Alliance Laundry Systems HC18PC2 Operation & Maintenance Manual
Cabinet hardmount s, p, and v-series microcomputers coin and non-coin models
Hide thumbs
Also See for HC18PC2:
- Troubleshooting manual (110 pages) ,
- Installation & maintenance (150 pages) ,
- Installation manual (80 pages)
Table of Contents
Advertisement
Quick Links
Washer-Extractors
Cabinet Hardmount
S, P, and V-Series Microcomputers
Coin and Non-Coin Models
Refer to Page 2 for Model Identification
CHM166C
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. F232137R4
www.comlaundry.com
September 2008
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Alliance Laundry Systems HC18PC2
Summary of Contents for Alliance Laundry Systems HC18PC2
- Page 1 Washer-Extractors Cabinet Hardmount S, P, and V-Series Microcomputers Coin and Non-Coin Models Refer to Page 2 for Model Identification CHM166C Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) Part No. F232137R4 www.comlaundry.com September 2008...
-
Page 3: Table Of Contents
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. F232137 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction... Model Identification ... -
Page 4: Model Identification
HC27VX2 HC60VNF HC30SN2 HC60VX2 HC30VC2 HC80PC3 HC30VX2 HC80SN3 HC35PC2 HC80VCV HC35SN2 HC80VNV HC35VC2 HC80VXV © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction NC18VC2 SC35PC3 NC18VX2 SC35SN2 NC25VC2 SC35VN2 NC25VX2 SC35VNV NC27VC2 SC40VN2 NC27VX2 SC40VNV NC35VC2... -
Page 5: Replacement Parts
Nameplate Figure 1 F232137 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Replacement Parts If literature or replacement parts are required, contact the source from whom the machine was purchased or contact Alliance Laundry Systems at (920) 748-3950 for the name and address of the nearest authorized parts distributor. -
Page 6: Explanation Of Safety Messages
NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information Important Safety Instructions To reduce the risk of fire, electric shock,... - Page 7 If this occurs, have washer checked by a qualified service person. F232137 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 20. If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.
-
Page 8: Safety Decals
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Be careful around the open door, particularly when loading from a level below the door. Impact with door edges can cause personal injury. -
Page 9: Operator Safety
Machine is not connected to a properly grounded circuit. F232137 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Do not bypass any safety devices in the machine. Never operate the machine with a bypassed or disconnected balance system. -
Page 10: Control Panel
Keys for Standard OPL Keys for Icon OPL Keys for VC2, VCV, VX2, VXV Figure 2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operation The Up and Down selection. Press these keys to move among cycles from smaller to greater, or greater to smaller. -
Page 11: Display Indications
Temperature sensor failure or temperature out of range * Display indications separated by a slash (/) represent an alternating display. F232137 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Display bFIL Warm fill (both hot and cold) - Page 12 “tINE” followed by time for spin * Machines shipped to France only. ** Display indications separated by a slash represent an alternating display. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Display Indications for P-Series – Coin Display...
- Page 13 Wash speed forward in test cycle FrEE “Free” cycle option * Display indications separated by a slash (/) represent an alternating display. F232137 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Display Indications for V-Series – Coin Display HFIL SUP0...
- Page 14 AFIL Auxiliary fill (Setup option) Low water level * Display indications separated by a slash (/) represent a flashing display. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Display Medium water level High water level SUP1...
- Page 15 Temperature sensor failure or temperature out of range * Display indications separated by a slash (/) represent a flashing display. F232137 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Display FIL6 Sixth fill (8th of 11 segments)
-
Page 16: Operating Instructions
Figure 3 and Figure 4. DOOR UNLOCK Figure 4 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 3. Load to capacity whenever possible. DO NOT OVERLOAD. Refer to Figure 5. 4. Close door and turn handle counterclockwise until button pops out. - Page 17 Softener Figure 7 F232137 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 7. For coin models: Insert required number of coins to start machines. Refer to Figure 7. 8. For non-coin models: Press the Start key.
-
Page 18: Beginning Of Day
The door should not open. If the door lock and interlock are not functioning properly, call a service technician. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Maintenance End of Day 1. Clean the door gasket of residual detergent and all foreign matter. -
Page 19: Monthly
If water does not leak out during the first wash segment, the drain valve is closed and functioning properly. F232137 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Monthly NOTE: Disconnect power to the machine at its source before performing the monthly maintenance procedures. - Page 20 16.8 in. (426 mm) Motor-Basket 22.1 in. (561 mm) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT NOTE: Hoses and other natural rubber parts deteriorate after extended use. Hoses may develop cracks, blisters or material wear from the temperature and constant high pressure they are subjected to.
- Page 21 Never mix two types of grease, such as petroleum and silicone. F232137 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Figure 12 b. Pump the grease gun slowly, permitting only the following number of strokes: Bearing grease fitting, two strokes ●...
-
Page 22: Quarterly
Open the top cover and remove the control module cover. b. Gently wipe the fan blades clean with a dry cloth. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Quarterly NOTE: Disconnect power to the machine at its source before performing the quarterly maintenance procedures. - Page 23 Filter Element Figure 13 F232137 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 7. For variable speed and F-speed models only, measure the out-of-balance switch gap setting and adjust it as needed. The switch gap settings are listed in the Installation manual, which is supplied with the machine.
-
Page 24: Care Of Stainless Steel
● overheating by scouring with a powder or by employing special chemical solutions. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Do not leave sterilizing solutions on stainless ● steel equipment for prolonged periods of time.
Need help?
Do you have a question about the HC18PC2 and is the answer not in the manual?
Questions and answers