Material Safety Data Sheet (Msds); Handling And Storage - Oki CX3535MFP Safety Information Manual

Material Safety Data Sheet
# 58409301
Cyan Toner, Type D2: P/N 44947307
For more information, contact Oki Data at: 2000
Bishops Gate Boulevard, Mount Laurel, NJ 08054-
4620.
Emergency Information: call 1-800-654-3282; US and
Canada only.
COMPOSITION/INFORMATION ON
INGREDIENTS
INGREDIENT(S)
Polyester resin
Organic Pigment
Wax
Amorphous Silica
Titanium dioxide 13463-67-7
HAZARDS IDENTIFICATION
Emergency Overview : If used as intended, the product does
not present acute or chronic health hazard.
Physical Hazards : This product is not classified as flammable
or combustible. It will burn in case of fire.
Avoid contact with strong oxidizers such as chromate, bromate
and nitrates.
Routes of Exposure : Inhalation, dermal contact, incidental
ingestion
Inhalation : Excessive inhalation may cause irritation of the
nose, throat and respiratory tract.
Eye Contact : Non-irritant.
Dermal Contact : Non-irritant, non-sensitiser.
Ingestion : Not currently known.
Chronic Effects : See Section 11 Supplemental Health
Information.
Carcinogenicity : See Section 11 Supplemental Health
Information.
Reproductive/Developmental : Not identified.
Target Organs : Prolonged breathing of high concentrations
may cause adverse effects on the respiratory system.
Signs and Symptoms of Exposure : Prolonged exposure to
dusts of this product may irritate the respiratory system.
Medical Conditions Aggravated by Exposure to This
Product : Respiratory disorders, such as asthma, may be
aggravated by prolonged exposure to high concentrations of this
product.
FIRST AID MEASURES
Eye Contact : Immediately flush eyes with plenty of water for at
least 15 minutes. If irritation persists, call a physician.
Skin Contact : Wash with soap and water. Wash clothing before
reuse. If irritation occurs or is persistent, seek medical attention.
Ingestion : Dilute stomach contents with several glasses of
water.
Inhalation : Remove from exposure area to fresh air
immediately. Contact a physician if there is any difficulty in
breathing or other signs of distress.
CAS No. wt.%
— 80-90
— <10
— <10
7631-86-9 <5
<2
— TRADE SECRET
FIRE FIGHTING MEASURES
General Hazard : Product will burn in case of fire.
Flash Point : Not applicable
Flammable Limits : Not applicable
Autoignition Temperature : Not applicable
Flammability classification : Not applicable
Extinguishing Media : Foam, halon, carbon dioxide, dry
chemical & water fog.
Unusual Fire & Explosion Hazard : Combustible powder. Dust
of this product at sufficient concentrations can form explosive
mixtures with air.
Fire Fighting Procedures : None
Hazardous Combustion Products : Carbon monoxide, carbon
dioxide and smoke.
ACCIDENTAL RELEASE MEASURES
Spills or Leaks : Vacuum-clean spilled toner and carefully
transfer into sealable waste container. If no vacuum-cleaner is
available, sweep slowly to minimize generation of dust during
clean-up. Residue can be removed with soap and cold water.

HANDLING AND STORAGE

Handling : Avoid dust, keep away from ignition sources.
Prevention of Fire and Explosion : This material is capable of
creating a dust explosion. Keep away from heat, sparks & flame.
Storage : Keep container in cool and dry area.
Hygienic Practices : Avoid inhalation and ingestion. Avoid
getting in eyes, on skin or clothing. Wash hands thoroughly after
handling, and before eating, drinking, or smoking.
EXPOSURE CONTROLS/PERSONAL
PROTECTION
Exposure Limits
OSHA PELs (TWA) as the product : 15mg/m3 (Total dust)
5mg/m3 (Respirable fraction)
Other substances : Not listed
ACGIH TLVs (TWA) as the product : 10mg/m3 (Total dust)
3mg/m3 (Respirable fraction)
Other substances : Not listed
DFG-MAK (TWA) as the product : 4mg/m3 (Inhalable fraction)
1.5mg/m3 (Respirable fraction)
All substances : Not listed
NOHSC (TWA) All substances : Not listed
Engineering Controls : Maintain adequate ventilation.
Eye Protection : Not required under intended use.
Skin Protection : Not required under intended use.
Respiratory Protection : Not required under intended use.
PHYSICAL AND CHEMICAL PROPERTIES
Appearance : Fine solid powder
Color : Cyan
Scent : Odorless
Melting Point : 110 - 150 degree (Softening point)
Specific Gravity(H2O=1) : 1.1 - 1.5
Vapor Pressure : Not applicable
Vapor Density (Air=1) : Not applicable
Evaporation Rate : Not applicable
Solubility in Water : Negligible
pH Value : Not a water-based product, therefore not applicable.
8 - English