Specifications; Speaker Connections; Reset Switch - Panasonic CQ-VX1300W Operating Instructions Manual

Maintenance
E
(continued)
N
G
L
I
S
H
37
CD IN
u
CD EJECT
CST EJECT
INTEGRATED CD/CASSETTE RECEIVER WITH
u
CST IN
RESET

Speaker Connections

Caution: Please follow the instructions given below. Failure to do so will cause damage to the unit and speakers.
<Right>
¡Use ungrounded speaker only.
(White)
+
+
L ¡The maximum speaker output should be 41 W or more. (If used with
-
-
(White
w/black stripe)
¡The speaker impedance should be 4 - 8 Ω.
(Gray)
+
+
¡This unit uses the BTCL circuit, so each speaker should be connected
R
-
-
(Gray
w/black stripe)
¡The speaker cords and the power amplifier unit should be kept away
<Wrong>
+
+
L
-
-
Chassis
+
+
R
-
-
Chassis
¡Never connect the speaker cord to ¡Do not use a 3-wire type speaker
the body of the car. system having a common earth
lead.
50
CQ-VX1300W

Reset Switch

Reset switch
Insert a hard, slender stick into the hole and push the switch.
The unit returns to the default state when the trouble is reset.
Remember, the data and settings stored in the memory are
G
deleted.
Important
Push the switch only when the unit fails to operate with any but-
tons.
If the unit fails to return to normal condition, contact the shop
where you purchased this product and ask for repairs.
the optional power amplifier, the speaker output should be higher than
the maximum amplifier output.)
separately using parallel vinyl insulated cords.
(about 30 cm apart) from the antenna and antenna extension cord.
+
+ +
L L
- -
-
+
+
+
R R
- -
-
¡Do not connect more than one
speaker to one set of speaker
leads.

Specifications

General
Power Supply
Current Consumption
Rated Output
Maximum Power Output
Suitable Speaker Impedance
Audio Input Impedance
Audio Input Voltage
Pre-out Output Voltage
Pre-out Output Impedance
Dimensions (W x H x D)
Weight
DSP
Number of Channels
Space mode
Equalizer Center Frequency
Variable Range of Equalizer
FM Stereo Radio
Frequency Range
Usable Sensitivity
Total harmonic distortion (mono)
Weighted S/N ratio (mono)
Frequency Response
Stereo Separation
Image response ratio
AM Radio
Frequency Range
Usable Sensitivity
Image response ratio
CD Player
Channel
Quantization
Frequency Response
Dynamic range
Wow and Flutter
Cassette Tape Player
Reproduction system
Tape Speed
Fast Forward Time
Rewind Time
Wow and Flutter
Signal/Noise Ratio
+
+
- -
Frequency Response
+
+
- -
Note : Specifications and the design are subject to modification without notice due to improvements in technology.
Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation.
"DOLBY" and the double-D symbol B are trademarks of Dolby Laboratories Licensing Corporation.
: 12 V DC (11 V - 16 V), test voltage 14.4 V, negative ground
: Less than 8.5 A (CD play mode)
: 16 W x 4 ch (1 kHz, 1%, 4 Ω)
: 41 W x 4 ch
: 4 Ω
: 10 kΩ (AUX IN)
: Max. 2 V (AUX IN)
: 1.8 V
: 600 Ω
: 178 x 100 x 160 mm
: 2.4 kg
: 2 input channels, 4 output channels
: 7 mode
: 80, 160, 320, 640, 1.6 k, 4 k, 10 k (Hz)
: –12 to +12 dB (13 steps)
: 87.50 - 108.00 MHz
: 12 dBf.
: 0.3 % (1 kHz)
: 70 dB
: 20 Hz – 15 kHz (± 3 dB)
: 42 dB (at 1 kHz)
: 75 dB
: 531 kHz - 1,602 kHz
: 27 dB/µV
: 65 dB
: 2 channels
: 16-bit linear
: 5 Hz - 20 kHz
: 90 dB (IHF, A)
: Below measurable limits
: 4-track, 2-program stereo
: 4.76 cm/sec
: 100 sec (C-60)
: 100 sec (C-60)
: 0.07 % (WRMS)
: Dolby B NR OFF 56 dB (IHF, A)
Dolby B NR ON 66 dB (IHF, A)
: 30 Hz - 18 kHz (normal tape)
30 Hz - 20 kHz (metal tape)
CQ-VX1300W
E
N
G
L
I
S
H
38 1
51