Pioneer DJM-850-K Operating Instructions Manual page 23

Category
EFFECT
SELECT
BEAT EFFECTS
CH SELECT
TIME
LEVEL/DEPTH
ON/OFF
! When an effect other
than [SND/RTN] is
selected at BEAT
EFFECT
ON/OFF
! When [SND/RTN]
is selected at BEAT
EFFECT
HI
MIC
LOW
NOISE
GATE
SOUND COLOR FX
CRUSH
FILTER
FADER START 1
FADER START 2
Fader Start
FADER START 3
FADER START 4
MIXING
HEADPHONES
LEVEL
Timing Clock
FADER START 1
FADER START 2
Fader Start
FADER START 3
FADER START 4
START
MIDI
STOP
1 When turning one button on switches another button from on to off, MIDI on and off messages are sent from the two buttons.
When there is no button that switches off, only the MIDI on message is sent from the button that was pressed.
2 When switched from one position to another position, the MIDI ON and OFF signals are sent respectively from both positions.
! When the [START/STOP] button is pressed for over 1 second, MIDI messages corresponding to the positions of the buttons, faders and controls are sent in a bundle
(Snapshot).
The MIDI Snapshot sends all MIDI messages other than MIDI start and MIDI stop.
SW Name SW Type
Switch
DELAY
ECHO Switch
Switch
UP ECHO
SPIRAL Switch
REVERB Switch
TRANS Switch
FILTER Switch
FLANGER Switch
PHASER Switch
ROBOT Switch
SLIP ROLL Switch
Switch
ROLL
REV ROLL Switch
Switch
SND/RTN
CH1 Switch
Switch
CH2
CH3 Switch
CH4 Switch
MIC Switch
CF.A Switch
CF.B Switch
MASTER Switch
Switch
Switch
Switch
Button
Button
Control
Control
Button
Button
Button
Button
Button
Button
Button
Button
Control
Control
—
Button
Button
MIDI assignment Trigger/Toggle
CC 042
2
CC 055
2
CC 061
2
CC 043
2
CC 054
2
CC 053
2
CC 059
2
CC 050
2
CC 057
2
CC 051
2
CC 058
2
CC 046
2
CC 047
2
CC 062
2
CC 034
2
CC 035
2
CC 036
2
CC 037
2
CC 038
2
CC 039
2
CC 040
2
CC 041
2
CC 013 —
CC 045 —
CC 091 —
CC 114 —
CC 064 —
CC 030 —
CC 031 —
CC 085 Trigger/Toggle
CC 105 Trigger/Toggle
CC 086 Trigger/Toggle
CC 087 Trigger/Toggle
CC 088 Trigger/Toggle
CC 089 Trigger/Toggle
CC 090 Trigger/Toggle
CC 093 Trigger/Toggle
CC 027 —
CC 026 —
Timing Clock —
Note 102 —
Note 103 —
Note 104 —
Note 105 —
START —
STOP —
Transmitted data
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
—
TIME value (When FLANGER,
PHASER or FILTER is selected, the
value is halved. When a negative
value is selected, it is set to a posi-
tive value.)
0-127
OFF=0, ON=127
OFF=0, ON=127
0-127
0-127
1
OFF=0, ON=127
1
OFF=0, ON=127
1
OFF=0, ON=127
1
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
0-127
0-127
—
BACK CUE = 0, PLAY = 127
BACK CUE = 0, PLAY = 127
BACK CUE = 0, PLAY = 127
BACK CUE = 0, PLAY = 127
—
—
23
En