Table of Contents
Advertisement
Quick Links
- To disassemble the control panel, unscrew the 3 internal screws
fixing the control panel to the oven face.
GREASING OF TAPS
If a tap becomes hard to be turned, grease it using a specific
grease withstanding high temperatures. Act as follows: open the
work-top and disassemble also the control panel as described on
the previous paragraph. Unscrew the two fixing screws from the
burner body (see picture) and remove the cone.
Fig. 50
Clean the cone and its slot by means of a cloth soaked with diluent.
Slightly grease the cone with the relevant grease, put it in its slot,
and turn it some times. Remove the cone again, remove the
exceeding grease making sure the gas entries are not obstructed
by grease residuals. Assemble everything carefully in the opposite
direction check the connection seal by means of soapy water.
TAPS REPLACEMENT
Act as follows: open the work-top and disassemble also the control
panel as described on the previous paragraph. Unscrew screw
nut D of the gas tube supplying the burner. Unscrew screw V fixing
the tap to the bridle and remove it (see picture).
Note: Every time the tap is replaced, it is necessary to replace
the seal gasket too check the connection seal by means of soapy
water.
D
V
7
Fig. 51
GAS OVEN WITH
WATT
GRILL HEATING ELEMENT
2000
CONVENTIONAL OVEN
WATT
UPPER ELEMENT
850
LOWER ELEMENT
1200
GRILL ELEMENT
850+1050
MULTIFUNCIONAL OVEN
WATT
UPPER ELEMENT
850
LOWER ELEMENT
1200
GRILL ELEMENT
850+1050
FANNED ELEMENT
2100
AIR FORCED OVEN
WATT
GRILL ELEMENT
2000
FANNED ELEMENT
2100
ELECTRIC PLATE
Ø mm
WATT
STANDARD
(A-C) 145
1000
RAPID
(D) 180
2000
STANDARD
(E) 180
1500
N.B.: the rapid electric plates are marked with a red dot.
E
C
A
D
Fig. 52
AREA FOR CERAMIC HOB
Ø mm
WATT
HALOGEN
(1-2) 200
1700
or RADIANT
1800
RADIANT
(4)
230
1700
or RADIANT
2100
RADIANT
(3)
165
1200
2
4
1
3
Fig. 53
INSTRUCTIONS
INSTRUCTIONS
BOOKLET
BOOKLET
mod.
GB
Advertisement
Table of Contents
Related Manuals for Baumatic BT2360SS
Summary of Contents for Baumatic BT2360SS
- Page 1 - To disassemble the control panel, unscrew the 3 internal screws GAS OVEN WITH WATT fixing the control panel to the oven face. GRILL HEATING ELEMENT 2000 GREASING OF TAPS If a tap becomes hard to be turned, grease it using a specific CONVENTIONAL OVEN WATT grease withstanding high temperatures.
-
Page 2: Appliance Maintenance
Make sure that the flame does not extinguish passing quickly from GENERAL INFORMATION RECCOMANDATIONS AND PRECAUTIONS the maximum flow to the minimum flow, and closing and opening DESTINED TO THE END USER the oven door (the oven door must be closed softly). Attention: for taps with safety device, the minimum adjusting screw ENVIRONMENT PROTECTION “T”... -
Page 3: Gas Adjustment
FIRST PART The hotplate is controlled by a commutator. Turn the knob until Fig. 36 bis GAS ADJUSTMENT position 1 to turn the hotlplate on. A warning light on the control Green & Yellow (Earth) panel will inform you if the plate is on or off. WORK-TOP USE If the appliance is foreseen to operate with a type of gas different Fuse... -
Page 4: Gas Connection
- by rigid pipe in iron or copper USE OF THE GAS OVEN ROOMS VENTILATION - by flexible tube in stainless steel with continuing wall, with mechanical connection in accordance with rules. The tube must be directly connected to the manifold elbow (see Use of the oven This appliance shall be installed in accordance with the regulations Fig. -
Page 5: Use Of The Electric Grill
SECOND PART OVEN DOOR To turn the oven light on, press switch For some models, the oven door can be disassembled in the INSTRUCTIONS DESTINED TO THE USER following way: hinges A are provided, for this purpose, with two movable jumpers Electric ignition of oven burner (optional) The oven door must always be completely open, before the B;... -
Page 6: Care And Maintenance
COOKING PROGRAMMER WITH SOUND SIGNAL HP33 – Thermostat knob combined to oven selector (optional) STANDARD (Fig. 24) USE OF THE ELECTRIC OVEN CARE AND MAINTENANCE NATURAL CONVECTION OVENS 1 - Clock (knob 2) The oven is fitted with: FIRST PART - Set the exact time of day by pulling and turning knob 2 Before cleaning the appliance, disconnect the gas general •... - Page 7 flashes. Setting Thermostat knob separate from oven selector To correct the setting error, change the cooking time and cooking After pressing a function button the time required can be set with end time. the +/- buttons. Medium grill The appliance must be used with closed oven door It is indicated for grilling and gratinating small quantities of traditional The counting-up and counting-down speed increases when the Cancelling a setting...
- Page 8 “LED” PROGRAMMER (Fig. 21) end time button the next cooking end time appears on the display. INSTRUCTIONS FOR USE OF CONTROL DEVICES PCI "Campanil"TR 259 Analogic (Fig.19) Set the cooking end time with + button. The relay and the cooking (ACCORDING TO THE MODELS) time symbol switch off.