LG 26LH1DC3 - - 26" LCD TV Installation And Operating Manual page 65

Detailed Information For Making A Master TV
IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING...
To set up a master TV you will need to know
how to enter the 26LH1 DC3/4/5 Installer
menu and make changes to the default values
as required. If necessary, familiarize yourself
with the 26LH1DC3/4/5 Installer menu and how to
make and save changes in the menu, before attempting
to clone the 26LH1 DC3/4/5 Master TV setup.
You will also need an Installer remote control similar to
the one shown in the front of this manual.
Finally, the TV's clonable features need to be set up.
This is a critical step. If the Master TV display panel's
clonable features like adding channel icons or channel
labels are not correctly added, then the cloned
26LH1DC3/4/5s TVs will all have problems.
As the cloning procedure is being performed, specific
steps need to be done at the indicated times to achieve
the desired result. Be sure to do each task as indicated.
If a procedure or step is left out or not performed
completely, cloning may not work. At each step, pay
attention to assure the TV screen shows the proper
message when
cloning. If the message indicated does not appear, there
is a problem with that step and cloning may not be
successful. Cloning is only possible when the signal
source is an Analog channel, not a digital channel.
Making a Master TV
Detailed Instructions
The following describes the procedure for preparing a
Master 26LH1 DC3/4/5 for cloning and the procedure
for adding Channel Icons and/or Labels.
Note 1 : Disconnect all Aux inputs. Under certain
conditions, Auto Program Scan is disabled if there is an
Aux input active.
Note 2: Under certain conditions, changes to the input
mode of the RGB inputs will not take effect until the
power is cycled (TV is turned Off and On). To avoid
confusion, disconnect all RGB inputs before entering the
Installer menu.
1. Enter the 26LH1DC3/4/5 installer menu.
a. Reset the internal controller to factory default by
accessing installer menu item 117 FACT DEFAULT, set
it to 1 and press "ENTER". The value will change
back to 0 after the TV's internal controller has been
restored to factory default condition.
b. Within the Installer menu, set the Installer menu
items to the configuration required of your
institution.
c. It is important to set the tuning band at this time,
see
Installer menu item 03 BAND/AFC.
d. Set Installer menu item 28 - CH OVERIDE to 001
to allow access to the Auto Program and Channel
List/Channel Label features in the Channel Menu.
Exit the Installer menu.
2. Access the Master TV menus and set the clonable
options on the menus to the desired configuration.
Refer to the Clonable Menu Features Chart on the
see page 65.
3. Run Auto Program.
4. Enter the Channel List/Channel Label menu and edit
the channel line-up to include the Free-To-Guest
Channels only.
5. Assign ICONs to the channels using the Channel
Label Menu.
Note: You can add Channel ICONS typically network
Iogoslike ABC, NBC, PBS etc. in this step. Or, in Step Z
add Channel ICONS or labels for channels without
Icons.
6. Transfer the TV setup: Enter the 26LH1DC3/4/5
installer menu.
Press '2', '5', '5', 'MENU' to start the transfer of the
TV's setup to the 26LH1DC3/4/5. Once the
transfer is complete, the system will exit the Installer
menu.
Note: Only do 2-5-5 + MENU once. The TV setup
may be corrupted if 255 + Menu is done more than
one time.
Z Edit/Add Channel ICONs and Channel Labels as needed.
Enter Installer menu. With menu displayed, press 2-
5-4 + MENU.
See page 62 for detailed instructions:
- Editing/Adding Channel ICON and Labels on
Master TV
- Changing a Channel's ICON on Master TV
- Changing/Adding Channel Labels on Master TV
- Changing Source Labels on Master TV
8. Verify Master TV setup and feature configuration:
• Did you add Channel ICONS?
• Did you add Channel Labels?
• Did you add Aux Source Labels?
• Did you adjust all TV menu options as required?
The TV master setup is now ready to be cloned.
Go to the master TV cloning section or continue on
to page 52.
After verifying master setup, enter the 26LH1 DC3/4/5
Installer menu and set Installer menu item 028 Ch
Overide to 000.
N
0
r'rl
N
J
>
r-"
0
I'rl
6S