Table of Contents
Advertisement
B:
IMPORTANT INSTALLATION
WARNING!
WARNING:
AN UNBALANCED DOOR OR
ONE
THAT
STICKS
PREVENT
THE
SENSING
WORKING PROPERLY, CAUSING INJURY OR
DEATH.
ENSURE
BALANCED AND ELIMINATE ANY STICKING OR
BINDING
PRIOR
TO
OPERATOR.
A properly balanced door will open slowly from a
3/4 open position, close slowly from a 3/4 closed
position, and remain still at a 1/2 open position. If
the door is not properly balanced, HAVE A
QUALIFIED SERVICE PERSON MAKE REPAIRS
TO
CABLES,
SPRING
OTHER
DOOR
INSTALLING THE OPENER
WARNING: YOUR GARAGE DOOR IS THE
LARGEST
MOVING
HOUSE, THE SPRINGS, PULLEYS, CABLES
AND MOUNTING HARDWARE UTILIZED TO
BALANCE
ITS
OPERATION
EXTREME TENSION AT ALL TIMES AND CAN
CAUSE SERIOUS PERSONAL
DEATH, IF DISTURBED.
ADJUSTMENT.
CALL A QUALIFIED SERVICE PERSON TO
MOVE, LOOSEN OR ADJUST DOOR SPRINGS
OR HARDWARE.
REMOVE ALL ROPES AND REMOVE OR
MAKE INOPERATIVE ALL LOCKS CONNECTED
TO THE GARAGE DOOR BEFORE INSTALLING
THE OPENER.
DO NOT WEAR RINGS, WATCHES OR LOOSE
CLOT HING
W HILE
SERVICING
GARAGE
WEAR
SAFETY
GOGGLES
PROTECTIVE EYEWEAR.
IF POSSIBLE, INSTALL THE DOOR OPENER
7zFT OR MORE ABOVE THE FLOOR. MOUNT
THE EMERGENCY RELEASE 6 FT ABOVE THE
FLOOR.
TO REDUCE THE RISK OF SEVERE INJURY
OR DEATH: READ AND FOLLOW ALL
INSTALLATION INSTRUCTIONS!
OR
BINDS
MAY
SYSTEM
FROM
DOOR
IS
PROPERLY
INSTALLATION
ASSEMBLIES
AND
HARDW ARE
BEFORE
OBJECT
IN
YOUR
ARE
UNDER
INJURY, EVEN
DO NOT ATTEMPT
IN ST ALL ING
DOOR
OPENERS.
OR
OTHER
REINFORCE
ALUMINUM AND STEEL DOOR TOP SECTIONS
TO AVOID DAMAGE AND TO INSURE PROPER
OPERATION
SYSTEM.
MANUFACTURER FOR A REINFORCEMENT
OF
KIT.
DO NOT CONNECT THE OPENER TO A
POWER SOURCE UNTIL INSTRUCTED TO DO
SO.
CHECK LOCAL BUILDING AND ELECTRICAL
CODES
FOR MANDATORY INSTALLATION
AND WIRING REQUIREMENTS.
CONNECT
PROPERLY
PERMANENT
CODES, DISCONNECT POWER AT FUSE BOX
OR CIRCUIT BREAKER BEFORE ATTEMPTING
ANY WIRING CONNECTIONS.
LOCATE THE CONTROL PUSH BUTTON:
A. WITHIN SIGHT OF THE DOOR, AND,
B.
AT A MINIMUM HEIGHT OF 5 FT SO SMALL
CHILDREN CAN'T REACH IT, AND,
C.
AWAY FROM MOVING PARTS OF THE
DOOR.
INSTALL THE ENTRAPMENT WARNING LABEL
NEXT TO THE CONTROL PUSH BUTTON IN A
PROMINENT
EMERGENCY RELEASE INSTRUCTION CARD,
ATTACHING
EMERGENCY RELEASE.
ADJUST THE SENSITIVITY ADJUSTMENTS
ENOUGH
OR
OPERATE, BUT NOT SO FIRMLY AS TO EXERT
E X C E S S I V E
OBSTRUCTION BEFORE REVERSING.
AFTER INSTALLING THE OPENER, THE DOOR
SHOULD REVERSE WHEN IT CONTACTS A
1-1/2" HIGH OBJECT (A PIECE OF STANDARD
2 X 4 BOARD LAID FLAT) ON THE FLOOR.
6
LIGHTWEIGHT
FIBERGLASS,
OF
THE
SAFETY
CONTACT
YOUR
POWER
CORD
ONLY
GROUNDED
OUTLET.
WIRING
IS
REQUIRED
LOCATION.
INSTALL
IT
ON
OR
NEXT
TO
ALLOW
THE
P R E S S U R E
REVERSE
DOOR
TO
A
IF
BY
THE
TO
THE
DOOR
TO
O N
A N
Hide quick links:
Advertisement
Table of Contents
