Download Print this page

Kenmore 4810 - 3.5 cu. Ft. I.E.C. High-Efficiency Washer Installation Instructions Manual

Full size tumble action washer
Hide thumbs

Advertisement

Quick Links

®
Full Size Tumble Action
Washers
Before
beginning
installation,
carefully
read
these
instructions.
This will
simpfify
the
installation
and ensure the washer
is installed
correctly
and safely. Leave these instructions
near the washer
after installation
for future
reference.
NOTE: The electrical
service
to the washer
must conform
with
local codes and ordinances
and the latest
edition
of the National
Electrical
Code, ANS!/NFPA
70.
For your safety the information
in
this manual must be followed to minimize the risk
of fire or explosion or to prevent property damage,
personal injury or loss of life.
- Do not store or use gasoline or other flammable
vapors and liquid in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Clear the room, building
or area of all
occupants.
• Immediately
call your gas supplier from a
neighbor's phone. Follow the gas suppliers
instructions.
• If you cannot reach your gas supplier, call
the fire department.
Installation
and service must be performed
by a
qualified
installer,
service agency
or the gas
supplier.
Printed in U.S.A.
Contents
S UBJECT
PAGE
Pre-lnstallation Requirements
2
Electrical Requirements
2
Grounding Requirements
2
Water Supply Requirements
2
Drain Requirements
2
Rough-In Dimensions
3
Location Of Your Washer
4
Unpacking
4-5
Installation
5-6
Replacement Parts
6
Sears, Roebuck and Co.,
Hoffman Estates, IL 60179 U.S.A.
_N 134906800(0706)

Advertisement

loading

  Related Manuals for Kenmore 4810 - 3.5 cu. Ft. I.E.C. High-Efficiency Washer

  Summary of Contents for Kenmore 4810 - 3.5 cu. Ft. I.E.C. High-Efficiency Washer

  • Page 1 ® Full Size Tumble Action Washers Before beginning installation, carefully read these instructions. This will simpfify installation and ensure the washer is installed correctly and safely. Leave these instructions near the washer after installation for future reference. NOTE: The electrical service to the washer must conform...
  • Page 2 absence of local codes, with the National Electrical PRE-INSTALLAT!ON REQUIREMENTS Codes, ANSI/NFPA 70 (latest edition). If in doubt, call a licensed electrician. DO NOTcut off or alter Tools Required for Installation: the grounding prong on the power supply cord. In Phillips screwdriver situations where a two-slot receptacle is present, 10 mm socketwith...
  • Page 3 ROUGH-IN DIMENSIONS Power" Cord . 40 inches(cm) NOTE: For pedestal installations, see additional installation instructions included with the pedestal. For stacking installations, see additional installtion instructions included with the stacking kit. For under counter installations, no special top is required. 8 °...
  • Page 4 LOCATION OF YOUR WASHER DO NOT INSTALL YOUR WASHER: In an area exposed to dripping water or outside weather conditions. The ambient temperature should never be below 60 ° F (15.6 ° C) for proper washer (detergent breakdown) operation. In an area where it will come in contact with curtains or drapes. In an area (garage or garage-type building) where gasoline of other flammables are kept or stored (including automobiles).
  • Page 5 Carefully return the washer to an upright position. Carefully move the washer to within 4 feet (122cm) of the final location. Remove the following from the back panel of the washer: 4 shipping bolts, 4 spacers, I metal "P" clamp, Remove: 2 hose clips.
  • Page 6 iNSTALLATiON (CON'T) 5. Attach drain hose hanger (shipped in washer tub) to drain hose. Place the hook end of the drain hose in the drain opening. Secure the drain hose with the cable tie (provided in the enclosure package) to the standpipe, inlet hose, laundry tub, etc.