Campbell Hausfeld DG460300CK Operating Instructions And Parts Manual page 2

Operating Instructions and Parts Manual
General Safety shock. If an extension cord must be
used, make sure:
Information
(Cont'd.) • That the pins on plug of extension
cord are the same number, size
8. Use steady, even pressure when
and shape as those of plug.
using tool. Do not force. Too much
• That the extension cord is
pressure can cause blade to break
properly wired and in good
or overheat.
electrical condition.
9. Keep all nuts, bolts and screws tight
and ensure equipment is in safe • If an extension cord is to be used
outdoors it must be marked
working condition.
with the suffix "W-A" or "W"
10. Do not put hands near or under
following the cord type
moving parts.
designation to indicate it is
WORK AREA acceptable for outdoor use.
For example – SJTW-A
Do not operate a
WARNING
!
3. Do not expose to rain, snow or
power tool in an
frost.
explosive atmosphere, such as in the
presence of flammable liquids, gases, or
PERSONAL SAFETY
dust. Power tools create sparks which
may ignite the fumes or dust.
WARNING
!
Keep work area
CAUTION
!
clean and well exposure to vibration, work in
lighted. Cluttered benches and dark awkward positions, and repetitive
areas invite accidents. work motions can cause injury to
hands and arms. Stop using any tool if
Keep bystanders,
CAUTION
discomfort, numbness, tingling, or pain
!
children, and
occur, and consult a physician.
visitors away while operating a power
1. Stay alert, watch what you are
tool. Distractions can cause you to lose
doing, and use common sense when
control.
operating a power tool. Do not use
tool while tired or under the
ELECTRICAL SAFETY
influence of drugs, alcohol, or
Double insulated tools are equipped with
medication. A moment of
a polarized plug (one plug blade is wider
inattention while operating power
that the other). This plug will fit in a
tools may result in serious personal
polarized outlet only one way. If the plug
injury.
does not fit fully into the outlet, turn the
plug over and insert into plug again.
CAUTION
!
Do not expose
WARNING switch is in the locked or off position
!
power tools to rain
before making any adjustments,
or wet conditions. Water entering a
changing accessories, or storing the
power tool will increase the risk of
tool. Carrying tools with your finger on
electric shock.
the switch with the switch on invites
accidents.
Avoid body contact
WARNING
!
with grounded
2. Remove adjusting keys or wrenches
surfaces such as pipes, radiators,
before turning on the tool. A key or
ranges, and refrigerators. There is an
wrench attached to a rotating part
increased risk of electric shock if your of the tool may result in personal
body is grounded.
injury.
3. Do not overreach. Keep
WARNING
!
Do not abuse cord. proper footing and
• Never carry tool by its cord. balance at all times.
• Never pull the cord to disconnect Proper footing and
from receptacle. balance enable better
control of the tool in unexpected
1. Make sure cord is located so that it
situations.
will not be stepped on, tripped
over, or otherwise subjected to 4. Always work in a well-
damage or stress. ventilated area. Wear an
OSHA-approved dust
2. Do not use an extension cord unless
mask and safety glasses.
absolutely necessary. Use of
improper extension cord could
result in a risk of fire and electric
www.chpower.com
5. Hold tool by insulated gripping
surface when performing an
operation where the tool may
contact hidden wiring. Contacting a
"live" wire will make exposed metal
parts of the tool "live" and shock
the operator.
6. Keep hands away from moving
parts.
7. Use clamps or another practical way
to secure the workpiece to a stable
platform. Never hold work in your
hand, lap, or against other parts of
your body when cutting.
8. Always use blades of the correct
size and shape mounting holes.
Blades that do not match the
mounting hardware of the saw will
increase risk of injury to the user
and damage to the tool.
Do not misuse this
product. Excessive
TOOL USE AND CARE
Do not use tool if
WARNING
!
switch does not
turn it on or off. Any tool that cannot
be controlled with the switch is
dangerous and must be repaired.
1. This tool must NOT be modified or
used for any application other than
that for which it was designed.
Do not force the
CAUTION
!
tool. Use the
correct tool for your application. The
correct tool will do the job better and
safer at the rate for which it is
designed.
2. Maintain tools with care. Keep
Avoid accidental
cutting tools sharp and clean.
starting. Be sure
Properly maintained tools with
sharp cutting edges are less likely
to bind and are easier to control.
3. Check for misalignment or binding
of moving parts, breakage of parts,
and any other condition that may
affect the tool's operation. If
damaged, have the tool serviced
before using. Many accidents are
caused by poorly maintained tools.
4. Use only accessories that are
recommended by the manufacturer
for your model. Accessories suitable
for one tool may create a risk of
injury when used on another tool.
5. Some wood contains preservatives
which can be toxic. Take extra care
to prevent inhalation and skin
contact when working with these
materials. Request and follow all
safety information available from
your material supplier.
2
Notes
Notes
Notas
DG460300CK
23