Using Bluetooth Wireless Technology - Pioneer DEH-P9400BH Owner's Manual

Section
Operating this unit
02
When you do not want low sounds from the sub-
woofer output frequency range to play from the
front or rear speakers, turn on the HPF (high pass
filter). Only frequencies higher than those in the
selected range are output from the front or rear
speakers.
1 Press M.C. to display the setting mode.
2 Press M.C. to turn high pass filter on or off.
3 Turn M.C. to select the cut-off frequency.
50Hz—63Hz—80Hz—100Hz—125Hz
SLA (source level adjustment)
SLA (Source level adjustment) lets you adjust the
volume level of each source to prevent radical
changes in volume when switching between sour-
ces.
! When selecting FM as the source, you cannot
switch to SLA.
! Settings are based on the FM volume level,
which remains unchanged.
! The AM volume level can also be adjusted with
this function.
1 Press M.C. to display the setting mode.
2 Turn M.C. to adjust the source volume.
Adjustment range: +4 to –4
Using Bluetooth wireless
technology
Using Bluetooth telephone
Important
! Since this unit is on standby to connect with
your cellular phone via Bluetooth wireless
technology, using it without the engine run-
ning can drain the battery power.
! Operations may vary depending on the kind
of cellular phone.
12
En
! Advanced operations that require attention
such as dialing numbers on the monitor,
using the phone book, etc., are prohibited
while driving. Park your vehicle in a safe
place when using these advanced opera-
tions.
Setting up for hands-free phoning
Before you can use the hands-free phoning
function you must set up the unit for use with
your cellular phone.
1 Connection
Operate the Bluetooth telephone connection
menu. Refer to Connection menu operation on
this page.
2 Function settings
Operate the Bluetooth telephone function
menu. Refer to Phone menu operation on page
14.
Basic operations
Making a phone call
! Refer to Phone menu operation on page 14.
Answering an incoming call
1 When a call is received, press M.C.
Ending a call
1 Press
.
Rejecting an incoming call
1 When a call is received, press
.
Answering a call waiting
1 When a call is received, press M.C.
Switching between callers on hold
1 Press M.C.
Canceling call waiting
1 Press
.
Operating this unit
Adjusting the other party's listening volume
1 Turn LEVER while talking on the phone.
! When private mode is on, this function is not
available.
Turning private mode on or off
1 Press BAND/
while talking on the phone.
Switching the information display
1 Press
/DISP while talking on the phone.
Notes
! If private mode is selected on the cellular
phone, hands-free phoning may not be avail-
able.
! The estimated call time appears in the dis-
play (this may differ slightly from the actual
call time).
Connection menu operation
Important
! Be sure to park your vehicle in a safe place
and apply the parking brake when perform-
ing this operation.
! Connected devices may not operate properly
if more than one Bluetooth device is con-
nected at a time (e.g. a phone and a separate
audio player are connected simultaneously).
1 Press and hold to display the connec-
tion menu.
# You cannot operate this step during a call.
2 Turn M.C. to select the function.
After selecting, perform the following proce-
dures to set the function.
Device list (connecting or disconnecting a device
from the device list)
! When no device is selected in the device list,
this function is not available.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the name of a device you
want to connect/disconnect.
! Press and hold M.C. to switch the
Bluetooth device address and device
name.
3 Press M.C. to connect/disconnect the selected
device.
Once the connection is established, Con-
nected is displayed.
Delete device (deleting a device from the device
list)
! When no device is selected in the device list,
this function is not available.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the name of a device you
want to delete.
! Press and hold M.C. to switch the
Bluetooth device address and device
name.
3 Press M.C. to display Delete YES.
4 Press M.C. to delete a device information from
the device list.
! While this function is in use, do not turn off
the engine.
Add device (connecting a new device)