Download Print this page

Dynex DX-32L150A11 Quick Setup Manual

32", 37", 40", and 46" lcd tv.
Hide thumbs
   

Advertisement

32", 37", 40", and 46" LCD TV
QUICK SETUP GUIDE
DX-32L150A11, DX-37L150A11, DX-40L130A11,
and DX-46L150A11
Remote control
AC power cord
Component
and
video cable
2 AAA batteries
TV stand and screws
Quick Setup Guide
Front and side features
Remote control
Power
sensor
indicator
Installing the stand
1 Remove the stand from the box and place it on a table or bench.
Note: Pay close attention to the direction of the stand. The wide portion of the stand must
face the front of the TV.
2 Lay the TV on a flat, cushioned surface.
3 Align the stand with the TV, as shown.
Locating
Locators
grooves
Stand
4 Move the stand gently until the locators on the stand column align with the
locating grooves on the stand.
5 Align the holes in the stand with the holes in the stand column.
6 Secure the stand to the column with the screws provided
Installing a wall-mount bracket
1 Carefully place your TV screen face-down on a cushioned, clean surface to
protect the screen from damages and scratches.
2 Remove the four screws holding the TV to its stand column, then remove the
stand column.
3 Secure the wall-mount bracket (not included) to the back of your TV using the
four M6 screws provided with the bracket.
Setting up your remote control
1 While pressing the release button on the battery compartment cover on the
back of the remote, lift the cover off the remote.
2 Insert two AAA batteries into the battery compartment. Make sure that the +
and – symbols on the batteries align with the + and – symbols in the battery
compartment.
3 Replace the cover.
To program your existing remote control to work with your Dynex TV, see the
table below for common codes. If you have problems programming your
remote, or need a different remote control code, visit www.dynexproducts.com
for the latest remote control code information.
Universal remote control TV codes
(for all Dynex TVs manufactured after Jan. 1, 2007)
Universal remote control makers and models
Set-top box makers and models
Philips
RCA
One for All
Sony
Comcast
Dish Network
Motorola
TIVO
PHDVD5, PH5DSS,
RCU807
URC-6690
RM-VL600
M1057
VIP508, VIP622
DRC800
Series 3, HD
PMDVR8, PDVR8
115
135
0464
8043
0463
720
0463
0091
Connecting a DVD or Blu-ray DVD player, cable
box, satellite receiver or game station
Using HDMI (best)
HDMI device
Using component (better)
Back of TV
Component video device
Component
video cable
Using composite(good)
Video device
DirectTV
RC23
10463
Using S-video (fair)
Back of TV
Video device
HDMI cable
(not included)
Connecting an antenna
Connect a 75 ohm cable (not included) to ANT/CABLE IN jack on the back of
your TV and the RF OUT jack on the antenna.
Connecting a home theater system
Using analog audio cable:
Back of TV
Back of TV
Audio cable
Note: Cable connectors and jacks are often color-coded. Match the colors when
you connect the AV cable.
Using digital audio cable:
Composite
video cable
Note: The DIGITAL OUTPUT jack only works with digital TV channels.
Back of TV
Audio cable
S-video cable
Back of TV
Antenna cable
Back of TV

Advertisement

   Related Manuals for Dynex DX-32L150A11

   Summary of Contents for Dynex DX-32L150A11

  • Page 1: Quick Setup Guide

    3 Replace the cover. To program your existing remote control to work with your Dynex TV, see the table below for common codes. If you have problems programming your remote, or need a different remote control code, visit www.dynexproducts.com for the latest remote control code information.

  • Page 2

    Cuajimalpa, Distrito Federal, México 05349 RFC#BBI0802114Q2 © 2009 BBY Solutions, Inc., All Rights Reserved. DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and brand names are trademarks of their respective owners. Move Select...

This manual also for:

Dx-37l150a11, Dx-40l130a11, Dx-46l150a11

Comments to this Manuals

Symbols: 0
Latest comments: