Earn BISSELL Rewards! Earn BISSELL Rewards! egister your egister your product today! product today! See details on See details on back page back page USER'S GUIDE 30C7 SERIES Thank You Safety Instructions Product View Assembly Operations Maintenance and Care 10-15...
Page 2
Your BISSELL OptiClean vacuum is well made, and we back it with a limited three year warranty. We also stand behind it with a knowl- edgeable, dedicated Consumer Services department, so, should you ever have a problem, you’ll receive fast, considerate assistance.
MPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic Keep hair, loose clothing, fingers, and all ■ precautions should be observed, including parts of body away from openings and the following: moving parts. Read all Turn off all controls before plugging or ■...
ssembly caution: the only tool you’ll need to assemble your vacuum cleaner is a phillips head Do not plug in your vacuum screwdriver. cleaner until you are familiar attach handle to vacuum with all instructions and operating procedures. 1. Locate the bag that contains the extension wand support, lower cord wrap, and screws.
ssembly attach storage clips, tool, and vacuum hose continued 5. Make sure that crevice tool is inside the extension wand. Store the extension wand and crevice tool on the back of the unit. Place tools on the extension wand support TurboBrush ®...
perations brush switch Brush Switch the rotating brush is turned on or off using the switch located next to the power switch on the top of the tank. When the brush switch is on, the brush will start rotating when the unit is reclined.
perations using the tools attach desired tool to hose for above floor cleaning surfaces or hard to reach areas. 1. Remove Hose: With vacuum in upright posi- tion, remove hose end from the suction inlet near the bottom of the vacuum by the wheel. Do not remove “tabbed”...
Page 9
perations empty dirty container empty the dirt container as soon as the dirt reaches the “full” line on the side of the container. 1. Unplug the vacuum from electrical outlet. 2. Slide the Lock 'n Seal Lever to the “unlock” position. 3.
aintenance and care cleaning the pre-motor filter WaRning: the pre-motor filter should be Do not operate cleaner checked often and washed as with damp or wet filters needed to maintain performance. or without all filters in More or less frequent cleaning may place.
aintenance and care clearing clogs low suction or poor pickup may be caution: due to a clog in the vacuum cleaner. To reduce the risk of if you notice a change in the sound injury from moving parts, of the motor or a reduction in the turn off vacuum cleaner spinning action in the dirt container, and disconnect power...
If the cleaner will not turn on or the thermal protector continues to activate, your cleaner may need servicing. Call BISSELL Consumer Services or visit the website to locate an authorized Service Center. note: the thermal protector controls the main vacuum motor only, not the brush motor.
aintenance and care check rotating floor brush and drive belt you should check your vacuum cleaner’s rotating floor brush and drive belt regularly for wear and damage. you should also clean the brush and brush ends of strings, hair, and carpet fibers. this type of debris can wrap around the brush and hamper its ability to effectively clean your carpet.
3. Place one end of the new drive belt over motor pulley and the other end over the brush in the space between the bristles. note: it is important that you use only genuine bissell replacement parts. generic belts may not meet the exact specifications required to keep your vacuum operating at its peak performance.
Page 15
aintenance and care turbobrush tool maintenance the turbobrush tool should be checked regularly for clogs or debris wrapping around the brush. note: Model 30c7t comes with the pet turbobrush tool and follows same maintenance instructions. 1. Remove tool from hose or from vacuum. 2.
roubleshooting WaRning: To reduce the risk of electric shock, turn power OFF and disconnect polarized plug from Vacuum cleaner won’t turn on electrical outlet before performing maintenance or troubleshooting. possible causes Remedies Power cord not plugged in 1. Check electrical plug Blown fuse/tripped breaker in home 2.
203-1512 Foot Brush Roll 203-1509 Pre-Motor Foam Filter 203-1510 Post-Motor Filter dditional accessories these items are available for purchase as accessories for your bissell opticlean: to purchase call 1-800-237-7691 or visit www.bissell.com. Item Part No. Part Name 203-1056 Crevice Tool...
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL Homecare, Inc. will repair or replace (with new or remanufactured components or products), at BISSELL’s option, free of charge from the date of purchase by the original purchaser, for three years any defective or malfunctioning part.
Page 20
Grand Rapids MI 49501 ATTN: Consumer Services Or visit the BISSELL website - www.bissell.com When contacting BISSELL, have model number of cleaner available. Please record your Model Number: ___________________ Please record your Purchase Date: ___________________ note: please keep your original sales receipt. it provides proof of purchase date in the event of a warranty claim.