Subscribe to Our Youtube Channel
Related Manuals for Bulldog Security 1402
Summary of Contents for Bulldog Security 1402
- Page 1 All manuals and user guides at all-guides.com INSTALLATION GUIDE • OWNER'S GUIDE Keyless Entry 1-800-659-0764 and Alarm System Model 1402 BULLDOG SECURITY Creating A Higher Standard...
- Page 2 All manuals and user guides at all-guides.com 2 Four-Button Extended Range Remote Control Keyless Entry Remote Locking and Unlocking with Ignition Switch NOTE: This feature can also be used while the unit is wired as an alarm. Remote Valet Remote Full Time Silent Arming Remotely Programmable...
- Page 3 All manuals and user guides at all-guides.com On-Board Parking Light Relay On-Board Door Lock Relay Plug In Six Function LED Status Indicator E Square Memory Backup Code Learning Should you need help. First check our website at www.bulldogsecurity.com or call our toll-free Tech Support Hotline Monday through Friday 9AM-8PM and Saturday 10AM- 4PM EST at 800-878-8007.
- Page 4 All manuals and user guides at all-guides.com DO NOT wiring chart www.bulldogsecurity.com/wires.htm NOTE:If it is necessary to cut a factory wire to make a connection, see diagram on page 8. DO NOT such as crimp or snap together taps DO NOT DO NOT DO NOT MOUNT THE MODULE UNDER THE DASH...
-
Page 5: Follow These Instructions
All manuals and user guides at all-guides.com CAUTION: All wires must be wrapped with tape and wire tied. MAKING END TO END CONNECTIONS FOLLOW THESE INSTRUCTIONS CONSTANT POWER (+12V, key in any position including off) - Page 6 All manuals and user guides at all-guides.com CONNECTING THE NEGATIVE OUTPUT #1, BUTTON #2 BLUE NOTE: A SPST or SPDT relay must be used if you want to convert the negative signal to positive CONNECTING THE POWER AND GROUND or if the device you’re controlling draws more than 200 ma.
-
Page 7: Connecting The Starter Disable
All manuals and user guides at all-guides.com DETERMINING YOUR VEHICLE’S DOOR PIN SWITCH TYPE CONNECTING THE MAIN WIRING HARNESS TO THE MODULE NOTE: For your alarm system’s arming feature to work, you must DO NOT plug the harnesses into the control module until all connections have connect the alarm to the door pin switch. - Page 8 All manuals and user guides at all-guides.com CONNECTING THE CAR HORN WIRE YELLOW To (-) horn wire in vehicle Back of #775 (relay and harness) BLACK/BLUE WHITE BLACK To (+) horn honk output wire from unit BLUE Not used BLACK/BLUE MOUNTING AND CONNECTING THE OPTIONAL SIREN MOUNTING AND CONNECTING THE...
-
Page 9: Connecting The Dome Light Supervision
All manuals and user guides at all-guides.com BLACK NOTE: This unit is designed to use only a single stage sensor. If you are using a dual stage sensor, use only the major output of the sensor. CAUTION: When adding more than one perimeter sensor on the same input trip, you must add a 500ma diode to the output of each sensor. - Page 10 All manuals and user guides at all-guides.com “Type A” “Type A” (+) Positive (5-pin harness) NOTE: BLUE/BLACK BLUE/WHITE “Type B” Door Lock Test (Most Imports, some newer Fords) RED/BLACK +12V Constant “Type B” GREEN/BLACK GREEN/WHITE “Type C” Door Lock Test (Most Fords, some Chryslers, GM Trucks) NOTE: RED WITH BLACK STRIPE +12V constant power.
-
Page 11: Silent Arming/Disarming
All manuals and user guides at all-guides.com “Type C” Reverse Polarity (5-pin harness) KEYLESS ENTRY BLUE/BLACK FUNCTIONS LOCKING DOORS BLUE/WHITE RED/BLACK BULLDOG +12V Constant GREEN/BLACK UNLOCKING DOORS GREEN/WHITE NOTE: RED WITH BLACK STRIPE +12V constant power NOTE: You will need to cut factory wiring to make an end LOCKING AND UNLOCKING WITH IGNITION SWITCH to end connection, see “Making Connections”... - Page 12 All manuals and user guides at all-guides.com PASSIVE ARMING VALET MODE LED STATUS INDICATOR OVERRIDE SWITCH SHOCK LOCK If passive arming without door locking is programmed, the doors will SHOCK SENSOR automatically lock when a shock violation occurs. They will remain locked until 60 seconds after the violation has ended.
- Page 13 All manuals and user guides at all-guides.com DUAL LOCK/UNLOCK PULSE CLEARING THE E-PROM MEMORY PROGRAMMING A NEW TRANISMITTER HORN/SIREN FUNCTIONALITY DOOR PIN POLARITY PROGRAMMING CLEARING THE E-PROM MEMORY KEEP THIS MANUAL IN YOUR GLOVEBOX TO USE AS A REFERENCE. KEEP THIS MANUAL IN YOUR GLOVEBOX TO USE AS A REFERENCE.
- Page 14 All manuals and user guides at all-guides.com Here's how your warranty works: Creating A Higher Standard DISCLAIMER LIMITATION OF REMEDIES JBS Technologies, LLC...
Need help?
Do you have a question about the 1402 and is the answer not in the manual?
Questions and answers