Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Dell Manuals
  4. Server
  5. PowerEdge 650
  6. Replacement instructions manual

Dell PowerEdge 650 Replacement Instructions Manual

Replacing the system and backplane board assemblies
Hide thumbs Also See for PowerEdge 650:

Advertisement

Quick Links

Download this manual See also: Installation Manual
Dell™ PowerEdge™ 650 Systems
Replacing the System and

Backplane Board

Assemblies
w w w . d e l l . c o m | s u p p o r t . d e l l . c o m

Advertisement

loading

Related Manuals for Dell PowerEdge 650

Summary of Contents for Dell PowerEdge 650

  • Page 1: Backplane Board

    Dell™ PowerEdge™ 650 Systems Replacing the System and Backplane Board Assemblies w w w . d e l l . c o m | s u p p o r t . d e l l . c o m...

  • Page 2: Notes, Notices, And Cautions

    Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
  • Page 3 The system board and backplane board are removed from the chassis as a single assembly, and are then separated for replacement of either board. Removing the System Board/Backplane Board Assembly CAUTION: See your System Information Guide for complete information about safety precautions, working inside the computer, and protecting against electrostatic discharge.
  • Page 4 Loosen the two thumbscrews securing the riser board and disconnect it from the system board card-edge connector. See "Removing the Riser Board" in your Installation and Troubleshooting Guide. Slide the backplane securing latch forward to the open position to allow the system board/backplane board to move to the forward (unlatched) position.
  • Page 5 Figure 1-2. Separating the System/Backplane Board Assembly shroud screws (3) system board backplane board power cable Remove the power cable from the power connector on the system board. See Figure 1-2. Release the plastic cable tie that secures the cable connector to connector U3 and remove the free end of the power cable from the backplane board (connector U3).
  • Page 6 Figure 1-3. Joining the System/Backplane Board Assembly shroud screw center screw hole system board backplane board power cable Connect the free end of the four-conductor power cable that you installed on the back of the backplane (in step 1) to the power connector (CN2) on the system board. Lower the system board/backplane board into the system chassis with the grounding posts through the holes on the system board.
  • Page 7 Replace the cooling shrouds. Install the memory modules, if they were removed. See "System Memory" in your Installation and Troubleshooting Guide. Connect the control panel cable to the front of the backplane. See "Installing the Control Panel Assembly" in your Installation and Troubleshooting Guide. Connect the hard-drive interface cables either to the backplane or through the backplane to the hard-drive controller card, if one is installed.
  • Page 8 Replacing the System and Backplane Board Assemblies...
  • Page 10 Printed in the U.S.A. 0G3929A00 w w w . d e l l . c o m | s u p p o r t . d e l l . c o m...
  • Page 12 Printed in Malaysia. 0G3929A00 w w w . d e l l . c o m | s u p p o r t . d e l l . c o m...
  • Page 14 Printed in China. 0G3929A00 w w w . d e l l . c o m | s u p p o r t . d e l l . c o m...
  • Page 16 Printed in Ireland. 0G3929A00 w w w . d e l l . c o m | s u p p o r t . d e l l . c o m...