Memorizing The Service; Receiving The Memorized Service; Memorizing The Ensemble Automatically; Pty (Programme Type) Tuning - Alpine DVA-7996R Owner's Manual

DAB Operation
A.ME Preset buttons (1 through 6)
BAND
T.INFO
TITLE
DN UP

Memorizing the Service

1
Select the service that you want to memorize.
2
Press any one of the Preset buttons (1 through 6) for
at least 2 seconds while the "FUNC" indicator light
goes out. The selected service is memorized.
3
To memorize more, repeat the above steps 1 and 2.
NOTES
• You can memorize up to 18 stations (6 stations for each
band; DAB1, DAB2, DAB3).
• If you select a preset button that has already memorized a
service, the new selection takes it over.
• When you are not receiving DAB, the service is not
memorized. (Memorize the service when the DAB reception
is good.)

Receiving the Memorized Service

1
Press the BAND button to select your desired band.
2
Press one of the Preset buttons (1 through 6).
The selected service is received.
By selecting the mode in the "Changing the Display
Mode" section (see page 25), the display shows the
status of the broadcasting stations that have been
received as follows:
Channel No. Display: the channel numbers of received
stations are displayed.
Ensemble Label Display: the Ensemble Label of
received station is displayed.
Service Label Display: the Ensemble Label is displayed
for 2 seconds and then the Service Label is displayed
after receiving the broadcasting station.
Component Label Display: the Ensemble Label is
displayed for 2 seconds, then the Service Label is
displayed for 2 seconds, and then the display is
changed to the Component Label after receiving the
broadcasting station.
Dynamic Label Display: the Ensemble Label is
displayed for 2 seconds, then the Service Label is
displayed for 2 seconds, and then the display is
changed to the Dynamic Label after receiving the
broadcasting station.
24
-EN
F
PTY
NOTE
When you receive the Secondary Service Component, you
memorize the service, but when you call out this memorized
service, the Primary Service Component will be called out.

Memorizing the Ensemble Automatically

1
Press the BAND button to select the band that you
want to receive.
2
Press and hold the A.ME button for at least 2 seconds.
The ensemble is searched for, and six ensembles are
automatically received and memorized with the preset
buttons (1 through 6).
When memorization has completed, the Ensemble that
was memorized last is received.
By selecting the mode in the "Changing the Display
Mode" section (see page 25), the display shows the
status of the broadcasting stations that have been
received as follows:
Channel No. Display: the channel numbers of received
stations are displayed.
Ensemble Label Display: the Ensemble Label of
received station is displayed.
Service Label Display: the Ensemble Label is displayed
for 2 seconds and then the Service Label is displayed
after receiving the broadcasting station.
Component Label Display: the Ensemble Label is
displayed for 2 seconds, then the Service Label is
displayed for 2 seconds, and then the display is
changed to the Component Label after receiving the
broadcasting station.
Dynamic Label Display: the Ensemble Label is
displayed for 2 seconds, then the Service Label is
displayed for 2 seconds, and then the display is
changed to the Dynamic Label after receiving the
broadcasting station.
NOTE
If no ensemble is received, the one that has been received before
you perform this automatic memorization is received.

PTY (Programme Type) Tuning

1
Press the F button to turn on the "FUNC" indicator.
2
During radio (DAB receiving) mode, press the PTY
button to go to the PTY Select mode.
3
Press the DN or
desired programme type.
4
After selecting a programme type, and when the
"FUNC" indicator is turn on, press the PTY button to go
to the PTY Search mode.
The selected programme type is searched for.
NOTE
To cancel the PTY Search mode during the PTY search, press the
PTY button.
5
When the station is received, the received programme
type is displayed for 5 seconds. If no station is found,
"NO PTY" is displayed for 5 seconds.
NOTE
Above functions can be performed only for services within an
ensemble.
UP button to select your