BDL3245E / BDL4245E / BDL4645E Safety Instructions Warnings and Precautions KNOW THESE SAFETY SYMBOLS CAUTION: T O REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product. This symbol alerts you that important literature concerning operation and maintenance has been included with this product. Note to CATV system installer: This reminder is provided to call CATV system installer’s attention to Article 820-40 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I), that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.
BDL3245E / BDL4245E / BDL4645E Regulatory Information CE Declaration of Conformity MMD declare under our responsibility that the product is in conformity with the following standards • EN60950-1:2006+A11:2009 (Safety requirement of Information Technology Equipment) • EN55022:2006+A1:2007 (Radio Disturbance requirement of Information Technology Equipment) • EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment) • EN61000-3-2:2006 (Limits for Harmonic Current Emission) • EN61000-3-3:2008 (Limitation of Voltage Fluctuation and Flicker) following provisions of directives applicable • 2006/95/EC (Low Voltage Directive) • 2004/108/EC (EMC Directive) • 2005/32/EC (EuP, Energy-using Product Directive) EC No. 642/2009 Implementing • 93/68/EEC (Amendment of EMC and Low Voltage Directive) and is produced by a manufacturing organization on ISO9000 level. Federal Communications Commission (FCC) Notice (U.S. Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 4
BDL3245E / BDL4245E / BDL4645E Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source. The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A). To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be located near the equipment and easily accessible. A protection mark “B” confirms that the equipment is in compliance with the protection usage requirements of standards PN-93/T-42107 and PN-89/ E-06251. Electric, Magnetic and Electronmagnetic Fields (“EMF”) 1. MMD manufactures and sells many products targeted at consumers, which, like any electronic apparatus, in general have the ability to emit and receive electromagnetic signals.
Page 5
BDL3245E / BDL4245E / BDL4645E Information for U.K. only WARNING - THIS APPLIANCE MUST BE EARTHED. Important: This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5A.
Page 7
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ. End-of-Life Disposal Your new TV/Monitor contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the amount of reusable materials and to minimize the amount to be disposed of. Please find out about the local regulations on how to dispose of your old monitor from your local Philips dealer. (For customers in Canada and U.S.A.) This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations. For additional information on recycling contact www.eia.org (Consumer Education Initiative) Waste Electrical and Electronie Equipment-WEEE Attention users in European Union private households This marking on the product or on its packaging illustrates that, under European Directive 2002/96/EG governing used electrical and electronic appliances, this product may not be disposed of with normal household waste.
BDL3245E / BDL4245E / BDL4645E Table Of Contents Unpacking and Installation ........1 OSD Menu (Need Check) .........15 1.1. Unpacking ..............1 4.1. Navigating the OSD Menu ......15 1.2. Package Contents .............1 4.1.1. Navigating the OSD menu using the remote control........15 1.3. Installation Notes ............1 4.1.2.
BDL3245E / BDL4245E / BDL4645E Unpacking and Installation 1.1. Unpacking • This product is packed in a carton, together with the standard accessories. • Any other optional accessories will be packed separately. • The weight of the product differs - depending on the type. Due to the size and weight, it is recommended to move it by 2 people. • After opening the carton, ensure that the content is in good condition and complete. 1.2. Package Contents Please verify that you received the following items with your package content: • LCD monitor • CD ROM • Remote control with AAA batteries • Power cord (1.8 m) • VGA signal cable (1.8 m) • Quick Installation Guide POWER • Table stand...
BDL3245E / BDL4245E / BDL4645E 1.4. Installing and Removing Table Stands To install table stands: 1. Power off the monitor. 2. Spread a protective sheet on a flat surface. 3. Grab the carrying handles and place the monitor face-down on the protective sheet. 4. After inserting the stand in the guide block, tighten the screws on both sides of the monitor. NOTE: T he long-end side of the stand should face to the front while installing. Carrying handle Thumbscrews Longer portions directs to the front Table stand To remove table stands: 1.
BDL3245E / BDL4245E / BDL4645E 1.5. Mounting on a Wall To mount this monitor to a wall, you will have to obtain a standard wall-mounting kit (commercially available). Using mounting interface that complies with TÜV-GS and/or UL1678 standard in North America is recommended. Protective Sheet Table Tabletop stand 1. Lay a protective sheet on a table, which was wrapped around the monitor when it was packaged, beneath the screen surface so as not to scratch the screen face. 2. This device cannot be used or installed without the Tabletop Stand or other mounting accessory. Make sure all these stuffs are ready for wall-mount installation. 3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting procedures could result in damage to the equipment or injury to the user or installer.
BDL3245E / BDL4245E / BDL4645E 1.6. Mounting in Portrait Position This monitot can be installed in portrait position. 1. Remove the table stand if they are attached. 2. The “ ” logo should be on the LEFT side when facing the monitor. 1.6.1. How to use the logo guider for portrait position a. B efore applying, make sure that the guider is in good condition. Fold the “ ” logo back in at the end of the guider. b. P eel off the back side of the protective film from the logo. c.
BDL3245E / BDL4245E / BDL4645E Parts and Functions 2.1. Control Panel MUTE INPUT MENU POWER button NOTE: “Keyboard Control Lock Mode” This function completely disables the access to all Keyboard Control functions. To Switch the power on or put the monitor to standby. enable or disable the keyboard control lock, press both [ MUTE button and [ ] buttons and hold down continuously for more than Switch the audio mute ON/OFF. 3 (three) seconds. R emote control sensor and power status indicator INPUT button Set the function while OSD menu is on, or to activate input • Receives command signals from the remote control.
BDL3245E / BDL4245E / BDL4645E 2.2. Input/Output Terminals BDL3245E BDL4245E/BDL4645E BDL3245E (OUT) (OUT) (OUT) (IN) (IN) (IN) BDL4245E/BDL4645E (OUT) (OUT) (OUT) (IN) (IN) (IN) MAIN POWER SWITCH AUDIO IN 1, 2, 3 Press to switch the main power on/off. Connect audio input from external AV device. • AUDIO IN 1: 3.5mm stereo phone jack AC IN •...
BDL3245E / BDL4245E / BDL4645E 2.3. Remote Control [DISPLAY] button Press to turn on/off the information OSD displayed on the upper 2.3.1. General functions right corner of the screen. [ ] button • Press to move the selection left in OSD menu. POWER • Press to decrease the value in OSD menu. • Press to move the sub-picture left in PIP mode. VIDEO AUDIO SMART SOURCE SOURCE [SET] button Press to activate the setting with OSD menu. [AUTO ADJUST] button Press to run the Auto Adjust function. NOTE: T his button is functional for VGA input only. ON/OFF INPUT CHANGE...
BDL3245E / BDL4245E / BDL4645E 2.3.2. Inserting the batteries in the remote control The remote control is powered by two 1.5V AAA batteries. To install or replace batteries: 1. Press and then slide the cover to open it. 2. Align the batteries according to the (+) and (–) indications inside the battery compartment. 3. Replace the cover. Caution: An incorrect use of batteries can result in leaks or bursting. Be careful especially about the following points. • Place “AAA” batteries matching the (+) and (–) signs on each battery to the (+) and (–) signs of the battery compartment. • Do not mix battery types. • Do not combine new batteries with used ones. It causes shorter life or leakage of batteries. • Remove the dead batteries immediately to prevent it from liquid leaking in the battery compartment. Don’t touch exposed battery acid, it cause damage to your skin.
BDL3245E / BDL4245E / BDL4645E Connecting External Equipment 3.1. Using the Switch Cover A cover for the main switch is provided to prevent the monitor from being turned on or off accidentally. To lock the cover into position: 1. Align and insert the cover to the ditch located beside the main switch. 2. Use the screw to lock the cover. BDL3245E: Screw Main switch cover BDL4245E / BDL4645E: Screw Main switch cover...
BDL3245E / BDL4245E / BDL4645E 3.3. Connecting a PC 3.3.1. Using VGA input From analog VGA output Mini D-Sub 15 pin From audio output PC or IBM compatible To [AUDIO IN 1, 2, 3] To [VGA IN] 3.3.2. Using DVI input From DVI output From audio output PC or IBM compatible...
BDL3245E / BDL4245E / BDL4645E 3.5. Connecting Monitors in a Daisy-chain Configuration You can interconnect multiple sets of this monitor to create a daisy-chain configuration for applications like a TV wall. NOTE: M aximum 25 displays (5x5) can be used in a daisy-chain configuration. 3.5.1. Video connection Do one the following connections: • Connect the [RS232C OUT] connector of monitor 1 to the [RS232C IN] connector of monitor 2. • Connect the [VGA OUT] connector of monitor 1 to the [VGA IN] connector of monitor 2. • Connect the [VIDEO OUT] connector of monitor 1 to the [VIDEO IN] connector of monitor 2. To RS-232C IN To RS-232C OUT To RS-232C IN RS-232C Cable RS-232C Cable 3.5.2.
BDL3245E / BDL4245E / BDL4645E OSD Menu (Need Check) Brightness Adjust the overall image brightness by changing the intensity of the LCD An overall view of the On-Screen Display (OSD) structure is shown panel’s backlight. below. You can use it as a reference for further adjusting your monitor. Contrast 4.1. Navigating the OSD Menu Adjust to sharpen the picture quality. The black portions of the picture become richer in darkness and the white become brighter. 4.1.1. Navigating the OSD menu using the Sharpness remote control Adjust to improve detail. Black level Adjust to change the image brightness. MENU Noise reduction Adjust to remove the noise in the image.
BDL3245E / BDL4245E / BDL4645E 4.2.2. Screen menu 21:9 The picture is enlarged to 16:9 format. This H position mode is recommended when displaying Picture pictures that have black bands at the top and V position bottom (letterbox format). Screen Clock Clock phase Audio Custom zoom Zoom mode Custom zoom You can use this function to further customize the zoom settings to suit the image you want to display. Screen reset Configuration1 NOTE: T his item is functional only when the Zoom mode setting is Configuration2 set to Custom.
BDL3245E / BDL4245E / BDL4645E Volume Main Picture HDMI YPbPr S-Video Video Adjust to increase or decrease the audio output level. Sub Picture Mute Turn the mute function on/off. HDMI Audio source YPbPr Select the audio input source according to the audio signal source S-Video connected to the audio input and HDMI sockets on the monitor. Video (O: PIP function available, X: PIP function unavailable) The options are: {HDMI} / {Audio1} / {Audio2} / {Audio3}. By pressing the [PIP ON/OFF] button on the remote control, you can Audio reset change the mode in the order shown below: Reset all settings in the AUDIO menu.
BDL3245E / BDL4245E / BDL4645E Language Factory reset Select the language used in the OSD menu. The options are: { } / { } / { } / { } / { } / } / { } / { } / { Panel saving Reset Cancel Choose to enable the panel saving functions to reduce the risk of the “image persistence”. 4.2.6. Configuration2 menu • {Cooling Fan} - Select {On} to turn on the cooling fan all the time. Select {Auto} to turn on/off the cooling fan according to the monitor temperature. OSD turn off Picture Information OSD NOTE: T he speed of the cooling fan is pre-set to {low}, {mid}, or...
BDL3245E / BDL4245E / BDL4645E 4.2.7. Advanced option menu per-second (24 fps) input signal format to DVD video signal format. Once this function is enabled, it is recommended that you set the {Scan conversion} function to {Progressive}. Input resolution Picture • {Off} - Disable the film mode frame conversion function. This mode Black level expansion is suitable for TV broadcasting and VCR signals. Screen Gamma selection Scan mode IR control Audio Scan conversion Select the operation mode of the remote control when multiple Film mode monitors are connected via the RS232C connection.
Page 28
BDL3245E / BDL4245E / BDL4645E Example: 5 x 5 screen matrix (25 monitors) Heat status H monitors = 5 monitors This function allows you to check the thermal status of the monitor at V monitors = 5 monitors any time. The accuracy of the temperature indicated is +/- 5 degrees (C or F). H monitors Date and time Adjust the current date and time for the monitor’s internal clock. Position Date and time Year 2011 Month Hour Minute Daylight saving time • H monitors - Select the number of monitors on the horizontal side.
Page 29
BDL3245E / BDL4245E / BDL4645E Advanced option reset Schedule Reset all settings in the Advanced option menu. 1. Press [SET] or [ ] button to enter the submenu. 2. Press [ ] or [ ] button to select {Reset} and press the [SET] button to restore settings to factory preset values. Today 2011 . 08 . 04 20 : 19 : 55 3. Press the [EXIT] button or select {Cancel} and press the [SET] Input button to cancel and then return to the previous menu. Every day Picture Schecule Action Every week Screen...
Philips strives to deliver the highest quality products. We use some of the industry’s most advanced manufacturing processes and practice stringent quality control. However, pixel or sub-pixel defects on the PDP / TFT panels used in Plasma- & LCD- displays are sometimes unavoidable. No manufacturer can guarantee that all panels will be free from pixel defects, but Philips guarantees that any Plasma- & LCD- displays with an unacceptable number of defects will be repaired during the warranty period in line with your local guarantee conditions. This notice explains the different types of pixel defects and defines the acceptable defect level for this LCD screen. In order to qualify for repair under warranty, the number of pixel defects must exceed a certain level which is given in the reference table. If the LCD screen is within specification a warranty exchange / claim back will be refused. Additionally, because some types or combinations of pixel defects are more noticeable than others, Philips sets even higher quality standards for those. 6.1. Pixels and Sub-Pixels A pixel, or picture element, is composed of three sub-pixels in the primary colors of red, green and subpixel blue.
Dark Dot Defects Black dot defects appear as pixels or sub-pixels that are always dark or “off ”. These are the examples of black dot defects: One dark dot Two adjacent dark dots = 1 pair of dark dots Two dark dots, specifications defines the minimum distance between dark dots 6.5. Proximity of Pixel Defects Because pixel and sub-pixels defects of the same type that are nearby one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects. In the table below you can find specifications about: • Allowed amount of adjacent dark dots = (adjacent dark dots =1 pair of dark dots) • Minimum distance between dark dots • Total no. of all defective dots 6.6. Pixel Defect Tolerances In order to qualify for repair due to pixel defects during the warranty period, a PDP / TFT panel in a Philips Plasma / LCD- display must have pixel or sub- pixel defects exceeding the tolerances listed in the following table.
BDL3245E / BDL4245E / BDL4645E Cleaning and Troubleshooting (Need Check) 7.1. Cleaning Cautions When Using the Display • Do not bring your hands, face or objects close to the ventilation holes of the display. Top of display is usually very hot due to the high temperature of exhaust air being released through the ventilation holes. Burns or personal injuries may occur if any body parts are brought too close. Placing any object near the top of the display could also result in heat related damages to the object as well as the display itself. • Be sure to disconnect all cables before moving the display. Moving the display with its cables attached may damage the cables and thus case fire or electric shock danger. • Disconnect the power plug from the wall outlet as a safety precaution before carrying out any type of cleaning or maintenance procedure. Front Panel Cleaning Instructions • The front of the display has been specially treated.
BDL3245E / BDL4245E / BDL4645E 7.2. Troubleshooting Symptom Possible Cause Remedy No picture is displayed 1. The power cord is disconnected. 1. Plug in the power cord. 2. The main power switch on the back of the 2. Make sure the power switch is switched on. monitor is not switched on. 3. Connect a signal connection to the monitor. 3. The selected input has no connection. 4. The monitor is in standby mode. Interference displayed on the monitor or Caused by surrounding electrical appliances or Move the monitor to another location to see is audible noise is heard...
BDL3245E / BDL4245E / BDL4645E Technical Specifications (Need Check) BDL3245E Display Item Specifications Screen Size (Active Area) 32” LCD Aspect ratio 16:9 Number of pixels 1920 (H) x 1080 (V) Pixel pitch 0.36375 (H) x 0.36375 (V) [mm] Displayable colors 1.06B colors Brightness (typical) 500 cd/m2 Dynamic contrast ratio 3000:1 Contrast ratio (typical) 1450:1 Viewing angle 178 degrees In/Out Terminals Item Specifications Speaker Output Internal Speaker 10W (L) + 10W (R) [RMS]/8Ω 1 Way 1 Speaker System 82 dB/W/M/160 Hz ~ 13 KHz Audio Output RCA Jack x 1 0.5V [rms] (Normal)/ 2 Channel (L+R)
Page 36
BDL3245E / BDL4245E / BDL4645E Environmental Condition Item Specifications Temperature Operational 0 ~ 40°C Storage -20 ~ 60°C Humidity Operational 20 ~ 80% RH (No condensation) Storage 5 ~ 95% RH (No condensation) Pressure Operational 795 ~ 1013 hPa (Altitude: 0 ~ 4,500 m) Storage / Shipment 300 ~ 1013 hPa (Altitude: 0 ~ 9,000 m) Internal Speaker Item Specifications Type 1 Way 1 Speaker Input 10 W (RMS) Impedance 8Ω Output Sound Pressure 82 dB/W/M Frequency Response 160 Hz ~ 13 KHz BDL4245E...
Page 37
BDL3245E / BDL4245E / BDL4645E General Item Specifications Power Supply AC 100 ~ 240V, 50 ~ 60Hz Power Consumption (Max) 260W Power Consumption (typ.) 230W Power Consumption (Standby & Off) <1W (RS232 in active) Dimension (With Stand) [W x H x D] 991.6 x 621 x 329.6 mm Dimension (Without Stand) [W x H x D] 991.6 x 584 x 115.5 mm Weight (With Stand) 24.7 Kg Weight (Without Stand) 23 Kg Gross Weight 28 Kg Environmental Condition Item Specifications Temperature Operational 0 ~ 40°C Storage -20 ~ 60°C Humidity Operational 20 ~ 80% RH (No condensation) Storage 5 ~ 95% RH (No condensation) Pressure...
Page 38
BDL3245E / BDL4245E / BDL4645E RS232C D-Sub Jack x 2 TXD + RXD (1:1) (9 pin) RJ-45 RJ-45 Jack x 1 10/100 Lan Port (8 pin) HDMI Input HDMI Jack x 1 Digital RGB: TMDS (Video + Audio) (Type A) (18 pin) MAX: Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) Audio - 48 KHz/ 2 Channel (L+R) Supports LPCM only DVI-D Input DVI-D jack Digital RGB: TMDS (Video) VGA Input D-Sub Jack x 1 Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω) (15 pin) MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) VGA Output...