1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Switch
  5. 2948G - Catalyst Switch
  6. Hardware installation manual

Cisco 2948G - Catalyst Switch Hardware Installation Manual

Hardware installation guide
Hide thumbs Also See for 2948G - Catalyst Switch:
Table of Contents

Advertisement

Quick Links

See also: Configuration Manual
Catalyst 2984G, 2948G-GE-TX,
and 2980G Switch Hardware

Installation Guide

October 2003
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel:
408 526-4000
800 553-NETS (6387)
Fax:
408 526-4100
Customer Order Number: DOC-786286=
Text Part Number: 78-6286-05

Advertisement

Table of Contents
loading

Related Manuals for Cisco 2948G - Catalyst Switch

Summary of Contents for Cisco 2948G - Catalyst Switch

  • Page 1: Installation Guide

    Catalyst 2984G, 2948G-GE-TX, and 2980G Switch Hardware Installation Guide October 2003 Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 Customer Order Number: DOC-786286= Text Part Number: 78-6286-05...
  • Page 2 You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: •...
  • Page 3 CCIP, CCSP, the Cisco Arrow logo, the Cisco Powered Network mark, Cisco Unity, Follow Me Browsing, FormShare, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet,...

  • Page 5: Table Of Contents

    C O N T E N T S Cisco Limited Lifetime Hardware Warranty Terms Preface Audience Organization Related Documentation Conventions xvii Obtaining Documentation xxiii Cisco.com xxiii Documentation CD-ROM xxiii Ordering Documentation xxiv Documentation Feedback xxiv Obtaining Technical Assistance xxiv Cisco TAC Website...
  • Page 6 Contents Port Locations 10/100 and 10/100/1000 Ports Catalyst 2948G and 2980G Switch Ports Catalyst 2948G-GE-TX Switch Ports Switch Components Management Ports Console Serial Port 10BASE-T and 10/100BASE-T Ports Front Panel LEDs Airflow Power Supplies 1-11 Site Planning C H A P T E R Site Power Requirements and Heat Dissipation System Ground Connection Guidelines (Catalyst 2948G and 2980G Switches Only)
  • Page 7 Contents Installing the Catalyst 2948G and 2980G Switches Required Installation Tools Rack-Mounting the Catalyst 2948G and 2980G Switches Installing the Catalyst 2948G-GE-TX Switch Rack-Mounting the Catalyst 2948G-GE-TX Switch 3-10 Removing Screws from the Switch 3-10 Attaching Brackets to the Switch 3-11 Mounting the Switch in a Rack 3-14...
  • Page 8 Contents Patch Cord 4-10 Patch Cord Configuration Example 4-11 Patch Cord Installation 4-11 Connecting To an SFP Module 4-12 Troubleshooting the Installation C H A P T E R Getting Started Problem Solving to the System Component Level Identifying Startup Problems Troubleshooting the Power Supply Contacting Customer Service Specifications...
  • Page 9 Contents Laser Radiation D-11 Attaching the Cisco RPS (model PWR300-AC-RPS-N1) D-13 Attaching the Cisco RPS (model PWR600-AC-RPS) D-14 Attaching the Cisco RPS (model PWR675-AC-RPS-N1) D-15 Redundant Power Supply Connection Warning D-17 Switch Installation Warning D-18 Chassis Warning for Rack-Mounting and Servicing...
  • Page 10 Contents Catalyst 2984G, 2948G-GE-TX, and 2980G Switch Hardware Installation Guide 78-6286-05...

  • Page 11: Cisco Limited Lifetime Hardware Warranty Terms

    There are special terms applicable to your hardware warranty and various services that you can use during the warranty period. Your formal Warranty Statement, including the warranty applicable to Cisco software, is included on the Cisco Documentation CD and on Cisco.com. Follow these steps to access and download the Cisco Information Packet and your warranty document from the CD or Cisco.com.
  • Page 12 Duration of Hardware Warranty A Cisco product hardware warranty is supported for as long as the original end user continues to own or use the product, provided that the fan and power supply warranty is limited to five (5) years. In the event of a discontinuance of product manufacture, the Cisco warranty support is limited to five (5) years from the announcement of the discontinuance.
  • Page 13 Cisco Limited Lifetime Hardware Warranty Terms Complete the information below, and keep it for reference. Company product purchased from Company telephone number Product model number Product serial number Maintenance contract number Catalyst 2984G, 2948G-GE-TX, and 2980G Switch Hardware Installation Guide...
  • Page 14 Cisco Limited Lifetime Hardware Warranty Terms Catalyst 2984G, 2948G-GE-TX, and 2980G Switch Hardware Installation Guide 78-6286-05...

  • Page 15: Preface

    Preface This preface describes the audience, organization, and conventions of the Catalyst 2984G, 2948G-GE-TX, and 2980G Switch Hardware Installation Guide and provides information on how to obtain related documentation. Audience To use this hardware guide, you should be familiar with electronic circuitry and wiring practices and preferably be an electronic or electromechanical technician.

  • Page 16: Related Documentation

    Preface Related Documentation Chapter Title Description Chapter 4 Gigabit Ethernet Describes the features and configuration of Port Configuration the Gigabit Ethernet ports. Chapter 5 Troubleshooting Provides troubleshooting guidelines for the the Installation initial hardware installation and suggests steps to help isolate and resolve problems. Appendix A Specifications Lists Catalyst 2948G and 2980G switch specifications.

  • Page 17: Conventions

    Preface Conventions Conventions This document uses the following conventions: Convention Description boldface font Commands and keywords are in boldface. italic font Arguments for which you supply values are in italics. Elements in square brackets are optional. { x | y | z } Alternative keywords are grouped in braces and separated by vertical bars.
  • Page 18 Preface Conventions Cautions use the following conventions: Means reader be careful. In this situation, you might do something that could Caution result in equipment damage or loss of data. Warnings use the following conventions: Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury.
  • Page 19 Preface Conventions Varoitus TÄRKEITÄ TURVALLISUUSOHJEITA Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla. SÄILYTÄ...
  • Page 20 Preface Conventions Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.
  • Page 21 Preface Conventions ¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes.
  • Page 22 Preface Conventions Catalyst 2984G, 2948G-GE-TX, and 2980G Switch Hardware Installation Guide xxii 78-6286-05...

  • Page 23: Obtaining Documentation

    These sections explain how to obtain technical information from Cisco Systems. Cisco.com You can access the most current Cisco documentation on the World Wide Web at this URL: http://www.cisco.com/univercd/home/home.htm You can access the Cisco website at this URL: http://www.cisco.com...

  • Page 24: Ordering Documentation

    Cisco Technical Assistance Center (TAC) provides 24-hour, award-winning technical support services, online and over the phone. Cisco.com features the Cisco TAC website as an online starting point for technical assistance. Catalyst 2984G, 2948G-GE-TX, and 2980G Switch Hardware Installation Guide...

  • Page 25: Cisco Tac Website

    The Cisco TAC website (http://www.cisco.com/tac) provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The Cisco TAC website is available 24 hours a day, 365 days a year. Accessing all the tools on the Cisco TAC website requires a Cisco.com user ID and password.

  • Page 26: Obtaining Additional Publications And Information

    Internetworking Terms and Acronyms Dictionary, Internetworking Technology Handbook, Internetworking Troubleshooting Guide, and the Internetworking Design Guide. For current Cisco Press titles and other information, go to Cisco Press online at this URL: http://www.ciscopress.com...
  • Page 27 Preface Obtaining Additional Publications and Information • Packet magazine is the Cisco quarterly publication that provides the latest networking trends, technology breakthroughs, and Cisco products and solutions to help industry professionals get the most from their networking investment. Included are networking deployment and troubleshooting tips, configuration examples, customer case studies, tutorials and training, certification information, and links to numerous in-depth online resources.
  • Page 28 Preface Obtaining Additional Publications and Information Catalyst 2984G, 2948G-GE-TX, and 2980G Switch Hardware Installation Guide xxviii 78-6286-05...

  • Page 29: Chapter 1 Product Overview

    C H A P T E R Product Overview This chapter provides an overview of the features and components of the Catalyst 2948G, 2948G-GE-TX, and 2980G switches. It contains these sections: Switch Description, page 1 • Switch Components, page 7 •...
  • Page 30 Chapter 1 Product Overview Switch Description Figure 1-1 Catalyst 2948G Switch ST AT US Ca tal ys t 29 48 G Figure 1-2 Catalyst 2948G-GE-TX Switch Figure 1-3 Catalyst 2980G Switch SL OT ST AT US CA TA 10 /10 0/1 LY ST 00 0 ET 29 86...

  • Page 31: Gbic Module Support

    Chapter 1 Product Overview Switch Description The Catalyst 2948G switch has 48 autosensing and autoconfiguring 10/100BASE-T Fast Ethernet fixed ports. The Catalyst 2948G-GE-TX switch has 48 autosensing and autoconfiguring 10/100/1000BASE-T ports. The Catalyst 2980G switch has 80 autosensing and autoconfiguring 10/100BASE-T Fast Ethernet fixed ports.

  • Page 32: Switch Features

    Chapter 1 Product Overview Switch Description Catalyst 2948G-GE-TX switch only supports 1000 Mbps and full-duplex modes Note on SFP modules. Except for the 1000BASE-T SFP module, all of the SFP modules are used to establish fiber-optic connections. You use fiber-optic cables with Lucent (LC) connectors to connect to an SFP module.
  • Page 33 Chapter 1 Product Overview Switch Description Table 1-1 Catalyst 2948G, 2948G-GE-TX, and 2980G Switch Features (continued) Feature Description Standard management and Up to 1,024 VLANs with IEEE 802.1Q VLAN tagging on all ports • support (continued) and support for VTP Port aggregation using PAgP for 100-Mbps and 1-Gbps •...

  • Page 34: Port Locations

    Description Embedded management Full SNMP implementation, including entity-MIB, all relevant • standard MIBs, and all relevant Cisco MIBs The first four RMON groups (Ethernet statistics, Alarms, Events, and • History) supported on a per port basis without an optional RMON processing module •...

  • Page 35: Catalyst 2948G And 2980G Switch Ports

    Chapter 1 Product Overview Switch Components Catalyst 2948G and 2980G Switch Ports The Catalyst 2948G switch 10/100BASE-T ports are configured in two rows. The top row contains odd-numbered ports (1 through 47), and the bottom row contains even-numbered ports (2 through 48). The Catalyst 2980G switch 10/100BASE-T ports are configured in four rows.

  • Page 36: Management Ports

    Chapter 1 Product Overview Switch Components • Airflow, page 9 Power Supplies, page 11 • Management Ports The Catalyst 2948G, 2948G-GE-TX, and 2980G switches have two kinds of management ports: console serial and Ethernet. The Catalyst 2948G switches have a 10BASE-T management port. The Catalyst 2948G-GE-TX and 2980G-A switches have a 10/100BASE-T management port.

  • Page 37: Airflow

    Chapter 1 Product Overview Switch Components • PSI LED indicates the internal power supply status on the Catalyst 2948G switch. • PWR LED indicates the internal power supply status on the Catalyst 2980G switch. • RPS LED provides the external redundant power supply status. Table 1-2 describes the LEDs.
  • Page 38 Chapter 1 Product Overview Switch Components If an individual fan fails, the other fans continue to run. Sensors monitor the internal air temperatures. If the air temperature exceeds a tolerable threshold, the environmental monitor displays warning messages. On the Catalyst 2948G-GE-TX, a blower system draws cool air in from the front and sides of the switch and exhausts air out the back.

  • Page 39: Power Supplies

    Note For complete power specifications for the Catalyst 2948G, 2948G-GE-TX, and 2980G switches, see Appendix A, “Specifications.” These switches also be used with an optional Cisco Redundant Power System (RPS). Catalyst 2984G, 2948G-GE-TX, and 2980G Switch Hardware Installation Guide 1-11...
  • Page 40 The Catalyst 2948G switch uses the Cisco RPS 600 AC power supply (PWR600-AC-RPS-CAB). The Cisco RPS 600 supports four external devices that use up to 150 W DC each. Use a one-to-one cable (one connector at each cable end) to connect four external devices to the four DC output power modules.
  • Page 41 Product Overview Switch Components A Cisco RPS can only power one switch at a time. If more than one switch fails at the same time, any subsequent switch is not supported by the RPS until the first switch failure is resolved. For more information, refer to the documentation that was included with your RPS.
  • Page 42 Chapter 1 Product Overview Switch Components Catalyst 2984G, 2948G-GE-TX, and 2980G Switch Hardware Installation Guide 1-14 78-6286-05...

  • Page 43: Chapter 2 Site Planning

    C H A P T E R Site Planning Before you install, operate, or service the system, read the Site Preparation and Warning Safety Guide. This guide contains important safety information you should know before working with the system. Statement 200 Only trained and qualified personnel should be allowed to install, replace, or Warning service this equipment.

  • Page 44: Site Power Requirements And Heat Dissipation

    Site Power Requirements and Heat Dissipation Catalyst 2948G, 2948G-GE-TX, and 2980G switches have internal power Note supplies. All of the switches support Cisco Redundant Power System (RPS) for redundant operation. This section provides site power requirements and heat dissipation specifications for the Catalyst 2948G, 2948G-GE-TX, and 2980G switches.

  • Page 45: System Ground Connection Guidelines

    Chapter 2 Site Planning System Ground Connection Guidelines (Catalyst 2948G and 2980G Switches Only) Table 2-1 Power Requirements and Heat Dissipation Specifications (continued) Power Supply AC Input Model Number/ Output Power Heat Diss Module Type (Watts) (Watts) (BTU/Hr) AC Input Current (Amps) Catalyst 2980G switch 90 VAC: 3.0 120 VAC: 2.4...

  • Page 46: System Ground Connection Guidelines (Catalyst 2948G And 2980G Switches Only)

    One grounding wire (6 AWG recommended)—The length of the grounding wires depends on the location of your switch within the site and its proximity to proper grounding facilities. The grounding wire is not available from Cisco Systems; it is available from any commercial cable vendor.

  • Page 47: Connecting The Switch To Earth Ground

    Chapter 2 Site Planning System Ground Connection Guidelines (Catalyst 2948G and 2980G Switches Only) • Number 2 Phillips head screwdriver. Crimping tool—This must be large enough to accommodate the girth of the • grounding lug when you crimp the grounding cable into the lug. Wire-stripping tool.
  • Page 48 Chapter 2 Site Planning System Ground Connection Guidelines (Catalyst 2948G and 2980G Switches Only) Figure 2-3 Connecting System Ground on the Catalyst 2948G Switch Wire Grounding Screws Grounding lug Figure 2-4 Connecting System Ground on the Catalyst 2980G Switch Wire Grounding Screws Grounding lug...

  • Page 49: Site-Planning Checklist

    Chapter 2 Site Planning Site-Planning Checklist Step 9 Prepare the other end of the grounding wire and connect it to an appropriate grounding point at your site to ensure adequate earth ground for the switch. Site-Planning Checklist Table 2-2 lists the site-planning activities that you should complete before you install the Catalyst 2948G, 2948G-GE-TX, and 2980G switches.
  • Page 50 Chapter 2 Site Planning Site-Planning Checklist Table 2-2 Site-Planning Checklist (continued) Task No. Planning Activity Verified By Time Date Cable and interface equipment evaluation: Cable type Connector type Cable distance limitations Interface equipment (transceivers) EMI evaluation: Distance limitations for signaling Site wiring RFI levels Catalyst 2984G, 2948G-GE-TX, and 2980G Switch Hardware Installation Guide...

  • Page 51: Chapter 3 Installing The Switch

    C H A P T E R Installing the Switch Before you install, operate, or service the system, read the Site Preparation and Warning Safety Guide. This guide contains important safety information you should know before working with the system. Statement 200 Only trained and qualified personnel should be allowed to install, replace, or Warning service this equipment.

  • Page 52: Preparing For Installation

    Chapter 3 Installing the Switch Preparing for Installation Preparing for Installation This section provides information about these topics: • EMC Regulatory Statements, page 2 Checking the Shipping Container, page 4 • EMC Regulatory Statements This section includes specific regulatory statements about the switches. U.S.A.

  • Page 53: Vcci Class A Notice For Japan

    Chapter 3 Installing the Switch Preparing for Installation VCCI Class A Notice for Japan This is a Class A product based on the standard of the Voluntary Control Warning Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.

  • Page 54: Class A Notice For Hungary

    Chapter 3 Installing the Switch Preparing for Installation Class A Notice for Hungary This equipment is a class A product and should be used and installed properly Warning according to the Hungarian EMC Class A requirements (MSZEN55022). Class A equipment is designed for typical commercial establishments for which special conditions of installation and protection distance are used.

  • Page 55: Catalyst 2948G-Ge-Tx Switches

    Chapter 3 Installing the Switch Preparing for Installation • ESD wrist strap Mounting kit • Catalyst 2948G-GE-TX Switches The Catalyst 2948G-GE-TX switch is shipped with these items: This hardware guide • About the Catalyst 2948G Documentation flyer • AC power cord •...

  • Page 56: Installing The Catalyst 2948G And 2980G Switches

    Chapter 3 Installing the Switch Installing the Catalyst 2948G and 2980G Switches Installing the Catalyst 2948G and 2980G Switches Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: •...

  • Page 57: Rack-Mounting The Catalyst 2948G And 2980G Switches

    Chapter 3 Installing the Switch Installing the Catalyst 2948G and 2980G Switches Rack-Mounting the Catalyst 2948G and 2980G Switches To install Catalyst 2940G and 2980G switches in a 19-inch rack, follow these steps: Prepare for installation as follows: Step 1 Place the chassis on the floor or on a sturdy table, as close as possible to the rack.
  • Page 58 Chapter 3 Installing the Switch Installing the Catalyst 2948G and 2980G Switches The L brackets connect the switch chassis to the rack. You can mount the L brackets to the front- or rear-mounting holes of the chassis, depending on which end is in the front of the rack.

  • Page 59: Installing The Catalyst 2948G-Ge-Tx Switch

    Chapter 3 Installing the Switch Installing the Catalyst 2948G-GE-TX Switch Figure 3-2 Installing the Switch in the Rack 17.75 inches (45.09 cm) 17.75 inches (45.09 cm) 17.75 inches (45.09 cm) ST AT US Ca tal ys t 29 48 G Installing the Catalyst 2948G-GE-TX Switch Warning To prevent bodily injury when mounting or servicing this unit in a rack, you...

  • Page 60: Rack-Mounting The Catalyst 2948G-Ge-Tx Switch

    Note with the switch. You can order a kit containing the 24-inch rack-mounting brackets and hardware (order part number RCKMNT-1RU=) from Cisco. Removing Screws from the Switch If you plan to install the switch in a rack, you must first remove screws in the switch chassis so that mounting brackets can be attached.

  • Page 61: Attaching Brackets To The Switch

    Installing the switch in a 24-inch rack requires an optional bracket kit not included Note with the switch. You can order a kit containing the 24-inch rack-mounting brackets and hardware (order part number RCKMNT-1RU=) from Cisco. Figure 3-4 through Figure 3-9 show how to attach each type of bracket to one side of the switch.
  • Page 62 Chapter 3 Installing the Switch Installing the Catalyst 2948G-GE-TX Switch Figure 3-4 Attaching Brackets for 19-Inch Racks, Front Panel Forward Phillips flat-head screws Figure 3-5 Attaching Brackets for 19-Inch Racks, Rear Panel Forward Phillips flat-head screws Catalyst 2984G, 2948G-GE-TX, and 2980G Switch Hardware Installation Guide 3-12 78-6286-05...
  • Page 63 Chapter 3 Installing the Switch Installing the Catalyst 2948G-GE-TX Switch Figure 3-6 Attaching Brackets for 24-Inch Racks, Front Panel Forward Phillips flat-head screws Figure 3-7 Attaching Brackets for 24-Inch Racks, Rear Panel Forward Phillips flat-head screws Catalyst 2984G, 2948G-GE-TX, and 2980G Switch Hardware Installation Guide 3-13 78-6286-05...

  • Page 64: Mounting The Switch In A Rack

    Chapter 3 Installing the Switch Installing the Catalyst 2948G-GE-TX Switch Figure 3-8 Attaching Brackets for 19-Inch Telco Racks Phillips flat-head screws Figure 3-9 Attaching Brackets for 24-Inch Telco Racks Phillips flat-head screws Mounting the Switch in a Rack After the brackets are attached to the switch, use the four supplied number-12 Phillips machine screws to securely attach the brackets to the rack, as shown in Figure 3-10.

  • Page 65: Attaching The Cable Guide

    Chapter 3 Installing the Switch Installing the Catalyst 2948G-GE-TX Switch Figure 3-10 Mounting the Catalyst 2948G-GE-TX Switch In a Rack Phillips machine screws Attaching the Cable Guide We recommend attaching the cable guide to the left or right bracket to prevent the cables from obscuring the front panel of the switch and the other devices installed in the rack.

  • Page 66: Wall-Mounting The Catalyst 2948G-Ge-Tx Switch

    Chapter 3 Installing the Switch Installing the Catalyst 2948G-GE-TX Switch Wall-Mounting the Catalyst 2948G-GE-TX Switch To install the Catalyst 2948G-GE-TX switch on a wall, follow the instructions in these procedures: • Attaching the Brackets to the Switch for Wall-Mounting, page 16 Attaching the RPS Connector Cover, page 17 •...
  • Page 67 Installing the Catalyst 2948G-GE-TX Switch Attaching the RPS Connector Cover If you are not using a Cisco RPS with your switch, use the two Phillips pan-head screws to attach the RPS connector cover to the back of the switch before you...
  • Page 68 Chapter 3 Installing the Switch Installing the Catalyst 2948G-GE-TX Switch To comply with safety regulations, mount the switches on a wall with the front Warning panel facing up. Statement 266 Figure 3-14 Mounting the Switch on a Wall User-supplied screws Catalyst 2984G, 2948G-GE-TX, and 2980G Switch Hardware Installation Guide 3-18 78-6286-05...

  • Page 69: Mounting The Catalyst 2948G-Ge-Tx Switch On A Table Or Shelf

    Chapter 3 Installing the Switch Connecting Power to the Switches Mounting the Catalyst 2948G-GE-TX Switch on a Table or Shelf To install the switch on a table or shelf, follow these steps: Step 1 Locate the adhesive strip with the rubber feet in the mounting-kit envelope. Attach the four rubber feet to the recessed areas on the bottom of the unit.

  • Page 70: Connecting To 10/100 And 10/100/1000 Ports

    Chapter 3 Installing the Switch Connecting to 10/100 and 10/100/1000 Ports If the LEDs or the show system command indicate a power problem or other system problem, see Appendix D, “Translated Safety Warnings” for more information. Connecting to 10/100 and 10/100/1000 Ports The 10/100 ports on the Catalyst 2948G and 2980G switches configure themselves to operate at the speed and duplex settings of attached devices.
  • Page 71 Chapter 3 Installing the Switch Connecting to 10/100 and 10/100/1000 Ports To connect the switch to 10BASE-T, 100BASE-TX, or 1000BASE-T devices, follow these steps: When connecting to servers, workstations, and routers, insert a twisted-pair Step 1 straight-through cable in a front-panel RJ-45 connector, as shown in Figure 3-15.

  • Page 72: Connecting A Terminal To The Console Serial And Ethernet Management Ports

    Chapter 3 Installing the Switch Connecting a Terminal to the Console Serial and Ethernet Management Ports Step 3 Observe the port STATUS LED: The LED turns amber while Spanning Tree Protocol (STP) discovers the • network topology and searches for loops. This process takes about 30 seconds.

  • Page 73: Verifying Switch Operation

    Chapter 3 Installing the Switch Verifying Switch Operation Figure 3-16 Ethernet Cable with RJ-45 Connector Verifying Switch Operation After you have connected all the interfaces, check all connections, and then perform the following steps to power on the system to verify that it is operational: Step 1 Before powering on the system, make sure the connector is installed securely in a grounded outlet at the power-source end of the power cord and that the source...
  • Page 74 Chapter 3 Installing the Switch Verifying Switch Operation When interface LEDs are on, the interface ports may not be functional or enabled. Note Although the LEDs for many interface types might turn on at system startup, they do not indicate an accurate status until the interface is configured. If the system does not complete this verification process, see Chapter 5, Note...

  • Page 75: Chapter 4 Configuring The Gigabit Ethernet Ports

    C H A P T E R Configuring the Gigabit Ethernet Ports Before you install, operate, or service the system, read the Site Preparation and Warning Safety Guide. This guide contains important safety information you should know before working with the system. Statement 200 Only trained and qualified personnel should be allowed to install, replace, or Warning service this equipment.

  • Page 76: Installing, Removing, And Maintaining Gbics

    Chapter 4 Configuring the Gigabit Ethernet Ports Installing, Removing, and Maintaining GBICs Installing, Removing, and Maintaining GBICs The following sections describe Gigabit Interface Converters (GBICs) and how to install, remove, and maintain them: GBIC Features, page 4-2 • • Port Cabling Specifications, page 4-4 GBIC Optical Power Characteristics, page 4-5 •...
  • Page 77 CWDM-GBIC-1530= CWDM-GBIC-1550= CWDM-GBIC-1570= CWDM-GBIC-1590= CWDM-GBIC-1610= Cisco 1000BASE-LX/LH interfaces fully comply with the IEEE 802.3z Note 1000BASE-LX standard. However, their higher optical quality allows them to reach 10 kilometers over single-mode fiber (SMF) versus the 5 kilometers specified in the standard.

  • Page 78: Port Cabling Specifications

    Chapter 4 Configuring the Gigabit Ethernet Ports Installing, Removing, and Maintaining GBICs Because of interoperability issues, Cisco does not support GBICs purchased from Note third-party vendors. Port Cabling Specifications Table 4-2 provides cabling specifications for the GBICs. The minimum cable distance for all GBICs listed (MMF [multimode fiber] and SMF) is 6.5 feet (2...

  • Page 79: Gbic Optical Power Characteristics

    GBIC Optical Power Characteristics Table 4-3 provides the GBIC optical power characteristics. Note For information about the Coarse Wave Division Multiplexing (CWDM), refer to the Cisco CWDM GBIC and CWDM SFP Installation Note. Table 4-3 GBIC Optical Power Characteristics 1000BASE-SX 1000BASE-LX/LH...

  • Page 80: Installing Gbics

    Chapter 4 Configuring the Gigabit Ethernet Ports Installing, Removing, and Maintaining GBICs • When using the 1000BASE-LX/LH GBIC with 62.5-micron diameter MMF, you must install a mode-conditioning patch cord between the MMF fiber-optic network and the GBIC. The mode-conditioning patch cord (CAB-GELX-625 or equivalent) is required to comply with IEEE standards.
  • Page 81 Chapter 4 Configuring the Gigabit Ethernet Ports Installing, Removing, and Maintaining GBICs To install a GBIC, perform these steps: Remove the GBIC from its protective packaging. Step 1 Verify that the GBIC is the correct type for your network by checking the part Step 2 number.
  • Page 82 Chapter 4 Configuring the Gigabit Ethernet Ports Installing, Removing, and Maintaining GBICs Figure 4-3 Installing a GBIC on a Catalyst 2980G Switch SL OT ST AT US CA TA 10 /10 0/1 LY ST 00 0 ET 29 86 HE RE NE T SL OT CO NS...

  • Page 83: Removing Gbics

    Chapter 4 Configuring the Gigabit Ethernet Ports Installing, Removing, and Maintaining GBICs Figure 4-4 Connecting the SC-Type Connector Keys Cable Light out of fiber Receptacle Light into fiber Key slots If you are using the LX/LH GBIC with MMF, you need to install a patch cord Note between the GBIC and the MMF cable.

  • Page 84: Gbic Maintenance Guidelines

    Patch Cord When using the LX/LH GBIC with a 62.5-micron diameter core size MMF, you must install a mode-conditioning patch cord (Cisco product number CAB-GELX-625 or equivalent) between the GBIC and the MMF cable on both the transmit and receive ends of the link. The patch cord is required for link distances greater than 984 feet (300 meters).

  • Page 85: Patch Cord Configuration Example

    LX/LH GBIC is compliant with the IEEE 802.3z standard for 1000BASE-LX. For a detailed description of this problem, refer to Appendix C, “Differential Mode Delay.” Cisco Gigabit Ethernet products have been tested and evaluated to comply with Note the standards listed in Appendix A, “Specifications.”...

  • Page 86: Connecting To An Sfp Module

    Connecting To an SFP Module This section describes how to connect to an SFP module. For instructions about how to install or remove an SFP module, refer to the Cisco Small Form-Factor Pluggable Modules Installation Notes (not orderable but is available on Cisco.com) and to the documentation that came with your SFP module.
  • Page 87 Use only Cisco SFP modules on the Catalyst 2948G-GE-TX switch. Each SFP module has an internal serial EEPROM that is encoded with security information. This encoding provides a way for Cisco to identify and validate that the SFP module meets the requirements for the switch.
  • Page 88 Connecting To an SFP Module For more information about these SFP modules, refer to your SFP module documentation and to the Cisco Small Form-Factor Pluggable Modules Installation Notes (not orderable but is available on Cisco.com.) For the latest information about SFP modules supported by the switch, refer to the release notes.
  • Page 89 Chapter 4 Configuring the Gigabit Ethernet Ports Connecting To an SFP Module Figure 4-7 Connecting to an SFP Module Port Step 3 Insert the other cable end in a fiber-optic receptacle on a target device. Step 4 Observe the port LED. The LED turns green when the switch and the target device have an •...
  • Page 90 Chapter 4 Configuring the Gigabit Ethernet Ports Connecting To an SFP Module Step 5 If necessary, reconfigure and restart the switch or target device. The Gigabit Ethernet ports on these modules are used primarily for backbone interconnection of other high-performance switches and routers. After you have connected all the interfaces, check all connections, and then perform the steps described in the “Verifying Switch Operation”...

  • Page 91: Chapter 5 Troubleshooting The Installation

    C H A P T E R Troubleshooting the Installation This chapter describes how to troubleshoot the Catalyst 2948G, 2948G-GE-TX, and 2980G switch installations. It contains these sections: Getting Started, page 5-2 • Problem Solving to the System Component Level, page 5-2 •...

  • Page 92: Getting Started

    Chapter 5 Troubleshooting the Installation Getting Started Getting Started When the initial system boot is complete, verify the following: • Power supplies are supplying power to the system. On Catalyst 2948G and 2980G switches, the system fan assembly is • operating.

  • Page 93: Identifying Startup Problems

    Chapter 5 Troubleshooting the Installation Identifying Startup Problems If you encounter a problem in performing any of the above checks, you should contact a customer service representative. Identifying Startup Problems LEDs indicate all system states in the startup sequence. By checking the LEDs, you can determine when and where the system failed in the startup sequence.

  • Page 94: Troubleshooting The Power Supply

    If the LED is amber or off, repeat the previous procedure to troubleshoot the second power supply. If the power supply is a Cisco RPS 675 and the LED is amber, the RPS may be in Note standby mode. Press the Standby/Active button on the RPS to put it in active mode and the LED should then turn to green.

  • Page 95: Contacting Customer Service

    Chapter 5 Troubleshooting the Installation Contacting Customer Service If you are using an RPS, do not apply power to the RPS and the switch Note simultaneously. Disconnect power from the internal power supply before turning the power on for the RPS. The RPS contains multiple power supplies for redundant power protection.
  • Page 96 Chapter 5 Troubleshooting the Installation Contacting Customer Service Catalyst 2984G, 2948G-GE-TX, and 2980G Switch Hardware Installation Guide 78-6286-05...

  • Page 97: Appendix

    A P P E N D I X Specifications This appendix provides management port and technical specifications for the Catalyst 2948G, 2948G-GE-TX, and 2980G switches. Console Serial Port The console serial port is an RJ-45 receptacle. Data terminal ready (DTR) and data set ready (DSR) handshake signals are supported on this port.

  • Page 98: 10Base-T And 10/100Base-T Ethernet Management Ports

    Appendix A Specifications 10BASE-T and 10/100BASE-T Ethernet Management Ports 10BASE-T and 10/100BASE-T Ethernet Management Ports The Ethernet management port on each switch is an RJ-45 receptacle with a Link Status LED. Table A-2 lists the port pinouts. Table A-2 10BASE-T Port Pinouts Signal Direction Description...
  • Page 99 Appendix A Specifications Catalyst 2948G Switch Specifications Table A-3 Catalyst 2948G Switch Specifications (continued) Item Specification Environmental (continued) Humidity (RH), ambient 5% to 95% (noncondensing) nonoperating and storage Altitude, 0 to 65621.7 ft (0 to 2,000 m) operating and nonoperating Switching Components Backplane 12 Gbps full duplex...
  • Page 100 Appendix A Specifications Catalyst 2948G Switch Specifications Table A-3 Catalyst 2948G Switch Specifications (continued) Item Specification Standards Compliance Compliance CE Marking Safety 1950, CSA -C22.2 No. 950, EN 60950, 60950 47, part 15 Class A (FCC), ICES Class A with UTP cables, EN55022 Class A with UTP cables, CISPR22 Class A with UTP cables, AS/NZS 3548 Class A with UTP...

  • Page 101: Catalyst 2948G-Ge-Tx Switch Specifications

    Appendix A Specifications Catalyst 2948G-GE-TX Switch Specifications Catalyst 2948G-GE-TX Switch Specifications Table A-4 lists the Catalyst 2948G-GE-TX specifications. Table A-4 Catalyst 2948G-GE-TX Switch Specifications Item Specification Environmental Temperature, ambient 32°F (0°C) to 104°F (45°C) operating Temperature, ambient –40°F (–40°C) to 167°F (75°C) nonoperating and storage Humidity (RH), ambient 10% to 90%...

  • Page 102: Catalyst 2980G Switch Specifications

    Appendix A Specifications Catalyst 2980G Switch Specifications Table A-4 Catalyst 2948G-GE-TX Switch Specifications (continued) Item Specification Standards Compliance Compliance CE Marking Safety 1950, CSA -C22.2 No. 950, EN 60950, 60950 47, part 15 Class A (FCC), ICES Class A with UTP cables, EN55022 Class A with UTP cables, CISPR22 Class A with UTP cables, AS/NZS 3548 Class A with UTP...
  • Page 103 Appendix A Specifications Catalyst 2980G Switch Specifications Table A-5 Catalyst 2980G Switch Specifications (continued) Item Specification Humidity (RH), ambient 10% to 90% (noncondensing) operating Humidity (RH), ambient 5% to 95% (noncondensing) nonoperating and storage Altitude, operating and 6561.7 ft. (0 to 2,000 m) nonoperating Switching Components Backplane...
  • Page 104 Appendix A Specifications Catalyst 2980G Switch Specifications Table A-5 Catalyst 2980G Switch Specifications (continued) Item Specification Safety 1950, CSA -C22.2 No. 950, EN 60950, 60950 Class A (CFR 47, part 15), ICES -003 Class A, EN55022 Class A, CISPR22 Class A, AS/NZS 3548 Class A, and VCCI Class A with FTP cables EN55022 Class B, CISPR22 Class B, AS/NZS...

  • Page 105: Appendix

    A P P E N D I X Repacking a Switch This appendix provides repacking and shipping instructions for the Catalyst 2948G, 2948G-GE-TX, and 2980G switches if you need to return your switch to the factory. To repack the switch using the original packaging material, follow these steps: Slide the pieces of the packing foam over the switch.
  • Page 106 Appendix B Repacking a Switch Figure B-1 Switch Packing Material Documentation and accessories in poly bag Packing foam Packing foam Packing carton Catalyst 2984G, 2948G-GE-TX, and 2980G Switch Hardware Installation Guide 78-6286-05...

  • Page 107: Appendix

    A P P E N D I X Differential Mode Delay When an unconditioned laser source designed for operation on a single-mode fiber (SMF) cable is directly coupled to a multimode fiber (MMF) cable, differential mode delay (DMD) might occur. DMD can degrade the modal bandwidth of the fiber-optic cable.
  • Page 108 Appendix C Differential Mode Delay DMD does not occur in all deployed fibers; rather, it occurs with certain combinations of worst-case fibers and worst-case transceivers. Gigabit Ethernet is the first technology to experience this problem because of its very high baud rate and its long MMF cable lengths.
  • Page 109 Appendix C Differential Mode Delay modes. This is in contrast to an unconditioned launch, which, in the worst case, might concentrate all of its light in the center of the fiber-optic cable, exciting only two or more modes equally. A significant variation in the amount of DMD is produced from one MMF cable to the next.
  • Page 110 Appendix C Differential Mode Delay Catalyst 2984G, 2948G-GE-TX, and 2980G Switch Hardware Installation Guide 78-6286-05...

  • Page 111: Appendix

    A P P E N D I X Translated Safety Warnings This appendix repeats in multiple languages the warnings in this guide. These translated warnings can be used with other documents related to this guide. Catalyst 2984G, 2948G-GE-TX, and 2980G Switch Hardware Installation Guide 78-6286-05...

  • Page 112: Warning Definition

    Appendix D Translated Safety Warnings Warning Definition Warning Definition Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.
  • Page 113 Appendix D Translated Safety Warnings Warning Definition Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents.
  • Page 114 Appendix D Translated Safety Warnings Warning Definition Advarsel VIKTIGE SIKKERHETSINSTRUKSJONER Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å...
  • Page 115 Appendix D Translated Safety Warnings Warning Definition ¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes.
  • Page 116 Appendix D Translated Safety Warnings Warning Definition Catalyst 2984G, 2948G-GE-TX, and 2980G Switch Hardware Installation Guide 78-6286-05...

  • Page 117: Safety Information Referral Warning

    Appendix D Translated Safety Warnings Safety Information Referral Warning Safety Information Referral Warning Before you install, operate, or service the system, read the Site Preparation Warning and Safety Guide. This guide contains important safety information you should know before working with the system. Statement 200 Waarschuwing Lees de handleiding Voorbereiding en veiligheid van de locatie Handleiding voordat u het systeem installeert of gebruikt of voordat u onderhoud aan het...
  • Page 118 Appendix D Translated Safety Warnings Safety Information Referral Warning Varoitus Ennen kuin asennat järjestelmän tai käytät tai huollat sitä, lue Asennuspaikan valmistelu-jaturvaopas -opasta. Tässä oppaassa on tärkeitä turvallisuustietoja, jotka tulisi tietää ennen järjestelmän käyttämistä. Attention Avant d'installer le système, de l'utiliser ou d'assurer son entretien, veuillez lire le Guide de sécurité...

  • Page 119: Qualified Personnel Warning

    Appendix D Translated Safety Warnings Qualified Personnel Warning Qualified Personnel Warning Warning Only trained and qualified personnel should be allowed to install or replace this equipment. Statement 1030 Waarschuwing Installatie en reparaties mogen uitsluitend door getraind en bevoegd personeel uitgevoerd worden. Varoitus Ainoastaan koulutettu ja pätevä...

  • Page 120: Invisible Laser Radiation Warning

    Appendix D Translated Safety Warnings Invisible Laser Radiation Warning Invisible Laser Radiation Warning Because invisible laser radiation may be emitted from the aperture of the port Warning when no cable is connected, avoid exposure to laser radiation and do not stare into open apertures.

  • Page 121: Laser Radiation

    Appendix D Translated Safety Warnings Laser Radiation Avvertenza Poiché quando nessun cavo è collegato alla porta, da quest’ultima potrebbe essere emessa radiazione laser invisibile, evitare l’esposizione a tale radiazione e non fissare con gli occhi porte a cui non siano collegati cavi. Advarsel Usynlige laserstråler kan sendes ut fra åpningen på...
  • Page 122 Appendix D Translated Safety Warnings Laser Radiation Attention Les fibres ou connecteurs débranchés risquent d'émettre des rayonnements laser invisibles à l'œil. Ne regardez jamais directement les faisceaux laser à l'œil nu, ni d'ailleurs avec des instruments optiques. Warnung Unterbrochene Fasern oder Steckerverbindungenkönnen unsichtbare Laserstrahlung abgeben.

  • Page 123: Attaching The Cisco Rps (Model Pwr300-Ac-Rps-N1

    Translated Safety Warnings Attaching the Cisco RPS (model PWR300-AC-RPS-N1) Attaching the Cisco RPS (model PWR300-AC-RPS-N1) Attach only the Cisco RPS (model PWR300-AC-RPS-N1) to the RPS receptacle. Warning Statement 100B Waarschuwing Slechts de Cisco RPS (model PWR300-AC-RPS-N1) aan de RPS contactdoos verbinden.

  • Page 124: Attaching The Cisco Rps (Model Pwr600-Ac-Rps

    Attaching the Cisco RPS (model PWR600-AC-RPS) Varning! Koppla endast Ciscos RPS (modell PWR300-AC-RPS-N1) till RPS-uttaget. Attaching the Cisco RPS (model PWR600-AC-RPS) Attach only the Cisco RPS (model PWR600-AC-RPS) to the RPS receptacle. Warning Statement 112 Waarschuwing Slechts de Cisco RPS (model PWR600-AC-RPS) aan de RPS contactdoos verbinden.

  • Page 125: Attaching The Cisco Rps (Model Pwr675-Ac-Rps-N1

    Varning! Koppla endast Ciscos RPS (modell PWR600-AC-RPS) till RPS-uttaget. Attaching the Cisco RPS (model PWR675-AC-RPS-N1) Attach only the Cisco RPS (model PWR675-AC-RPS-N1) to the RPS receptacle. Warning Statement 100C Waarschuwing Slechts de Cisco RPS (model PWR675-AC-RPS-N1) aan de RPS contactdoos verbinden.
  • Page 126 Attaching the Cisco RPS (model PWR675-AC-RPS-N1) Avertissement Raccordez le bloc d’alimentation Cisco RPS (modèle PWR675-AC-RPS-N1) uniquement au connecteur RPS. Warnung An die RPS-Steckhülse darf nur das Cisco RPS (Modell PWR675-AC-RPS-N1) angeschlossen werden. Avvertenza Collegare soltanto il Cisco RPS (modello PWR675-AC-RPS-N1) alla presa RPS. Advarsel! Koble bare Cisco RPS (modell PWR675-AC-RPS-N1) til RPS-stikkontakten.

  • Page 127: Redundant Power Supply Connection Warning

    Appendix D Translated Safety Warnings Redundant Power Supply Connection Warning Redundant Power Supply Connection Warning Warning If a redundant power system (RPS) is not connected to the switch, install an RPS connector cover on the back of the switch. Statement 265 Waarschuwing Als er geen redundant voedingssysteem (RPS) aan de schakelaar is gekoppeld, dient u een RPS-connectorkapje op de achterkant van de...

  • Page 128: Switch Installation Warning

    Appendix D Translated Safety Warnings Switch Installation Warning Varning! Om ett redundant strömförsörjningssystem (redundant power system, RPS) inte finns anslutet till switchen skall ett RPS-kontaktskydd installeras på switchens baksida. Switch Installation Warning To comply with safety regulations, mount switches on a wall with the front Warning panel facing up.
  • Page 129 Appendix D Translated Safety Warnings Switch Installation Warning Warnung Zur Einhaltung der Sicherheitsvorschriften die Schalter so an einer Wand montieren, dass die Frontplatte nach oben zeigt. Figyelem! A biztonsági elõírások betartása érdekében a kapcsolókat úgy szerelje a falra, hogy az elõlapjuk felfelé nézzen. Avvertenza In conformità...

  • Page 130: Chassis Warning For Rack-Mounting And Servicing

    Appendix D Translated Safety Warnings Chassis Warning for Rack-Mounting and Servicing Chassis Warning for Rack-Mounting and Servicing Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: •...
  • Page 131 Appendix D Translated Safety Warnings Chassis Warning for Rack-Mounting and Servicing Attention Pour éviter toute blessure corporelle pendant les opérations de montage ou de réparation de cette unité en casier, il convient de prendre des précautions spéciales afin de maintenir la stabilité du système. Les directives ci-dessous sont destinées à...
  • Page 132 Appendix D Translated Safety Warnings Chassis Warning for Rack-Mounting and Servicing Advarsel Unngå fysiske skader under montering eller reparasjonsarbeid på denne enheten når den befinner seg i et kabinett. Vær nøye med at systemet er stabilt. Følgende retningslinjer er gitt for å verne om sikkerheten: •...
  • Page 133 Appendix D Translated Safety Warnings Chassis Warning for Rack-Mounting and Servicing Varning! För att undvika kroppsskada när du installerar eller utför underhållsarbete på denna enhet på en ställning måste du vidta särskilda försiktighetsåtgärder för att försäkra dig om att systemet står stadigt. Följande riktlinjer ges för att trygga din säkerhet: •...
  • Page 134 Appendix D Translated Safety Warnings Chassis Warning for Rack-Mounting and Servicing • • • • • • Catalyst 2984G, 2948G-GE-TX, and 2980G Switch Hardware Installation Guide D-24 78-6286-05...

  • Page 135: I N D E X

    I N D E X 802.1D Spanning Tree Numerics 802.3z, IEEE 10/100/1000 ports 802.3z 1000BASE-LX, IEEE standard 4-3, 4-11 connecting to 3-20 to 3-22 described 10/100BASE-T 10/100 ports airflow 1-9 to 1-11 connecting to 3-20 to 3-22 attaching the cable guide 3-15 described autonegotiation...
  • Page 136 3-15 site planning cabling Cisco Discovery Protocol GBIC 4-4, 4-5 See CDP mode-conditioning 4-10 Cisco Group Management Protocol Catalyst 2948G-GE-TX switch See CGMP 10/100/1000 ports heat dissipation command-line interface illustration See CLI management ports 1-8, 3-22 commands Catalyst 2948G switch...
  • Page 137 Index cooling 1000BASE-X See airflow 100BASE-T crossover cable 10BASE-T connecting to 10/100/1000 ports 3-21 10/100 ports 3-21 customer service, contacting fan assembly CWDM GBICs see airflow see 1000BASE-X (CWDM) GBICs features, switch 1-4 to 1-6 CWDM SFP modules frequency, specifications A-3, A-5, A-7 see 1000BASE-X (CWDM) SFP modules GBICs...
  • Page 138 Index grounding wall-mounting 3-16 holes Catalyst 2948G-GE-TX switch 3-16 to 3-18 procedure invisible radiation warning 2-5 to 2-7 D-10 to D-11 tools laser radiation warning D-11 to D-13 heat dissipation laser transmission Catalyst 2948G-GE-TX switches Layer 2 forwarding 2-2, A-3, A-5 Catalyst 2948G switches 2-2, A-3, A-5 LEDs...
  • Page 139 Index Media Access Control addresses installing 4-11 See MAC addresses mode-conditioning 4-4, 4-6 media-dependent interface crossed-over Port Aggregation Protocol connectors 3-22 See PAgP memory A-3, A-7 port cabling specifications microprocessor A-3, A-7 ports locations mounting, table- or shelf- 3-19 management mounting, wall-mounting 3-16 power...
  • Page 140 Index procedures connecting system ground rack-mounting connecting to an SFP module 4-12 to 4-16 Catalyst 2948G and 2980G connecting to the console serial port 3-22 switches 3-7 to 3-9 connecting to the Ethernet management Catalyst 2948G-GE-TX switch 3-10 to 3-15 port 3-22 rack-mounting kit...
  • Page 141 Index SFP modules switch verification 3-23 connecting to system component level problems 4-12 to 4-16 shelf-mounting 3-19 shipping container contents (Catalyst 2948G and 2980G switches) table-mounting 3-19 container contents (Catalyst 2948G-GE-TX technical assistance, obtaining xxiv switches) telco racks instructions terminals show port command connecting to the console serial port 3-22...
  • Page 142 Index VLAN Trunk Protocol See VTP (VLAN Trunk Protocol) VTP (Virtual Terminal Protocol) VTP (VLAN Trunk Protocol) wall-mounting 3-16 warning definition D-2 to D-4 invisible radiation D-10 to D-11 laser radiation D-11 to D-13 qualified personnel information D-9 to D-10 rack mounting D-20 to D-24 RPS 300...

This manual is also suitable for:

Catalyst 2984gCatalyst 2948g-ge-txCatalyst 2980g

Table of Contents