Subscribe to Our Youtube Channel
Related Manuals for C. Crane CC Radio 2
Summary of Contents for C. Crane CC Radio 2
-
Page 1: Instruction Manual
INSTRUCTION MANUAL PLEASE READ ALL THE INSTRUCTIONS COMPLETELY BEFORE USE AND SAVE THIS MANUAL FOR FUTURE REFERENCE Ver. 1.4... - Page 2 About the CCRadio 2 ccradio.com ccradio.com/faqs/ccradio2 ccrane.com...
- Page 4 Before Use...
-
Page 5: Button Identification
Button Identification Note: To deactivate the Alarm and Timer functions, press and hold the but- ton until it beeps again and the symbol disappears from the display. CCRadio 2 Page 5... -
Page 6: Getting Started
Getting Started POWERING YOUR RADIO Before powering your radio be sure to read the Safety Instructions on pages 27 and 28. AC OPERATION Page 6 CCRadio 2... -
Page 7: Installing The Batteries
Getting Started INSTALLING THE BATTERIES 1) Position the radio face down on a soft surface to protect it. 2) Remove the battery compartment cover. 3) Insert the (4) “D” cell batteries into the compartment as indicated in the drawing below. Be sure the negative (-) end is against the spring. -
Page 8: Display Panel
Getting Started DISPLAY PANEL Page 8 CCRadio 2... -
Page 9: Setting The Clock
Getting Started SETTING THE CLOCK Please read this entire section carefully before you start. radio off must SETTING THE ALARM To set the type of alarm: Alarm Alarm To shut off the alarm function: To set the alarm time: Alarm CCRadio 2 Page 9... -
Page 10: Snooze Feature
Getting Started Notes on the Alarm To stop the alarm from going off every day, press and hold the Alarm Button until ALARM disappears from the display. SNOOZE FEATURE Alarm SLEEP TIMER FEATURE Page 10 CCRadio 2... -
Page 11: Radio Operation
Radio Operation TUNING Manual Tuning Scan Tuning Rotary Tuning Memory Tuning Note: CCRadio 2 Page 11... -
Page 12: Weather Alert System
Radio Operation WEATHER ALERT SYSTEM NOTE: Hazard warnings are not available in all areas. NOTE: Be aware that if you are not using AC power the WEATHER ALERT will completely drain your batteries. If your batteries are dead and AC power is off, the WX Alert Alarm will not work. Setting the Weather Alert Page 12 CCRadio 2... -
Page 13: Special Note
Radio Operation SPECIAL NOTE Turning Off the Weather Alert ALERT CCRadio 2 Page 13... -
Page 14: Setting The Squelch
Radio Operation 2-METER HAM (VHF) BAND (144 TO 148 MHZ) SETTING THE SQUELCH NOTE: Page 14 CCRadio 2... - Page 15 Radio Operation SEARCHING FOR A NEW ACTIVE FREQUENCY arrl.org CCRadio 2 Page 15...
-
Page 16: Display Light
Radio Operation DISPLAY LIGHT When the radio is plugged into AC power, the display light will always Display Light on AC Power be on unless you turn it off. The special green LED bulbs last about 100,000 hours and use very little electrical energy. The display light has three light levels. - Page 17 AUX IN Jack Timer Activation Switch LINE OUT Jack (See page 22 for details.)
- Page 18 TIMER TIMER...
- Page 19 Radio Operation 2: T OFF TIME ET THE TIMER TIMER 3: T ET THE REQUENCY TIMER You must Press the Timer/Set Button again to complete the setup. The timer will go ON and OFF at the same time and same station every day until you turn the timer off or reprogram it.
-
Page 20: Specifications
Specifications FREQUENCY COVERAGE WEATHER BAND ROTARY TUNING KNOB RESOLUTION POWER SOURCE POWER CONSUMPTION AUDIO ANTENNA DIMENSIONS WEIGHT Page 20 CCRadio 2... -
Page 21: Aux In Jack
Specifications 300 - 1000mV RMS (line level) input from external audio source. Do AUX IN JACK not overload. 300 - 1000mV RMS (line output) LINE OUT JACK Low impedance, transistor driven switch. Used for operation of external TIMER ACTIVATION SWITCH recording devices. -
Page 22: Recording Devices
Accessories RECORDING DEVICES VersaCorder Item #VC Patch Cords Item #VPC CC Witness Item #CWT AM ANTENNAS Twin Coil Ferrite ® AM Antenna Item #TCA Terk AM Antenna Item #TR1 FM ANTENNAS FM Reflect Antenna Item #FMW Page 22 CCRadio 2... -
Page 23: Troubleshooting Guide
Troubleshooting Guide The CCRadio 2 will not turn on and none of the buttons work: The Lock Switch, located on the right side of the radio between the tuning and the volume knobs, is in the up position. Push the switch down to release the lock and resume normal operation of the radio. - Page 24 Troubleshooting Guide Poor reception on FM, Ham (VHF), or Weather band: Battery Power Level Indicator doesn’t show full charge when using rechargeable batteries: Page 24 CCRadio 2...
-
Page 25: Radio Noise Troubleshooting
Radio Noise Troubleshooting AM RADIO NOISE PROBLEMS AND POSSIBLE SOLUTIONS www.ccrane.com/radionoise CCRadio 2 Page 25... - Page 26 AM Tuning & Listening Tips ccrane.com/radionoise SAFETY DIRECTIONS AND PRECAUTIONS FROM YOUR ANTENNA SUPPLIER SHOULD BE FOLLOWED TO PRE- VENT INJURY FROM LIGHTNING OR ANY ACCIDENT External Antenna Terminal for AM Ground Terminal http://www.nrcdxas.org Page 26 CCRadio 2...
-
Page 27: Safety Instructions
Safety Instructions READ BEFORE OPERATING EQUIPMENT SAVE THESE INSTRUCTIONS CCRadio 2 Page 27... - Page 28 Safety Instructions Page 28 CCRadio 2...
-
Page 29: P Ersonal S Tation L Og
P ERSONAL S TATION L OG Station Time City Frequency Date Call Letters Please feel free to copy this page. CCRadio 2 Page 29... - Page 30 2-METER HAM FREQUENCY L OG Time Frequency Location/Call Sign Date Please feel free to copy this page. Page 30 CCRadio 2...
- Page 31 About C. Crane Company Inc.
- Page 32 Model: CCRadio FCC ID: BYG 014 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS. 1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND 2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Need help?
Do you have a question about the CC Radio 2 and is the answer not in the manual?
Questions and answers
My cc2 radio won’t let me use the memory tuning. I tried the reset and that didn’t help
The memory tuning on the C. Crane CC Radio 2 may not work after a reset because the reset can clear previously stored stations. After a reset, you need to reprogram the memory by tuning to a station, pressing and holding the Memory Button until you hear a beep, and confirming the memory number appears on the display.
This answer is automatically generated