Hitachi 42PD4200 User Manual page 36

Selected characters
Audio Input
AV1
Selected characters
Audio Input
AV2
AV3
AV1
AV4
AV2
AV3
Scart Output
AV4
Scart Output
RGB1
RGB1
RGB2 (1st step)
RGB2 (1st step)
RGB2 (2nd step)
RGB2 (2nd step)
OTHER FEATURES
Automatic Store
Approximately 1 sec. after adjustment is completed, the adjustments will be recorded as shown in the table below.
Menu Display
Picture
Picture Mode
Contrast
Brightness
Colour
Sharpness
Hue
Colour Temperature
Contrast Mode
YNR
CNR
Film Mode
PAL Comb Filter
LTI
CTI
Black Enhancement
Auto Colour
Colour Temp. Adjust
R Amplitude For every Colour Temperature, 1
G Amplitude
B Amplitude
R Cut Off
G Cut Off
B Cut Off
Colour Management
Magenta 1 setting is registered.
36
Stereo L/Mono
Stereo L/Mono
TV Monitor
TV Monitor
DVI-PC DVI-STB
DVI-PC DVI-STB
RGB Component
RGB Component
Auto HDTV SDTV/DVD
Auto HDTV SDTV/DVD
Registration condition
1 setting is registered.
For every input function and every
Picture Mode, 1 setting is
registered.
setting is registered.
For every input function and every
Picture Mode, 1 setting is
registered.
Red
This should correspond to the audio signal from the equipment that is
connected to AV1 audio input terminal. If it is monaural audio, set this to
L/Mono.
This should correspond to the audio signal from the equipment that is
(Same to AV1)
connected to AV1 audio input terminal. If it is monaural audio, set this to
L/Mono.
TV:AV4 (Scart) output will be fixed as TV signal output.
Monitor:AV4 (Scart) output can view the image as on the main unit. But it is
(Same to AV1)
possible to monitor only the composite video signal from AV1, AV2, or AV3
input that is displayed on the screen at the time.
• If Descrambler is set to On, it will be fixed as TV automatically.
This should correspond to the signal mode of the signal from the
This should correspond to the signal mode of the signal from the
equipment that is connected to RGB1 DVI terminal.
equipment that is connected to RGB1 DVI terminal.
This should correspond to the signal mode of the signal from the
This should correspond to the signal mode of the signal from the
equipment that is connected to RGB2 D-sub terminal.
equipment that is connected to RGB2 D-sub terminal.
This step should be set only when [Component] is selected on the 1st
This step should be set only when [Component] is selected on the 1st
step.
step.
This should correspond to the signal mode of the signal from the
This should correspond to the signal mode of the signal from the
equipment that is connected to RGB2 D-sub terminal.
equipment that is connected to RGB2 D-sub terminal.
• Normally, set this to Auto. The signal mode of the input signal will be
• Normally, set this to Auto. The signal mode of the input signal will be
automatically recognized.
automatically recognized.
• If the input signal contains much noise or has a low level at Auto and the
• If the input signal contains much noise or has a low level at Auto and the
operation is found erratic, set this to match the input signal.
operation is found erratic, set this to match the input signal.
Menu Display
Picture Yellow 1 setting is registered.
Green
Cyan
Blue
Colour Decoding
Green
Colour For every input function and every
Function
Video Power Save
Default Zoom
Setup
System
Colour System
Video Input
Audio Input
RGB1
RGB2
• The previously recorded items will be lost.
Setup hint
Setup hint
Registration condition
-
Red For every Colour Temperature, 1
setting is registered.
Picture Mode, 1 setting is
Hue
registered.
1 setting is registered.
1 setting is registered.
1 setting is registered.
AV1
AV2
AV3
AV4
-
AV1 1 setting is registered.
AV2
AV4
-
AV1 1 setting is registered.
AV2
AV3
AV4