Remote Control; General - Dynex DX-24L230A12 User Manual

Troubleshooting
Problem Solution
The picture has a • A few bright or dark spots on an LCD
few bright or dark screen is normal. It does not affect the
spots. operation of this TV.
Good picture, but no • Increase the volume.
sound. • Make sure that the sound is not muted.
• Make sure that the correct audio mode
is selected.
• Make sure that the audio cables are
connected correctly and securely to
the back of your TV.
• Make sure that the antenna or cable TV
is connected correctly and securely.
See "Connecting a cable or satellite
box" on page 9 or "Connecting an
antenna or cable TV (no box)" on
page 12.
• If you are using an antenna, the digital
channel signal may be low. To check
the digital channel signal strength, see
"Checking the digital signal strength"
on page 25.
• The audio cable(s) you are using may
be bad. Try a new set.
Poor picture • Make sure that the room is not too
bright. Light reflecting off the screen
can make the picture difficult to see.
• If an S-VHS camera or a camcorder is
connected while another connected
device is turned on, the picture may be
poor. Turn off one or more devices.
Good sound but • Adjust the contrast, color, and
poor color brightness settings.
Audio noise • Other devices (for example, surround
sound receiver, external speakers, fans,
or hair dryers) may be interfering with
your TV. Try turning off one device at a
time to determine which device is
causing interference. Once you have
determined which device is causing
interference, move it further from the
TV to eliminate the interference.
No output from one • Adjust the audio balance. See
of the speakers "Adjusting sound settings" on page 22.
• Make sure that the audio cables are
connected correctly and securely to
the back of your TV.
After images appear • Do not display a still image, such as a
logo, game, or computer image, for an
extended period of time. This can
cause a permanent after-image to be
burned into the screen. This type of
damage is not covered by your
warranty.
DX-24L230A12/DX-32L220A12/DX-46L261A12

Remote control

Problem Solution
Remote control • Make sure that the power cord is
does not work. correctly connected to your TV and a
power outlet.
• Make sure that there are no
obstructions between the remote
control and the remote control sensor
on the front of the TV.
• Point the remote control directly at the
remote control sensor on your TV. For
the location of the remote control
sensor, see "Front" on page 5.
• Make sure that the batteries are
installed correctly. See "Installing
remote control batteries" on page 17.
• Replace dead batteries with new
batteries. See "Installing remote
control batteries" on page 17.
Trouble • See instructions and a table of
programming your common codes in "Programming a
existing universal different universal remote control" on
remote control. page 40.
• Codes are subject to change. For up to
date codes, go to
www.Dynexproducts.com.
• Replace dead batteries with new
batteries. See "Installing remote
control batteries" on page 17.
• Refer to the User Guide that
accompanied your universal remote
control and contact the manufacturer
if problems persist.

General

Problem Solution
No power • Make sure that the power cord is
correctly connected to your TV and a
power outlet.
• Unplug the power cord, wait 60 seconds,
then plug the cord back in and turn on
your TV.
• Other devices (for example, surround
sound receiver, external speakers, fans, or
hair dryers) may be interfering with your
TV. Try turning off one device at a time to
determine which device is causing
interference. Once you have determined
which device is causing interference,
move it further from the TV to eliminate
the interference.
"No signal" error • Press INPUT and make sure that you have
message is selected the correct input for the device
displayed or service you are trying to use.
• If you are using a cable or satellite box,
use the remote that came with that box
to change channels.
After Auto • Reception can vary by channel
Channel Search, depending on the broadcast power level
there are no of a given station. Contact your cable or
channels satellite TV provider.
• Make sure the antenna or cable/satellite
TV is connected securely to your TV.
• Try replacing the cable between the
antenna/cable or cable/satellite box and
your TV.
37