Table of Contents
Advertisement
GAS HOB
MGH 621
INSTRUCTION BOOKLET
Please read this instruction booklet before using the appliance
Keep this instruction book for future
reference and ensure it is passed on to any
new owner.
3
2
3
1
4
5
6
1. Hob Top
2. Rapid Burner
3. Semi-rapid Burners
4. Auxiliary Burner
5. Control knobs
6. Electric Ignition Push Button
These instructions are only valid for :
GB
Advertisement
Table of Contents
Related Manuals for Moffat MGH 621
Summary of Contents for Moffat MGH 621
- Page 1 GAS HOB MGH 621 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance Keep this instruction book for future reference and ensure it is passed on to any new owner. 1. Hob Top 2. Rapid Burner 3. Semi-rapid Burners 4.
-
Page 2: Important Safety Information
Important Safety Information You MUST read hese warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 950950 Installation This appliance must be installed and serviced by a competent person as stated in the Gas Safety (Installation and Use) Regulations Current Editions and the IEE Wiring Regulations. -
Page 3: Environmental Information
Never use plastic or aluminium foil dishes on the hob. Perishable food, plastic items and areosols may be affected by heat and should not be stored above or below the hob unit. Service This hob should only be repaired or serviced by an authorised Service Engineer and only genuine approved spare parts should be used. -
Page 4: Operation
Operation Hob Burners To light a burner: push the electric ignition push button which is marked by a little spark ( at the same time turn the relevant control knob anticlockwise to maximum position; then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again. -
Page 5: Something Not Working
Something not working If the appliance is not working correctly, please carry out the following checks, before contacting your local Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. -
Page 6: Instructions For The Installer
Instructions for the Installer This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. -
Page 7: Important Safety Requirements
Important safety requirements This hob must be installed in accordance with FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). 700 mm Provision for ventilation Detailed recommendations are contained 400 mm in the following British Standards Codes Of... -
Page 8: Installation
Installation When the hob is first installed Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. On the end of the shaft, which includes the GJ 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. -
Page 9: Building Over A Cupboard Or Drawer
Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2. -
Page 10: Electrical Connections
Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. -
Page 11: Wiring Diagram
Wiring Diagram Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. 1. Turn the gas tap to the MAX position and ignite. 2. Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. -
Page 12: Pressure Testing
Pressure Testing Remove the pan supports and the burner caps and crowns. The pressure testing must be carried out on the burners. Proceed as follows: 1. Fit manometer tube over the injector. 2. Turn on the burner gas supply and ignite another burner. 3. - Page 13 Characteristics of gas burners TYPE OF Characteristics NATURAL 20 mbar LPG GAS 28-30/37 mbar BURNER POSITION NOMINAL THERMAL POWER (kW) NOMINAL FLOW 0.286 RATE (m NOZZLE REFERENCE (1/100 mm) NOMINAL THERMAL POWER (kW) NOMINAL FLOW RATE (g/h) NOZZLE REFERENCE (1/100 mm) RAPID SEMI-RAPID (large)
-
Page 14: Service And Spare Parts
European Guarantee This appliance is guaranteed by Electrolux in each of the countries listed below for the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countries listed below the appliance guarantee will move with you subject to the following qualifications: ·... - Page 16 35676-2903 07/06...
Need help?
Do you have a question about the MGH 621 and is the answer not in the manual?
Questions and answers