Changing The Settings; About The Auto Standby Function; About The Talk Over Function; Setting Preferences - Pioneer DJM-850-K Operating Instructions Manual

Changing the settings

1 Press the [MIDI] [SETUP (WAKE UP)] button for at
least 1 second.
The [USER SETUP] screen is displayed.
! To display the [CLUB SETUP] screen, first turn the unit's power off,
then press the [POWER] button while pressing the [MIDI] [SETUP
(WAKE UP)] button.
2 Press the [BEAT c, d] button.
Select the setting item.
3 Press the [TAP] button.
The screen switches to the setting item's setting value change screen.
4 Press the [BEAT c, d] button.
Change the setting value.
5 Press the [TAP] button.
Enter the setting value.
The previous screen reappears.
! To return to the previous screen without changing the settings, press
the [AUTO/TAP] button.
6 Press the [SETUP (WAKE UP)] button.
Close the [USER SETUP] screen.
! To close the [CLUB SETUP] screen, press the [POWER] button to turn
this unit's power off.

Setting preferences

*: Setting upon purchase
Options
Mode
settings
Fader Start
MIDI CH
USER SETUP MIDI Button Type MIDI BT
Talk Over Mode
Talk Over LEVEL
Digital Master
Out Level
Digital Master
Out Sampling
Rate
MASTER ATT.
CLUB SETUP
Auto Standby
Mic Output To
Booth Monitor
PC UTILITY
Factory Reset
1 Note that the output sound may be distorted even if the master level indicator does not light up to the very top.
24
En
Screen display Setting value
F.S.
ON*, OFF
MIDI CH 1* to 16
TGL*, TRG
TLK MOD ADV*, NOR
–6 dB, –12 dB,
TLK LVL
–18 dB*, –24 dB
–19 dB*, –15 dB,
DOUT LV
–10 dB, –5 dB
DOUT FS 48 kHz, 96 kHz*
–6 dB, –3 dB,
MST ATT
0 dB*
AUTOSTB ON*, OFF
MIC BTH ON*, OFF
PC UTLY ON*, OFF
INITIAL YES, NO*

About the auto standby function

When [Auto Standby] is set to [ON], the standby mode is set automati-
cally if 4 hours pass with all of the conditions shown below met.
— That none of this unit's buttons or controls are operated.
— That no audio signals of –10 dB or greater are input to this unit's
input terminals.
! When the [SETUP (WAKE UP)] button is pressed, the standby mode
is canceled.
! This unit is shipped with the auto standby function turned on. If you
do not want to use the auto standby function, set [Auto Standby] to
[OFF].

About the talk over function

The talk over function has the two modes described below.
— [ADV] (advanced talk over): The mid-range only of the sound of chan-
nels other than the [MIC] channel is attenuated according to the
[Talk Over LEVEL] setting value and output.
dB
— [NOR] (normal talk over): The sound of channels other than the [MIC]
channel is attenuated according to the [Talk Over LEVEL] setting
value and output.
dB
Descriptions
Turns the fader start function on and off for all DJ players connected to the [CONTROL]
terminals.
Sets the MIDI channel.
Selects the MIDI signal transmission mode, [TGL (TOGGLE)] or [TRG (TRIGGER)].
Selects the talk over function's mode, [ADV(ADVANCED)] or [NOR(NORMAL)].
Sets the talk over function's sound attenuation level.
Sets the maximum level of the sound output from the [DIGITAL MASTER OUT] terminals.
Sets the digital signal's sampling rate.
Sets the attenuation level of the sound output from the [MASTER1] and [MASTER2]
terminals.
Turns the auto standby function on and off.
Sets whether or not to output the microphone's audio signals from [BOOTH] terminals.
Sets whether or not to launch the computer's setting utility software automatically when
a USB cable is connected.
Restores all the settings to their factory defaults.
Frequency
Frequency
1