Advertisement
1.2.3 Configuration of Keyboard, Sequencer, and Tone Generator Sections
KEYBOARD
track trns ch
MIDI IN
1 16
omni
kbd
rec ch
SEQUENCER
track trns ch
rcv ch
TONE GENERATOR
NOTE: Note on messages transmitted to the tone generator will be independent
among keyboard, sequencer and MIDI. Controller information (control change,
aftertouch, and pitch bend, etc.) will not be independent.
2. System Exclusive Messages
2.1 General MIDI Mode On
Reset the following controller settings.
VOLUME
PAN
PROGRAM CHANGE
BANK SELECT MSB
SYS EFFECT SEND1
SYS EFFECT SEND2
SYS EFFECT SEND3
PITCH BEND
MODULATION
EXPRESSION
SUSTAIN SWITCH
PRN
PORTAMENT CONTROL
PITCH BEND RANGE
FINE TUNING
COARSE TUNING
"GM on" messages will not be received when the W5/W7 is in Voice Edit Mode.
2.2 Parameter Change
The W5/W7 will receive the eight types of parameter change messages listed below.
However, 6) Switch Remote will only receive and it will act the same function as the
panel switches.
1). Song/Multi Data
2). Normal Voice Data
3). Drum Voice Data
4). Element Data
5). Setup Data
6). Switch Remote
7). Master Tuning
8). Universal System Exclusive Message
Except for Device Number off, the parameter change reception cannot be turned off
with each MIDI switch.
2.2.1 W5/W7 Data parameter change
(1) Format
11110000
F0
01000011
43
0001nnnn
nnnn
00110011
33
0000gggg
gggg
0sssssss
sssssss
0ppppppp
ppppppp
0ppppppp
ppppppp
0vvvvvvv
vvvvvvv
0vvvvvvv
vvvvvvv
11110111
F7
MIDI OUT
local on/off
rcv ch
100
Center
1(Grandpno)
0
64
0
0
0(Center)
0(Off)
127(Maximum)
0(Off)
Condition of undetermined number
Reset
02(2-1/2 octaves)
0
0
= Device Number
= Parameter Group Number
= Parameter Sub Group Number
= Parameter Number MSB7bit
= Parameter Number LSB7bit
= Data Value MSB7bit
= Data Value LSB7bit
(2) Parameter Group Number, Sub Group Number
Parameter Group Name
gggg
Element Data
0
Normal Voice Data
1
Drum Voice Data
2
Song/Multi Data
4
Setup Data
7
Switch Remote
13
*1: cccceee
c = 0..15;Inst Channel(1..16)
e = 1..4 ;Element Number
*2: cccceee
c = 0..15;Inst Channel(1..16)
e = 1..4 ;Element Number, 0;common data
*3: cccceee
c = 0..15;Inst Channel(1..16)
e = 1;key data, 0;common data
*4: ccccccc
c = 1..16;Inst Channel(1..16)
= 0;common data
(3) Parameter Number, Data Value
See Appended Table below, page 44.
(4) Operation
(Reception)
1) ~ 6)
All Mode: Modes are received as they are. (No page change.)
7) This parameter change is only for reception. Remote controlling is possible with all
the panel switches. This message has the same effect as pressing the switch.
2.2.2 Master Tuning parameter change
(1) Format
11110000
F0
01000011
43
0001nnnn
nnnn
00101001
04
01000000
40
0vvvvvvv
vvvvvvv
11110111
F7
(2) Operation
(Reception)
All Mode: Modes are received as they are. (No page change.)
2.2.3 Identify Reply
(1) Format
W7:
11110000
F0
01000011
7E
0nnnnnnn
nnnnnnn
00000110
06
00000010
02
01000011
43
00000000
00
01000001
41
00010011
13
00000001
01
mmmmmmm
0mmmmmmm
00000000
00
0vvvvvvv
vvvvvvv
00000000
00
11110111
F7
W5:
11110000
F0
01000011
7E
0nnnnnnn
nnnnnnn
00000110
06
00000010
02
01000011
43
00000000
00
01000001
41
00101101
2D
00000001
01
0mmmmmmm
mmmmmmm
00000000
00
0vvvvvvv
vvvvvvv
00000000
00
11110111
F7
sssssss
*1
*2
*3
*4
0
0
= Device Number
= Data Value
= Non Real-time Universal Sys.Ex
= Device Number
= General Information(sub-ID #1)
= Device Identify Reply
= YAMAHA ID
= Device family code LSB
= Device family code MSB
= Device number code LSB
= Device number code MSB
= Minor Version No.
= Major Version No.
= Non Real-time Universal Sys.Ex
= Device Number
= General Information(sub-ID #1)
= Device Identify Reply
= YAMAHA ID
= Device family code LSB
= Device family code MSB
= Device number code LSB
= Device number code MSB
= Minor Version No.
= Major Version No.
4 1
Advertisement
