Related Manuals for Master Bilt TAF-27 ERC2
Summary of Contents for Master Bilt TAF-27 ERC2
- Page 1 Installation & Operations Manual Master-Bilt Products 908 Highway 15 North New Albany, MS 38652 Phone: (800) 684-8988 PN 228-90000 Rev 05-04-04 bhs...
-
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION………………………………….…………………………………………………………………… STORE CONDITIONS…………………………….……………….…..…………………………………………….. 4 WARNING LABELS AND SAFETY INSTRUCTIONS………..…..……………………………………………… 5 PRE-INSTALLATION INSTRUCTIONS………………………..…..………………………………….…………… 6 Inspection for ShippingDamage……………………………………………………………….…………… 6 INSTALLATION INSTRUCTIONS………………………………………………………………………………….. 6 General Instructions…………………………………………………………………………………………. 6 Electrical...……………………………………………………………………………………………………..6 Leg and Condensate Pan Installation…..…………………………………………………………………..7 ELECTRONIC REFRIGERATION CONTROL (ERC)………….…………………………………….……………8 FINAL CHECK LIST…………………………………………………………………………………….…………….12 SENSOR PROBE ………………………………………………………………………………….……………….13 SERVICE INSTRUCTIONS…………………………………………………………………………………………..14 MASTER-BILT PART NUMBERS…………………………………………………………………………………..15... -
Page 4: Store Conditions
INTRODUCTION Thank you for purchasing a Master-Bilt cabinet. This manual contains important instructions for installing, using and servicing a Master-Bilt TAF ERC2 case. A parts list is included in with this manual. Read all these documents carefully before installing or servicing your equipment. STORE CONDITIONS The Master-Bilt TAF ERC2 cases are designed to operate in the controlled environment of an air-conditioned store. -
Page 5: Warning Labels And Safety Instructions
WARNING LABELS AND SAFETY INSTRUCTIONS This symbol is the safety-alert symbol. When you see this symbol on your cabinet or in this manual, be alert to the potential for personal injury or damage to your equipment. Be sure you understand all safety messages and always follow recommended precautions and safe operating practices. -
Page 6: Pre-Installation Instructions
PRE-INSTALLATION INSTRUCTIONS INSPECTION FOR SHIPPING DAMAGE You are responsible for filing all freight claims with the delivering truck line. Inspect all cartons and crates for damage as soon as they arrive. If damage is noted to shipping crates or cartons or if a shortage is found, note this on the bill of lading (all copies) prior to signing. -
Page 7: Electrical
3. Rotate your stock so that older stock does not accumulate. This is especially important for ice cream. A "First-In, First-Out" rotation practice will keep the products in good salable condition. 4. Do not place product in the case when it is soft or partially thawed. Also, product should not be put in the case for at least 6 hours after it is started. -
Page 8: Electronic Refrigeration Control (Erc)
CONDENSATE PAN INSTALLATION FOR TOP MOUNT CABINETS ONLY 1. Before moving cabinet into place, remove the condensate pan from the top unit compartment. Using the two screws supplied with the pan, attach the pan to the back of the cabinet at the two holes near the bottom of the plastic drain line. - Page 9 To initiate a Manual Defrost, press and hold the MAN DEF key for 3 seconds. There are two levels of programming in the ERC 2. The first level of security will enable the user to set two parameters: Time-of-day (CLoC) and Set point temperature (SEt). The other level allows access to the other parameters.
- Page 10 To change the other parameters (Second Level) follow these steps: Step 1 Press and hold SET and DOWN for 10 seconds. The display will show dSPL Step 2 Press SET to change the parameter Step 3 Press UP or DOWN to change the options, time or temperature for the current parameter Step 4 Press SET to accept the new value...
- Page 11 Minimum Minimum time that Range: from 0 to 15 min 2 min. Compressor the compressor On Time remain turned on Alarm Delay ALrd Time delay before Range: from 0 to 59 min 30 – for LT the alarm goes off 45 –...
- Page 12 High ALHi High temperature Range: from – 40 to 83°F or –40 to 50° F setpoint that will Temperature 23°C make the alarm go Alarm off and the error message appear on the display Important Note: To change from degrees C to F or vice-versa, the user must reprogram all the parameters that are related to the temperature.
-
Page 13: Final Check List
FINAL CHECK LIST Check operating pressures. Check electrical requirements of unit to supply voltage. Set temperature control for desired temperature range. Check system for proper defrost settings and operation. Check condensing unit for vibrating or rubbing tubing. Dampen and clamp as required. All valves should be completely open counter-clockwise. -
Page 14: Service Instructions
SERVICE INSTRUCTIONS (Trouble Shooting Guide) High head pressure and high back pressure: Condenser coil clogged or restricted. Condenser fan motor defective. Low back pressure and low head pressure: Restriction in system. Refrigerant undercharged. Leak in system. Pressures normal – cabinet warm: Coil blocked with frost or ice (see #4). -
Page 15: Master-Bilt Part Numbers
MASTER-BILT PART NUMBERS The table below gives Master-Bilt part numbers. Use this chart when ordering replacement parts for your TAF ERC2 cases. Description TAF-27 TAF-48 TAF-74 Bulb 23-00343 23-00343 23-00343 Bulb Holder 23-01080 23-01080 23-01080 Bulb Shield 23-01465 23-01465 23-01465 Caster W \ Brake 27-00591 27-00591... -
Page 16: Sale And Disposal
SALE AND DISPOSAL OWNER RESPONSIBILITY If you sell or give away your Master-Bilt cabinet you must make sure that all safety labels and the Installation - Service Manual are included with it. If you need replacement labels or manuals, Master-Bilt will provide them free.