Advertisement
MIDI DATA FORMAT
1. Tone Generator
1.1 MIDI reception/transmission block diagram
(MIDI reception condition) 1/2
<each ch>
<each ch>
MIDI
sw1
<each ch>
sw2
<each ch>
<each ch>
<each ch>
NOTES:
sw1: Setting MIDI Program Change to "on" turns sw1 on.
sw2: Settings other than MIDI Program Change "off" turns sw2 on.
(MIDI reception condition) 2/2
MIDI
$F0,$43,$10,$33,$0F,$00
$F0,$7E,$cc,$06,$01
$F0,$7E,$7F,$09,$01
$F0,$7F,$7F,$04,$01
off
<Dev No>
$F0,$43,$0n,$7A
(LM__0147VC)
$F0,$43,$0n,$7A
(LM__0147DR)
$F0,$43,$0n,$7A
(LM__0147EL)
$F0,$43,$0n,$7A
(LM__0147EM)
$F0,$43,$0n,$7A
(LM__0147MU)
$F0,$43,$0n,$7A
(LM__0147SY)
$F0,$43,$1n,$33,$xx
$F0,$43,$1n,$04,$40
$F0,$43,$2n,$7A
(LM__0147VC)
$F0,$43,$2n,$7A
(LM__0147DR)
$F0,$43,$2n,$7A
(LM__0147EL)
$F0,$43,$2n,$7A
(LM__0147EM)
$F0,$43,$2n,$7A
(LM__0147MU)
$F0,$43,$2n,$7A
(LM__0147SY)
$F0,$43,$2n,$7A
(LM__0147WH)
Dev No = Device Number
MIDI-Datenformat
Données de Format MIDI
$FE ACTIVE SENSING
$8n NOTE OFF
$9n NOTE ON/OFF
$Bn,$xx Each controller
$Bn,$xx
$Bn,$20
$Bn,$00 BANK SELECT
$Cn PROGRAM CHANGE
$Dn AFTER TOUCH
$En PITCH BENDER
SW REMOTE
IDENTIFY REQUEST
GENERAL MIDI MODE ON
MIDI MASTER VOLUME
NORMAL VOICE bulk
DRUM VOICE bulk
ELEMENT bulk
ELEMENT Map bulk
SONG/MULTI bulk
SYNTH SETUP bulk
PARAMETER CHANGE
PARAMETER CHANGE
(Master Tuning)
same as DX1 format
NORMAL VOICE bulk D.req.
DRUM VOICE bulk D.req.
ELEMENT bulk D.req.
ELEMENT Map bulk D.req.
SONG/MULTI bulk D.req.
SYNTH SETUP bulk D.req.
WAVE HEADER bulk D.req.
(MIDI transmission condition)
ACTIVE SENSING
NOTE ON/OFF
$9n
MODULATION WHEEL
$Bn,
$01
FOOT CONTROL
$Bn,
$04
VOLUME
$Bn,
$07
SUSTAIN SWITCH
$Bn,
$40
DATA ENTRY
$Bn,
$06
AFTER TOUCH
$Dn
PITCH BEND
$En
BANK SELECT
$Bn,
$00
$20
PROGRAM CHANGE
$Cn
VOICE bulk
ELEMENT bulk
SONG/MULTI bulk
SYNTH SETUP bulk
PARAMETER CHANGE
IDENTIFY REPLY
NOTES:
sw1: Setting MIDI Program Change to "on" turns sw1 on.
sw2: Settings other than MIDI Program Change "off" turns sw2 on.
1.2 Channel Message
1.2.1 Transmission
1.2.1.1 Note on/off
Transmission note range = C-2(0)...G8(127)
Velocity range
= 1...127
1.2.1.2 Control change
Control change is output via MIDI when the following controllers are used.
ctrl#
parameter
1
Modulation Wheel
4
Foot Controller
7
Foot Volume
11
Expression
64
Sustain Switch
1 119
Continuous Slider
Program Change
sw1 on
Program Change
<T ch>
sw2 on
transmit
ch
<Dev No>
off
data rng
0
127
0
127
0
127
0
127
0
127
0
127
MIDI
3 9
Advertisement
