Parameters From The Pre-Amplifier Unit - Yamaha CP1 Owner's Manual

Parameters from the Pre-Amplifier Unit

Editing Sequence: Press and hold the [PRE-AMPLIFIER 1] or [PRE-AMPLIFIER 2] button (for at least one second)
 Turn Knobs 1 to 6
Pre-amplifiers are set automatically based on the type of piano selected; however, the following parameters can be used
to modify the way in which each Pre-Amplifier unit affects the corresponding piano sound. Each different preamp type is
configured using a different set of parameters. In the following table, you will find a description of all such parameters in
alphabetic order.
On-screen name Associated piano types
(and full name)
B Bass CF 3Band, S6 3Band, CP80,
CP88, 71Rd I, 73Rd I, 75Rd I,
78Rd II, Dyno, 69Wr, 77Wr
Brill. CP80, CP88
(Brilliance)
D Depth
71Rd I, 73Rd I, 75Rd I, 78Rd II,
69Wr, 77Wr
(Vibrato Depth)
G Gain All types
(Input Gain)
H High DXEP 1 to DXEP 4
HighMid DXEP 1 to DXEP 4
(High Middle)
L Low DXEP 1 to DXEP 4
LowMid DXEP 1 to DXEP 4
(Low Middle)
M Mid CF 3Band, S6 3Band
Middle CP80, CP88
MidBoost 69Wr, 77Wr
(Mid Boost)
MidFreq CF 3Band, S6 3Band
(Mid Frequency)
N Normal Dyno
O Overtone Dyno
P Pk1Freq CF 2Band, S6 2Band
(Peak1 Frequency)
Pk1Gain CF 2Band, S6 2Band
(Peak1 Gain)
Pk2Freq CF 2Band, S6 2Band
(Peak2 Frequency)
Pk2Gain CF 2Band, S6 2Band
(Peak2 Gain)
S Speed 71Rd I, 73Rd I, 75Rd I, 78Rd II
(Vibrato Speed)
T Treble CF 3Band, S6 3Band, CP80,
CP88, 71Rd I, 73Rd I, 75Rd I,
78Rd II, 69Wr, 77Wr
V Volume All types
NOTE Output from a pre-amplifier will be muted briefly whenever one of the following tone-control parameters is modified.
• CP80 or CP88 pre-amplifier: Bass, Middle, Treble, or Brill
• 71Rd I, 73Rd I, or 75Rd I pre-amplifier: Bass
• 78Rd II pre-amplifier: Treble
• Dyno pre-amplifier: Bass or Overtone
Description
This parameter is used to adjust the volume of the low-frequency component.
This parameter is used to adjust the brightness of the sounds produced.
This parameter is used to adjust the depth of the pre-amplifier vibrato.
This parameter is used to adjust the volume of the signal input into the pre-amplifier.
This parameter is used to adjust the volume of the high-frequency component.
This parameter is used to adjust the volume of the high mid-frequency component.
This parameter is used to adjust the volume of the low-frequency component.
This parameter is used to adjust the volume of the low mid-frequency component.
This parameter is used to adjust the volume of the mid-frequency component.
This parameter is used to adjust the volume of the mid-frequency component.
This parameter is used to adjust the volume of the mid-frequency component.
This parameter is used to adjust the frequency of the mid-frequency component.
This parameter is used to adjust the volume of the mid-frequency component.
This parameter is used to adjust the volume of the high-frequency component.
This parameter is used to adjust the central frequency of Peak1 (i.e., Peaking Filter
1).
This parameter is used to adjust the volume of Peak1 (i.e., Peaking Filter 1).
This parameter is used to adjust the central frequency of Peak2 (i.e., Peaking Filter
2).
This parameter is used to adjust the volume of Peak2 (i.e., Peaking Filter 2).
This parameter is used to adjust the speed of the pre-amplifier vibrato.
This parameter is used to adjust the volume of the high-frequency component.
This parameter is used to adjust the output volume. If set to 100 or greater when
71Rd I, 73Rd I, 75Rd I, 78Rd II, 69Wr, or 77Wr has been set as the part's piano
type, drive will also be added to the sound.
Piano
45
CP1 Owner's Manual