Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for elysia museq
Summary of Contents for elysia museq
- Page 2 GmbH. Other product and brand names contained in this document are used for identification purpos- es only.
- Page 3 To avoid damaging the unit, please allow it to reach room temperature before switching it on. CE Conformity elysia GmbH, Ringstraße 82, 41334 Nettetal, Germany, declares with sole respon- sibility that this product complies with the following norms and directives: •...
- Page 4 – as far as our experience goes – the special elysia features like high and low pass filters with additional resonance peak as well as the integrated warm circuit are unique in the market.
-
Page 5: Table Of Contents
BASICS Controls............6 Connectors. -
Page 6: Basics
BASICS Controls Both channels of the museq are absolutely identical regarding their electronic design. Therefore both sides of the front panel have exactly the same controls and switches. Every potentiometer offers 23 steps for a comfortable recall with an ample choice of values. Bottom Middle High... - Page 7 Low Cut (Low Band): switches the filter characteristics from Low Shelf to Low Cut with ad- ditional resonance peak (p. 11) Cut Gain (Low Band): switches the corresponding gain controller from boost to cut mode. This is only relevant for Low Shelf, but not for Low Cut mode. (p. 10) Narrow Q (Bottom Band): switches the quality factor (Q) of the corresponding frequency band from low (wide curve) to high (narrow curve).
-
Page 8: Connectors
@ 220 - 240 VAC 1.5 A Slo-Blo @ 110 - 120 VAC elysia GmbH • D-41334 Nettetal • Germany Mains module This module combines the line cord connector, the on/off switch, the fuse holder with in- tegrated 230/115 VAC voltage selector and a line filter for providing the transformer with clean current. -
Page 9: Level Issues
Level Issues Low Level This problem can eventually be caused by balanced wiring. If the level becomes low when the museq is activated, a pin of the XLR connector at the input is probably not connected. To ensure proper operation, make sure to have both pins connected. The classic example for this problem is a balanced XLR cable that is connected to an unbalanced output which only uses ground and pin 2 –... -
Page 10: Reference
REFERENCE Bottom Middle High Bottom Middle High Left Warm Warm Right Low Shelf Left: miscellaneous settings of the gain controller in boost (red) and cut mode (green) Right: miscellaneous settings of the frequency controller in boost mode Low Shelf Gain Low Shelf Frequency 100 200 50k 100k... -
Page 11: Low Cut
Bottom Middle High Bottom Middle High Left Warm Warm Right Low Cut/High Cut Left: miscellaneous settings of the gain controller at the same frequency in low cut mode Right: miscellaneous settings of the gain controller at the same frequency in high cut mode Low Cut Gain High Cut Gain 100k... -
Page 12: Middle
REFERENCE Bottom Middle High Bottom Middle High Left Warm Warm Right Middle Left: miscellaneous settings of the gain controller with wide (green) and narrow Q (red) Right: miscellaneous settings of the frequency controller in boost mode with wide Q Middle Gain Middle Frequency 100 200 50k 100k... -
Page 13: Warm
Bottom Middle High Bottom Middle High Left Warm Warm Right Warm Left: distortion rate in % at different input levels in Warm mode Right: frequency response at different input levels in Warm mode Warm THD+N Warm Frequency Response 50k 100k Bottom Middle High... -
Page 14: Appendix
APPENDIX Technical Data Frequency response: <10 Hz - >200 kHz (-0.2 dB) Low Band (Shelf Filter): 9 - 200 Hz (+/-15 dB) Low Band (Cut Filter): 9 - 200 Hz Bottom Band (Peak Filter): 18 - 400 Hz (+/-15 dB) Quality factor (Q): 1.3 (wide) and 0.5 (narrow) Middle Band (Peak Filter):... -
Page 15: Warranty
You will receive a return authorization which enables you to send your product to the elysia factory where it will be repaired and then sent back to you. All returns to the factory must be in the original packaging, accompanied by the return authorization, and must be shipped via insured freight at the customer‘s own expense.