Specifications - Pioneer ND-BC2 - Rear View Camera Owner's Manual

Pull out from here
Hinge
Harness cover
Rear view
camera
Hatch
Fig. 16
Abb. 16
Rear view camera
Hatch
Cord
Fig. 17
Abb. 17
Waterproof pad
Clamps
Make a U-shaped loop in
the lead outside the rubber
packing to prevent rain-
water from flowing along
Rubber packing
the lead into the interior
of the vehicle.
Fig. 18
Abb. 18
Connection <ENGLISH>
Accessory power supply
Note:
• This unit is for vehicles with a 12-volt battery and nega-
To electric terminal controlled by ignition
tive grounding. Before installing it in a recreational vehi-
cle, truck, or bus, check the battery voltage. switch (12 V DC) ON/OFF.
• To avoid shorts in the electrical system, be sure to discon-
Red
nect the battery cable before beginning installation.
Fuse (1A)
• Refer to the owner's manual for details on connecting the
other units, then make connections correctly. Ground
• Secure the wiring with cable clamps or adhesive tape. To
protect the wiring, wrap adhesive tape around them where To vehicle (metal) body.
they lie against metal parts.
Black
• Route and secure all wiring so it cannot touch any mov-
ing parts, such as the gear shift, handbrake and seat rails. Cord installation (Fig. 15)
Do not route wiring in places that get hot, such as near
the heater outlet. If the insulation of the wiring melts or
Clamps
gets torn, there is a danger of the wiring short-circuiting
to the vehicle body. Rear view camera
• Do not shorten any leads. RCA power supply cable
• Never feed power to other equipment by cutting the insu-
Product with a video input jack
lation of the power supply lead of the unit and tapping
(Hideaway unit etc.)
into the lead. The current capacity of the lead will be
Power supply unit
exceeded, causing over heating.
• When replacing the fuse, be sure to only use a fuse of the Made with a rasp etc.
rating prescribed on the fuse holder.
Scuff plate
• To minimize noise locate the TV antenna cable, radio
Clamp
antenna cable and RCA power supply cable as far away
Waterproof plate
from each other as possible.
• Connection to a TV with an RCA video input is possible,
Cord installation points (Fig. 16)
but confirm whether the TV you use has a reverse gear
connection function.
• If this unit is installed in a vehicle that does not have an • When pulling the cord out of the car,
ACC (accessory) position on the ignition switch, the red
pull from the outer side of the hatch har-
lead of the unit should be connected to a terminal coupled
ness cover and hinge.
with ignition switch ON/OFF operations. If this is not
done, the vehicle battery may be drained when you are Pull out from here
away from the vehicle for several hours.
Hinge
Harness cover
Rear view camera
Hatch
After cord installation (Fig. 17, Fig. 18)
• Open and close the hatch door slowly
ACC position No ACC position to confirm that the cord is not rubbing
against the rim of the door.
Rear view camera
• Cords for this product and those for other products may
Hatch
be different colors even if they have the same function.
Cord
When connecting this product to another product, refer to
• When the rear view camera cord cannot
the supplied manuals of both products and connect cords
that have the same function. be pulled out from the lower side due to
the type of car.
Connection sample (Fig. 14)
As shown in the figure 18, bend the cord
into a U shape in front of the waterproof
Power supply unit
pad, making sure that rain water cannot
Rear view camera connector
enter the car by running down the cord.
RCA power supply cable connector
Clamps
Rear view camera
Waterproof pad
Video input jack Rubber packing
Make a U-shaped loop in the lead outside
Connect to video input jack.
the rubber packing to prevent rainwater from
RCA pin
flowing along the lead into the interior of the
vehicle.

Specifications

<ENGLISH>
Power source ........................................... 14.4 V DC Dimensions
Camera unit ... 27 (W) × 27 (H) × 26 (D) mm
(10.8 V to 15.1 V allowable)
1 (W) × 1 (H) × 1 (D) in.
Grounding system .............................. Negative type
Max. current consumption .......................... 120 mA Power supply unit
.................... 70 (W) × 23 (H) × 35 (D) mm
Output video ....................................... Mirror image
2-3/4 (W) × 7/8 (H) × 1-3/8 (D) in.
(for rear view confirmation)
Sensor ............................ 1/4-inch color CCD sensor Weight
No. of pixels ........ 492 (vertical) × 512 (horizontal)
Camera unit ................................ 150 g (0.3 lbs)
(Total no. of pixels: 270 000, (including the cable)
effective no. of pixels roughly 250 000) Power supply unit ...................... 160 g (0.4 lbs)
Lens ........................................................ Wide-angle, (including the power cord)
focal length f = 1.53 mm, F value 2.8
Note:
Angle of view ................... Horizontal: approx. 135º
Specifications and the design are subject to possible
Vertical: approx. 100º
modification without prior notice due to improve-
IR cutoff filter (special filter for vehicle mounting)
ments.
.................................................................. Provided
Iris system .......................................... Electronic iris
Scanning system ........................................ Interlace
Synchronizing system ....... Internal synchronization
Signal-to-noise ratio .......................... 40 dB or more
(at the recommended intensity of illumination)
Horizontal resolution ............ Approx. 300 TV lines
Illumination range .... Approx. 1.5 lux to 100 000 lux
Image output ...................................... 1 Vp-p (75 Ω)
Operation temperature range ........... –30ºC to +70ºC
+22ºF to +158ºF
Storage temperature range .............. –40ºC to +85ºC
–40ºF to +185ºF