number buttons
Selecting onetime/daily/weekly recordings
In 'DATE' use
SELECT
'ONCE': Recording once
'MO-FR': Repeated daily recordings from Monday to Friday
'WEEK.': Repeated weekly recordings (every week on the
same day)
Programme numbers of the 'E1' and 'E2' scart socket
You can also programme recordings from external sources
via scart socket
'Switching on 'VPS/PDC' in the 'START' input field
Select the 'START' input field using
switch on 'VPS/PDC' (']' lights up). If you press
SELECT
again, you will switch 'VPS/PDC' off (']' goes out).
SELECT
5 When all informations are correctly, confirm with
The programming information is stored in a TIMER block.
6 Insert a cassette with an intact security tab (unprotected).
7 Switch off with
The programmed recording will only function when the
video recorder is switched off with
If any of the TIMER blocks are in use, '
the video recorder display.
, then
on the remote control twice . A free
. The information will appear on the
VPS
REP. PROG. START PDC END
MO-FR 01 20:00 ] 21:30
STOREpOK
, P or Q you can select 'DATE'
;P+
on the remote control.
0-9
to select from the following options:
('E1') or
EXT.1 AV. 1 EXT.2 AV. 2
. Using
TIMER
STANDBY m .
STANDBY m
k
' will light up on
P- =
or ,
('E2').
.
OK
.