Asus AP1600R-E2BA2 - AP - 1600R-E2 User Manual page 57

3 . 3 . 3 . S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
3 . 3 . S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
If you installed Serial ATA hard disk drives, you can create a RAID 0 or
RAID 1 configuration with the Adaptec
supported by the Intel
These connectors are set to S t a n d a r d I D E
S S S S S t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E
t a n d a r d I D E mode, you can connect Serial ATA boot/data hard disk t a n d a r d I D E
drives to these connectors. If you intend to create a Serial ATA RAID set
using these connectors, set the S A T A
See page 4-27 and 4-28 for details.
NCL-DS1R1 SATA connectors
I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A
• You must install Windows
Service Pack 1 before using Serial ATA hard disk drives. The Serial
ATA RAID feature (RAID 0/RAID 1) is available only if you are using
Windows
• Use only two Serial ATA RAID connectors for each RAID 0 or RAID 1
set.
• When using the connectors in S S S S St a n d a r d I D E
primary (boot) hard disk drive to the SATA1 or SATA2 connector.
Refer to the table below for the recommended SATA hard disk drive
connections.
Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection
C o n n e c t o r C o n n e c t o r C o n n e c t o r C o n n e c t o r C o n n e c t o r
S A T A 1 S A T A 1 S A T A 1
S A T A 1 S A T A 1
S A T A 2 S A T A 2 S A T A 2
S A T A 2 S A T A 2
A S U S A P 1 6 0 0 R - E 2 ( C S 3 ) A S U S A P 1 6 0 0 R - E 2 ( C S 3 ) A S U S A P 1 6 0 0 R - E 2 ( C S 3 )
A S U S A P 1 6 0 0 R - E 2 ( C S 3 ) A S U S A P 1 6 0 0 R - E 2 ( C S 3 )
® 6300ESB South bridge chip.
S t a n d a r d I D E mode by default. In S t a n d a r d I D E S t a n d a r d I D E
S t a n d a r d I D E
S A T A S A T A
S A T A S A T A M o d e
® 2000 Service Pack 4 or the Windows
® 2000/XP.
S e t t i n g S e t t i n g S e t t i n g S e t t i n g S e t t i n g
M a s t e r M a s t e r M a s t e r
M a s t e r M a s t e r
S l a v e S l a v e S l a v e
S l a v e S l a v e
® HostRAID™ technology
M o d e M o d e
M o d e M o d e item in the BIOS to [RAID].
SATA2 SATA1
t a n d a r d I D E mode, connect the t a n d a r d I D E t a n d a r d I D E
t a n d a r d I D E
U s e U s e U s e U s e U s e
B o o t d i s k B o o t d i s k B o o t d i s k
B o o t d i s k B o o t d i s k
D a t a d i s k D a t a d i s k D a t a d i s k
D a t a d i s k D a t a d i s k
® XP
4 - 1 1 4 - 1 1 4 - 1 1
4 - 1 1 4 - 1 1