1. Manuals
  2. Brands
  3. Bulldog Security Manuals
  4. Car Alarm
  5. 1402
  6. Installation and owner's manual

Bulldog Security 1402 Installation And Owner's Manual

Keyless entry and alarm system
Hide thumbs Also See for 1402:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual
INSTALLATION GUIDE
KEYLESS ENTRY AND ALARM SYSTEM • MODEL 1402
CONTENTS
System Features .......................................
System Components .....................................
Required Tools ........................................
Technical Assistance ..................................
Before You Begin ......................................
Precautions...........................................
Testing Your Wires ....................................
Locating & Making Connections ........................ 4-7
Neutral Safety Switch ................................. 7
Connecting Wire Harness ............................... 8
Operator Programming Instructions ................... 9-12
Using Your Remote Transmitter ...................... 12-13
All tech personnel are expertly qualified to answer any technical questions.
Technicians are available Monday through Friday from 9:00 a.m. until 8:00 p.m. and Saturday 10:00 a.m. until 4:00 p.m.
OWNER'S GUIDE
Technical Assistance
Address
288 Canton Avenue • Wintersville, Ohio 43953
Telephone
Phone: 740-264-4710 • 800-878-8007 • Fax: 740-264-7306
•
1
1
1
2
2
2
2
3-4

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 1402 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Bulldog Security 1402

Summary of Contents for Bulldog Security 1402

  • Page 1: Table Of Contents

    INSTALLATION GUIDE • OWNER’S GUIDE KEYLESS ENTRY AND ALARM SYSTEM • MODEL 1402 CONTENTS System Features ........System Components ........Required Tools ........Technical Assistance ........Before You Begin ........Precautions........... Testing Your Wires ........Making Connections ........Locating & Making Connections ......4-7 Neutral Safety Switch .........

  • Page 2: System Features

    SYSTEM FEATURES 2 Four-Button Extended Control your car from an extended distance. Range Remote Control Keyless Entry Remotely locks and unlocks your power door locks. Remote Locking and Remotely locks your power door locks when the ignition is turned on and Unlocking with Ignition unlocks your power door locks when the ignition is turned off.

  • Page 3: Technical Assistance

    It is computer controlled and manufactured in the U.S.A. The dependability and variety of features make Bulldog Security the leader in the industry. Enjoy your new system for years to come! Since there are many different makes and models of vehicles, look at the wiring chart on our website, www.bulldogsecurity.com/wires.htm.

  • Page 4: Making Wiring Connections

    MAKING WIRING CONNECTIONS 1. Strip back two inches of insulation on the wire from the keyless entry. Two Inches of Bare Wire 2. Strip back one inch of insulation on the wire you need to connect to. One Inch of Bare Wire 3.

  • Page 5: Locating & Making Connections

    2. Twist upper wires together, twist lower wires together as shown. 3. Lay upper twisted pair of wires over right wire as shown. Bring lower twisted pair of wires up to meet the left wire as shown. 4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection. Secure with wire ties as shown.
  • Page 6 CONNECTING THE POWER AND GROUND 1. Connect the RED wire from the harness to a constant 12 volt supply or to the wire you ran from the positive battery post (if no constant 12 volt supply was found at the ignition switch harness). 2.
  • Page 7 Connect the control module ORANGE wire negative (-) out when armed to the optional starter disable relay (-) negative input. Pin 86 on SPDT 30 amp relay or use part #PRO1010 and relay #30-ARB To connect “Key Side” and “Starter Side” of the cranking wire to the optional relay for Starter Disable.

  • Page 8: Neutral Safety Switch

    the system. TO RED WIRE ON SIREN •To prevent water damage, the siren should NOT be mounted in a wheel well, directly behind the radiator grill or close to the ground. •Mount the siren as far away from sources of heat, i.e. exhaust manifold, turbo charger, etc.

  • Page 9: Connecting Wire Harness

    CONNECTING WIRING HARNESS L.E.D. (BLUE) (+) 12 Volt Constant BLACK Chassis Ground BROWN (+) Parking Light Output ORANGE* (-) Output when armed; starter disable, etc. YELLOW (+) 12 Volt Ignition Sense Input Ignition Harness (or) Fuse Box BLUE* (+) Lock or (-) Unlock Output 200ma Max GRAY* (-) Output to Horn Relay 200ma Max (or)

  • Page 10: Operator Programming Instructions

    OPERATOR PROGRAMMING INSTRUCTIONS ENTERING PROGRAMMING MODE Make sure your vehicle is not running and the brake is pressed. The brake is to remain pressed as long as you want to remain in programming mode. The only exception is when a different remote has been learned. The unit will exit the programming mode simply by releasing the brake and the parking lights will flash three (3) times.
  • Page 11 A. Turn the ignition switch to the on or run position. B. Press and hold button #1 on the transmitter for approximately 10 seconds or until parking lights flash once. C. Press and release button #2 on the transmitter. The parking lights will flash twice and the LED begins to flash.
  • Page 12 PROGRAMMING TABLES TO ENTER OPERATING PROGRAMMING MODE A. Turn the ignition switch to the on or run position. B. Press and hold transmitter button #1 for approximately 10 seconds or until the parking lights flash once. C. Press one of the following buttons to go to the following tables: BUTTON FLASHES SETTING...

  • Page 13: Using Your Remote Transmitter

    3.5 sec. Door Lock Pulse Length Negative Input Activated Negative Input Deactivated Siren Tone Output Car Horn Output Positive Door Pin Input Negative Door Pin Input TABLE FIVE BUTTON FLASHES SETTING Delayed Dome Lights Activated Delayed Dome Lights Deactivated TO EXIT PROGRAMMING MODE Turn the ignition switch to the off position.
  • Page 14 This feature is useful when having your vehicle valet parked, washed or serviced. While in valet mode, keyless entry and instant panic will still work; however, the alarm will not arm. Valet mode may also be programmed while the engine is running. Arming Press transmitter button #1 to arm the system.

Table of Contents