EAW SB730 Owner's Manual page 21

6.7.4 Attaching SB730s to SB730s Already Suspended
NOTE: SB730s should always be flown tight-packed to each other.
1. Move an SB730 Pallet so its SB730 is positioned under the bottom SB730 of the array.
2. Remove the four Quick Release Pins from the Hinges of the SB730 on the pallet.
3. Lower the array until the bottom SB730 barely touches the SB730 on the Pallet.
4. Slide the four Hinges of the SB730 on the pallet into the suspended SB730's Hinge
Tubes. Align Hole 2 of each Hinge with the Hinge Tube Hole.
5. Attach the Hinges to the Hinge Tubes by inserting a Quick Release Pin (removed in Step
2) through both. The result will be tight-packed SB730s.
6. Repeat Steps 1 to 5 for additional SB730s.
6.7.5 Attaching a KF730 to an SB730 Already Suspended
CAUTION: When attaching Hinges to Hinge Tubes in steps 6 and 9, use the correct holes as
determined by the KF730 Wizard or by the user-desired angles to achieve the desired splay
angle. Failure to follow this instruction can result in poor acoustical performance.
1. Move a Pallet with the KF730 to be attached to the rigging location.
2. Lift the KF730 enclosure off the pallet and lay it down, positioned so its hinges are on top
and the enclosure is directly below the array. The KF730 may be laid on the floor or on a
standard road case lid at a comfortable working height.
3. Remove the six Quick Release Pins from the rear Hinges of the KF730.
4. Lower the array until the bottom SB730 barely touches the front of the KF730.
5. Slide the two front Hinges of the KF730 into the suspended SB730's front Hinge Tubes.
6. Attach the Hinges to the Hinge Tubes by inserting a Quick Release Pin (removed in Step
2) through both.
7. Employing two people, one lifts the rear of the KF730, rotating it on the attached front
Hinges.
8. The second person slides the two rear Hinges of the KF730 into the rear Hinge Tubes of
the suspended SB730.
NOTE: It will usually be necessary to nudge the KF730 enclosure being attached backwards
to line up its Hinges with the Hinge Tubes on the SB730.
9. Attach the Hinges to the Hinge Tubes by inserting a Quick Release Pin (removed in step
8) through both.
10. Insert each a Quick Release Pin (removed in step 2) into each of the enclosure's rear
Hinge Tubes as a locking pin. See "Locking Pins" Section 6.4.5.
6.7.6 Attaching KF730s to KF730s Already Suspended
CAUTION: When attaching Hinges to Hinge Tubes in steps 5 and 10, use the correct holes as
determined by the KF730 Wizard or by the user-desired angles to achieve the desired splay
angle. Failure to follow this instruction can result in poor acoustical performance.
1. Move a KF730 Pallet so the top rear Hinges of a KF730 are below the rear Hinge Tubes
of the bottom KF730 in the array.
2. Remove the six Quick Release Pins from the rear of the KF730 on the pallet.
3. Lower the array until the rear Hinge Tubes of the bottom suspended KF730 are even with
the top of the rear Hinge Tubes of the KF730 on the pallet.
4. Extend and slide the Hinges of the KF730 on the pallet into the suspended KF730's
Hinge Tubes.
NOTE: Bump the array slightly as needed to line up the enclosures so the Hinges slide easily
into the Hinge Tubes.
RD0169 (A) KF730 & SB730 OWNER'S MANUAL Page 21 of 28