Table of Contents
Advertisement
Setting the VCR Output Channel
Your VCR output channel may need to be changed if the pictures
suffer from interference or if your TV cannot find the pictures.
Also, you can change the VCR output channel to adjust the
frequency in which information is displayed on the screen.
PROG
OPTIONS
INSTALL
INSTALL
1
Press MENU on the remote control.
Result:
CLOCK
BONUS
LANG
INSTALLATION
2
Press the corresponding
INSTALLATION
➛❿!!
OK
END:
MENU
" ❷!!
3
Press the OK button to select this option.
Result:
4
Press the corresponding
INSTALL
AUTO SET UP
CH
option is selected.
MANUAL SET UP
TV SYSTEM
:K
VCR OUTPUT CH :CH36
5
Select the required output channel (CH21~CH69) by pressing the
➛ or ❿ buttons.
6
On completion, press MENU twice to exit the menu.
❿
END:
MENU
" ❷
Then tune your television again (see page 13).
Selecting the RF OUT Sound Mode (B/G-D/K-I)
You can choose the sound mode (B/G, D/K or I) according to the
TV set connected to your VCR.
1
PROG
OPTIONS
INSTALL
INSTALL
Press MENU on the remote control.
Result:
CLOCK
BONUS
LANG
2
Press the corresponding
INSTALLATION
INSTALLATION
➛❿!!
" ❷!!
OK
END:
MENU
3
Press the OK button to select this option.
Result:
4
Press the corresponding
option is selected.
INSTALL
AUTO SET UP
MANUAL SET UP
5
Press the ❿ button to select K, G or I.
TV SYSTEM
:K
VCR OUTPUT CH :CH36
6
On completion, press MENU twice to exit the menu.
❿
END:
MENU
" ❷
16
The programming menu is displayed.
or ➛, ❿ buttons to select the
,
"
❷
option.
The
INSTALLATION
menu is displayed.
or
buttons, until the
VCR OUTPUT
"
❷
The programming menu is displayed.
,
or ➛, ❿ buttons to select the
"
❷
option.
The
INSTALLATION
menu is displayed.
or
buttons, until the
TV SYSTEM
"
❷
Presetting the Stations Automatically
You do not need to preset the stations if you have already
set them automatically (see Plug & Auto Set Up on
page 12).
Your VCR contains a built-in tuner used to receive television
broadcasts.
You must preset the stations received through the tuner. This can
be done:
Plug & Auto Set up (see page 12)
Automatically
Manually (see page 18)
You can store up to 50 stations.
To enable the VCR to decode a scrambled TV station, the
decoder must be activated after the scan (see pages 18).
1
Press the MENU button on the remote control.
Result:
The programming menu is displayed.
2
or ➛, ❿ buttons to select the
Press the corresponding
,
"
❷!
INSTALLATION
option.
3
Press the OK button to select this option.
Result:
The
INSTALLATION
menu is displayed.
4
Press the corresponding
or
buttons, until the
"
❷
option is selected. And then press the ❿ button to select this
UP
option.
5
Press OK to start the auto scanning.
Result:
The
PLEASE WAIT
indication flashes on the
television screen.
The first frequency band is scanned and the first
station found is displayed and stored.
The VCR then searches for the second station and so on.
When the automatic scanning procedure has
finished, the VCR switches automatically to pro-
gramme 1.
The number of stations automatically stored by the VCR
depends on the number of stations that it has found.
6
If you wish to cancel the auto scanning before the end, press the
MENU button three times to exit the menu.
Once the auto scanning procedure has finished, some
stations may have been stored more than once; select
the stations with the best reception and delete the
ones no longer required (see page 19).
INSTALL
PROG
OPTIONS
INSTALL
CLOCK
BONUS
LANG
INSTALLATION
➛❿!!
OK
END:
MENU
" ❷!!
INSTALL
AUTO SET UP
MANUAL SET UP
TV SYSTEM
:K
VCR OUTPUT CH :CH36
❿
END:
MENU
" ❷
AUTO SET
YOUR DATA WILL BE LOST
PRESS
OK
TO CONTINUE
MENU
TO EXIT
AUTO SET UP
PLEASE WAIT
2%
I--------------------I
END:MENU
17
GB
Advertisement
Table of Contents
