Tascam HS-P82 Manual page 6

Trim group function addition
This new trim group function allows you to adjust input trim levels of
multiple channels at the same time with one input trim knob set as
the master
NOTE
Along with the addition of the trim group function, the
item on the
Key Assign
screen has a new
SETUP MIXER (TRIM GROUP)
Setting trim groups
ª
To use trim group operation, you must assign one channel as the
master of the group and other channels as slaves.
There are four groups, and multiple combinations are possible.
NOTE
You cannot assign a channel to more than one group. The channel
•
is always assigned to the last group selected.
Only the input trim knob of the designated master can be used to
•
adjust the input level. Turning the knobs of the slaves will have no
effect.
1 Press the MENU key to open the Menu Screen, and press
the button to open the
MIXER SETUP
screen.
2 Touch the
TRIM GROUP
page.
The item contains buttons numbered
TRIM GROUP
for each channel. Touch the corresponding buttons to assign
each channel to groups 1–4.
In this example, we will make channel
1 and channels , - (link),
2 3 4
3 Under the channel that you want to make the master, touch
the number button ( –
1 4
channels assigned to it yet.
The letter appears to the right of the number and the
M
button becomes red.
In the example, touch the
appears and the button becomes red.
NOTE
The first channel assigned to a group becomes its master. The master
cannot be changed afterwards. If you want to change the master,
clear the grouping and start again, assigning the channel that you
want as the master to the group first.
4 Touch the group number button under the channel that you
want to make a slave. The button becomes blue.
Slaves can be channels of numbers lower than the master and
channels that are not consecutive.
For example, if you press the
button becomes blue. Likewise, you can press the
under channels - , and
3 4 5
indicating that they are slaves.
5 By turning the input trim knob for channel
the trim values for channels
6
TASCAM HS-P82
Function
page of the
RC-F82 REMOTE
setting.
MIXER SETUP
tab to open the
TRIM GROUP
the master for group
1
and into slaves.
5 6
) for a group that does not have any
button beneath channel
1
button under channel
1
1
and they will also become blue,
6
, you can adjust
1
, - , and together.
2 3 4 5 6
NOTE
If the trim setting for any of the grouped channels reaches its
•
maximum or minimum value, continuing to turn the input trim
knob of the master in the same direction will have no further
affect on any of the channels. (The differences in values between
channels are preserved.)
Channels cannot be linked if they are in different groups (including
•
when one is not in a group). Touching the button for those
channels in the
warning to appear.
Clearing a trim group
ª
To clear a trim group, touch the master button for that group
(the button that appears red and has the letter
group number).
A pop-up appears to confirm that you want to clear the group.
Touch the
OK
Doing this clears the group setting from the slaves (channels with
blue buttons) at the same time.
–
1 4
If you try to assign a channel that is a group master to another
group, a pop-up appears to confirm that you want to clear its group
and assign it to a different group. Touch the
DATA
dial to clear the previous group and assign the channel that
had been its master to the other group.
.
1 1M
Zero trim function added
Turning an input trim knob to its minimum setting now results in that
channel being muted.
Each trim knob functions the same as before, but when it reaches its
minimum setting, the channel is muted regardless of the reference
level setting.
, that
2
buttons
item will cause the following pop-up
CH LINK
DATA
button or press the dial to clear the group.
HS-P82
next to the
M
button or press the
OK