Connections; Projector Position; Projection Distances; Connecting To Computer - Panasonic PT-LB10NTU - Mobile Proj XGA 2000 Lumens 4.9LBS Cross Platform Wrls Operating Instructions Manual

Projector position

Top edge of screen
Screen
L
Bottom edge of screen
L
Screen

Projection distances

Projection distance (L)
4:3 Screen PT-LB10NTU/PT-LB10U/
size PT-LB10SU
(diagonal)
Wide Telephoto
(LW) (LT)
0.84 m(33˝) 1.1 m(3´7˝)
1.02 m(40˝) 1.2 m(3´11˝) 1.4 m(4´7˝)
1.27 m(50˝) 1.5 m(4´11˝) 1.7 m(5´6˝)
1.52 m(60˝) 1.8 m(5´10˝) 2.1 m(6´10˝)
1.78 m(70˝) 2.1 m(6´10˝) 2.4 m(7´10˝)
2.03 m(80˝) 2.4 m(7´10˝) 2.8 m(9´2˝)
2.29 m(90˝) 2.7 m(8´10˝) 3.2 m(10´5˝)
2.54 m(100˝) 3.0 m(9´10˝) 3.5 m(11´5˝)
3.05 m(120˝) 3.6 m(11´9˝) 4.2 m(13´9˝)
3.81 m(150˝) 4.5 m(14´9˝) 5.3 m(17´4˝)
5.08 m(200˝) 6.0 m(19´8˝) 7.1 m(23´3˝)
6.35 m(250˝) 7.5 m(24´7˝) 8.9 m(29´2˝)
7.62 m(300˝) 9.0 m(29´6˝) 10.7 m(35´1˝)
NOTE:
B The dimensions in the table above are approximate.
B If you use the projection distance for the 16:9 screen,
the 4:3 projection image overflows the screen at the top
and bottom.
B For details about projected image distances, refer to
page 61.
20-E
NGLISH
<Units: mm (inch)>
L: Projection distance
SH: Image height
SW:Image width
H1: Distance from center
of lens to bottom edge
of projected image
PT-LB10VU/ Height
PT-LB10SVU position
(H1)
Wide Telephoto
(LW) (LT)
1.1 m(3´7˝) 0.08 m(3-1/8˝)
1.2 m(3´11˝) 1.4 m(4´7˝) 0.09 m(3-17/32˝)
1.5 m(4´11˝) 1.8 m(5´10˝) 0.11 m(4-5/16˝)
1.8 m(5´10˝) 2.1 m(6´10˝) 0.14 m(5-1/2˝)
2.1 m(6´10˝) 2.5 m(8´2˝) 0.16 m(6-9/32˝)
2.4 m(7´10˝) 2.9 m(9´6˝) 0.18 m(7-1/16˝)
2.8 m(9´2˝) 3.2 m(10´5˝) 0.20 m(7-27/32˝)
3.0 m(9´10˝) 3.6 m(11´9˝) 0.22 m(8-21/32˝)
3.7 m(12´1˝) 4.3 m(14´1˝) 0.26 m(10-7/32˝)
4.6 m(15´1˝) 5.4 m(17´8˝) 0.33 m(12-31/32˝)
6.1 m(20´) 7.3 m(23´11˝) 0.44 m(17-5/16˝)
7.6 m(24´11˝) 9.1 m(29´10˝) 0.55 m(21-5/8˝)
9.2 m(30´2˝) 11.0 m(36´1˝) 0.66 m(25-31/32˝)

Connections

Notes on connections
B Read the instruction manual for each peripheral device carefully before
connecting it.
B Turn off the power supply for all peripheral devices before making any
connections.
B If the cables necessary for connection are not included with the peripheral
device or available as an option, you may need to prepare a proper cable
for the device concerned.
B If there is a lot of jitter in the video signal, the projected image may flicker.
In such cases, it will be necessary to connect a TBC (time base corrector).
B Refer to the list on page 60 for details on compatible signals which can be
input to the projector.
B Only one audio system circuit is available for the AUDIO IN L-R
connectors, so if you change the audio input source, you will need to
remove and insert the appropriate plugs.

Connecting to computer

Computer for
control use
Serial adapter
(ET-ADSER : sold
separately)
DIN 8-pin
(male)
RGB signal cable
(accessory)
Computer
Monitor
RGB signal cable
Refer to the accessory CD-
ROM for details on the wireless
network that is used for
controlling the projector with a
personal computer by means
of the wireless card.
(PT-LB10NTU only)
E -21
NGLISH