Table of Contents
Advertisement
VCR
Using the G-CODE Feature
GB
OK
Before presetting your DVD-VCR:
Up to six programmes can be preset.
1
1
Timer Method
Standard
2
G-Code
3
4
G-Code
Code
Code
: 0 - 9
Correct
:
5
6
7
8
STANDBY/ON
OPEN/CLOSE
7
KARAOKE SEARCH
KARAOKE
™ G-CODE is a trademark of Gemstar Development Corporation. The G-CODE system is
manufactured under licence from Gemstar Development Corporation.
32
Switch on both the television and your DVD-VCR
Check that the date and time are correct
Insert the cassette on which the programme is to be
recorded (safety tab intact)
Press the TIMER button.
Result:
The
Timer Method
is displayed.
Press the corresponding
or
buttons, until the
G-Code
option
œ
❷
is selected.
Press the ❿¤button to select
G-Code
.
Result:
A message is displayed to allow you to enter the
G-Code code.
If all six programmes have been set, the message
Timer
is Full
is displayed. Refer to page 35 if you wish to
cancel a preset recording.
Press the numeric buttons to enter the code opposite the pro
gramme that you wish to record in your television magazine.
If you wish to correct the G-Code code that you are
entering:
Press the ➛ button until the digit to be corrected is
cleared
Enter the correct digit
Press the OK button.
Result:
The information concerning the programme is displayed.
When using the G-Code function for the first time with
stored stations, the programme number flashes. This one
time, you must enter the station number manually by
pressing the
or
buttons. Refer to the following page if:
œ
❷
The programme number or times flash
You wish to modify the programme
If the programme and times are correct, press the RETURN button.
Press the STANDBY/ON button to activate the timer.
Refer to page 35 if you wish to:
Check that your VCR has been programmed correctly
Cancel a preset recording
The numbers next to each TV programme listing are
G-CODE code numbers, which allow you to programme
your videorecorder instantly with the remote control. Tap
in the G-CODE code for the programme you wish to
record.
Modifying G-CODE Programming
If you wish to correct the programme displayed or modify certain elements, such as the recording
speed, you can do so before you press M
a second time to confirm.
ENU
If you wish to...
Then...
Press the ➛ or ❿ buttons, until the
Select an input source other
than the tuner (LINE IN)
Press the INPUT SEL. button one or more times to change the
input source selection.
Result:
The input source must be selected before changing any
other value.
Press the ➛ or ❿ buttons, until the
Record a programme every day
(Monday to Sunday) at the same time
Press the
displayed.
Press the ➛ or ❿ buttons, until the
Record a programme every week
on the same day and at the same time
Press the
displayed, followed by the required day.
Example:
Press the ➛ or ❿ buttons, until the
Extend the recording time
Press the
time.
Press the ➛ or ❿ buttons, until the recording speed selection
Select the recording speed
flashes.
Press the
displayed:
• AUTO
• SP
(Standard Play)
• LP
(Long Play)
VCR
selection flashes.
PR
The programme number is replaced by:
•
The LINE IN source using the INPUT SEL.
button for a satellite tuner or external video
source
DAY
selection flashes.
œ
or
❷
buttons, until the
DLY
(Daily) value is
DAY
selection flashes.
or
buttons, until the
W-
(Week) value is
œ
❷
W-SA
(Weekly Saturday)
STOP
selection flashes.
or
buttons to increase or decrease the stop
œ
❷
œ
or
❷
buttons until the correct indication is
(Auto Tape Speed Select) : see page 29
33
GB
Advertisement
Table of Contents
