Table of Contents
Advertisement
Available languages
Available languages
E
Speaker Connections
N
G
L
I
S
Caution:
Please follow the instructions given below. Failure to do so will cause damage to the unit and speakers.
H
12
<Right>
• Use ungrounded speaker only.
• The maximum speaker input should be 45 W or more. (If used with the optional
(White)
+
+
power amplifier, the speaker input should be higher than the maximum amplifier
L
-
-
(White
output.)
w/black stripe)
• The speaker impedance should be 4 - 8 .
(Gray)
• This unit uses the BTCL circuit, so each speaker should be connected separately
+
+
R
-
using parallel vinyl insulated cords.
-
(Gray
• The speaker cords and the power amplifier unit should be kept away (about 30 cm
w/black stripe)
apart) from the antenna and antenna extension cord.
<Wrong>
+
+
L
-
-
Chassis
+
+
R
-
-
Chassis
• Never connect the speaker cord to
• Do not use a 3-wire type speaker
the body of the car.
system having a common earth
lead.
Fuse
Use fuses of the same specified rating (15 A). Using different substitutes or fuses with higher ratings, or connecting the
unit directly without a fuse, could cause fire or damage to the unit.
If the fuse replacement fails, contact your nearest authorized Panasonic Service Center.
Product Servicing
If the suggestions in the charts do not solve the problem, we recommend that you take it to your nearest authorized
Panasonic Servicenter. The product should be serviced only by a qualified technician.
Maintenance
Your product is designed and manufactured to ensure the minimum of maintenance. Use a soft cloth for routine exteri-
or cleaning. Never use benzine, thinner, or other solvents.
18
CQ-RG153U
+
+
+
+
L
L
-
-
-
-
+
+
+
+
R
R
-
-
-
-
• Do not connect more than one
speaker to one set of speaker
leads.
Installation Guide
This installation information is designed for experienced installers and is not intended
for non-technical individuals. It does not contain warnings or cautions of potential dan-
gers involved in attempting to install this product.
Any attempt to install this product in a motor car by anyone other than qualified
installer could cause damage to the electrical system and could result in serious per-
sonal injury or death.
Installation Hardware
+
No.
Item
-
q
Mounting collar
+
-
w
Hex. nut (5 mmø)
e
Rear support strap
Tapping screw
r
(5 mmø 16 mm)
t
Mounting bolt (5 mmø)
y
Power connector
u
Dismounting plate
i
Trim plate
Overview
This product should be installed by a professional.
However, if you plan to install this product yourself,
your first step is to decide where to install it. The
instructions in these pages will guide you through the
remaining steps:
(Please refer to the "WARNING" statement above.)
• Identify and label the car wires.
• Connect the car wires to the wires of the power con-
nector.
• Install the unit in the dashboard.
• Check the operation of the unit.
WARNING
If you encounter problems, please consult your nearest
professional installer.
Diagram
Q'ty
Caution: This unit operates with a 12 V DC nega-
1
tive ground auto battery system only. Do not
attempt to use it in any other system. Doing so
1
could cause serious damage.
1
Before you begin installation, look for the items which
are packed with your unit.
1
• Warranty Card...Fill this out promptly.
• Panasonic Servicenter List for Service Directory
1
...Keep for future reference in case the product
needs servicing.
• Installation Hardware...Needed for in-dash installa-
1
tion.
Required Tools
2
You'll need a screwdriver, a 1.5 V AA battery, and the
following:
1
12 V DC
Electrical tape
Test bulb
E
N
G
L
I
S
H
13
Side-cut
pliers
19
CQ-RG153U
Hide quick links:
Advertisement
Table of Contents
