Kyocera KM-4230 Instruction Handbook Manual
F-4220 instruction hb
Hide thumbs
Also See for KM-4230:
- Service manual (602 pages) ,
- User manual (310 pages) ,
- Operation manual (100 pages)
Related Manuals for Kyocera KM-4230
Summary of Contents for Kyocera KM-4230
- Page 1 F-4220 INSTRUCTION HANDBOOK ALWAYS read this Instruction Handbook thoroughly before use. After reading, maintain it in good condition and keep it together with the Instruction Handbook for your copier.
- Page 3 ALWAYS read this Instruction Handbook thoroughly before use. After reading, maintain it in good condition and keep it together with the Instruction Handbook for your copier. Refer to the Instruction Handbook for your copier for information on the service representative for your product. The sections of this handbook and parts of the product marked with symbols are safety warnings meant to protect the user, other individuals and surrounding objects, and ensure correct...
-
Page 4: Table Of Contents
Contents INSTALLATION PRECAUTIONS ........2 PRECAUTIONS FOR USE ..........3 Names of parts................4 Cautions During Copying ............5 Various Modes ................5 Sort Mode ................5 Group Mode................5 Sort-Staple Mode..............5 Booklet copy Mode ..............5 Troubleshootiong ..............7 A. How to handle paper jam at finisher........7 B. How to replenish finisher stapler .........8 C. -
Page 5: Installation Precautions
INSTALLATION PRECAUTIONS Environment Power supply/Grounding the product CAUTION WARNING • DO NOT use a power supply with a voltage other than • Avoid placing the product on or in locations which are that specified. Avoid multiple connections in the same unstable or not level. -
Page 6: Precautions For Use
PRECAUTIONS FOR USE Cautions when using the product • If dust accumulates within the product, there is a danger of fire or other trouble. It is therefore recommended that you consult with your service WARNING representative in regard to cleaning of internal parts. •... -
Page 7: Names Of Parts
Names of parts 1 Saddle eject tray 1 (Finished copies are delivered to this 9 Finisher unit lever (Handle for adding staples for the tray.) finisher or when a staple jam occurs in the finisher.) 2 Saddle eject tray 2 (Printed sheets are delivered to this 0 Staple holder (Staples are set here.) ! Stitcher unit tray.) -
Page 8: Cautions During Copying
Cautions During Copying/Various Modes Cautions During Copying * If finished copies come out curled or are stacked unevenly, turn the paper in the cassette over and set it again. * If the flap of envelopes is triangular, copies may be stacked unevenly in the tray. -
Page 9: Various Modes
Various Modes 2. Booklet + cover copy mode This mode can be used to include covers, either blank or with an image copied onto the front cover, with the output when carrying out booklet copying. 3. Stitching mode This mode can be used to copy duplex or one sided originals into duplex copies with two pages on each side and to staple the copies arranged in order of page into a booklet with a cover such as a weekly magazine or a pamphlet. -
Page 10: Troubleshootiong
Troubleshooting A. How to handle paper jam at finisher 1. Hold the part of the finisher shown in the below illustration, and release the finisher from the machine body. 2. Remove the paper sticking out from the finisher. 3. Open the top cover, and check the inside. 4. -
Page 11: How To Replenish Finisher Stapler
Troubleshooting 7. Attach the finisher to the machine body. 8. Then follow the instruction displayed on the front panel. B. How to replenish finisher stapler When a message of replenishing stapler displays at front panel, follow below procedure to replenish. 1. -
Page 12: How To Handle Finisher Stapler Jam
Troubleshooting 5. Set the new stapler case to the unit. Note: Stapler can only be set one at a time. Please use the stapler exclusive use for this model. 6. Remove the tape holding the stapler straight upward. 7. Fit the stapler unit all the way to the machine, until the green lever goes up. -
Page 13: Troubleshooting
Troubleshooting 3. Release the green cover down. 4. The stapler unit will come out a little, hold the right and left side, and pull the unit out. 5. Push down the stapler cartridge lever down. 6. Remove the stapler which you can slide it out from the unit. 7. -
Page 14: How To Handle Paper Jam At Saddle Stitcher
Troubleshooting D. How to handle paper jam at saddle stitcher When a message of saddle stitcher jam displays at front panel, follow below procedure. 1. Hold the part of the finisher shown in the below illustration, and release the finisher from the machine body. 2. -
Page 15: How To Replenish Saddle Stitcher Stapler
Troubleshooting 7. Close the front lower cover. 8. Attach the saddle finisher to the machine body. 9. Then follow the instruction displayed on the front panel. E. How to replenish saddle stitcher stapler When a message of replenishing saddle stitcher stapler displays at front panel, follow below procedure. -
Page 16: How To Handle Saddle Stitcher Stapler Jam
Troubleshooting 5. Install new cartridge. Note: When replenishing, replace both stapler at once. 6. Pull the stitcher toward you, then fit back the stitcher to the original position. 7. Push back the stitcher unit in, and close front lower cover. F. - Page 17 Troubleshooting 4. Remove the stapler cartridge by pulling both end. 5. Push down A, then lift up the B. 6. Remove the stapler which is caught, then push B back to the position. 7. Install back the cartridge. 8. Pull the stitcher toward you, then fit back the stitcher to the original position.
-
Page 18: Specifications
Specifications 1. Finisher section Item Description Stacking system Trays 1 and 2: Tray rising and falling system Face down stacking Stacking orientation Face up stacking Paper sizes to be AB series: A3, A4, A4R, A5, A5R, B4, B5, B5R, postcard stacked Inch series: 11"... - Page 19 Specifications 2. Saddle stitcher section Item Description Center stapling, folded into two Stitching system A3, B4, A4R, 11" x 17", and LTRR Paper sizes Without stitching: 1 sheet Number of sheets (including one cover) With stitching : 2 - 15 sheets 64 g/m - 80 g/m (up to 200 g/m...
- Page 20 WARNING This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
- Page 21 This machine has passed all quality controls and final inspection.
- Page 22 2000. 7 5C180031B...